ACW Enclosure with External Display Installation Instructions Document #101-0036 1 03/20/06 TABLE OF CONTENTS
I. INTRODUCTION ................................................................................................... 3 II. INSTALLATION................................................................................................... 4
INSTALLATION OF ENCLOSURE ........................................................................................ 4 DIAGRAM A............................................................................................................ 6 DIAGRAM B............................................................................................................ 7 DIAGRAM C ........................................................................................................... 8 DIAGRAM D ........................................................................................................... 9
INSTALLATION OF WIRING FOR DISPLAY ..................................................................... 10 III. OPERATION ...................................................................................................... 12 IV. PROGRAMMING .............................................................................................. 13 V. TROUBLESHOOTING ...................................................................................... 14 Document #101-0036 2 03/20/06 I. INTRODUCTION
The Hamilton Manufacturing External Display is a bright, highly visible message center designed not only to help customers through their transaction, but also to attract new customers. The External Display provides a 3" x 18" scrolling display visible from hundreds of feet away that is sure to attract attention. While waiting for a customer to start a transaction, the External Display can display the same messages as the ACW Controller, or custom messages that have been programmed by the operator. These custom messages can be anything from additional information on using the car wash to special promotional messages. Such messages could include advertisements for weekly specials or discounted beverage prices in the attached convenience store. As soon as the customer takes some action, such as inserting money or choosing a wash selection, the External Display will automatically duplicate the messages shown on the ACW Controller Display. This helps the customer understand and use the wash more efficiently by seeing the instructions in such a bold fashion. To insure visibility and durability in a variety of situations, the External Display PCB Assembly is protected by a stainless steel enclosure incorporating a 1/4" thick lexan shield. This shield not only helps protect against vandalism, but also helps filter out bright sunlight, making the display extremely visible in nearly all situations. Document #101-0036 3 03/20/06 II. INSTALLATION
INSTALLATION OF ENCLOSURE
STEP 1. STEP 2. STEP 3. Switch off the power to the Auto Cashier at the main breaker panel. Unlock and open the door to the Auto Cashier. Break loose, but DO NOT REMOVE THE ANCHOR BOLT securing the Autocashier to the base. The Auto Cashier becomes top heavy when the door is open. IF BOLTS ARE REMOVED ALL AT ONCE, THE UNIT MAY FALL OVER CAUSING INJURY. STEP 4. STEP 5. STEP 6. Loosen the conduit connectors. Remove the two anchor bolts on the RIGHT SIDE of the bottom of the Auto Cashier. LEAVE THE ANCHOR BOLTS ON THE LEFT SIDE IN PLACE. Lift up the right side of the Autocashier approximately 1/2". Slide the bottom flange of the RIGHT SIDE PIECE under the Auto Cashier. Make sure the front flange of the RIGHT SIDE is in front of the flange that is already part of the Auto Cashier. Maneuver the SIDE PIECE and the Auto Cashier cabinet around until all the holes line up. Reinstall the anchor bolts, but do not tighten completely. Repeat steps 6 & 7 for the LEFT SIDE PIECE. REMOVE ONLY THE LEFT SIDE ANCHOR BOLTS. Set the LIGHT BRACKET on the top of the two SIDE PIECES. Make sure that the SIDE PIECES set outside of the small tabs located at the front, lower outside edges of the LIGHT BRACKET. Install four 10-24 x 3/8" screws to secure the LIGHT BRACKET to the SIDE PIECES. Make sure the edges of the LIGHT BRACKET are flush with the outside surfaces of the SIDE PIECES before tightening the screws. Run conduit up from the conduit hole in the back of the machine to the utility box intended for the fluorescent lamp wiring. Follow all applicable local codes. It is recommended to use a separate breaker for the fluorescent lamp so that it can be turned off during the day. Remove the knockouts from the mounting holes in back of the Auto Cashier cabinet. Remove the 1/4 x 20" nuts from the studs on the BACK PIECE. Push the BACK PIECE studs through the holes on the SIDE PIECES and the back of the cabinet. STEP 7. STEP 8. STEP 9. STEP 10. STEP 11. STEP 12. STEP 13. STEP 14. Document #101-0036 4 03/20/06 STEP 15. STEP 16. STEP 17. STEP 18. Reinstall the 1/4 x 20" nuts onto the studs, but do not tighten. Make sure the SIDE PIECES are pushed toward the center of the cabinet as far as possible and tighten the anchor bolts. Tighten the nuts. The TOP PIECE is designed to slide forward and slip into catches on the rear of the LIGHT BRACKET. Set the TOP PIECE onto the LIGHT BRACKET about two inches rearward of the closed position. Hold the front of the TOP PIECE up about 1/2" to clear the Display and push forward until it stops. Push down on the TOP PIECE to set it in place. Install two security screws from the underside of the LIGHT BRACKET and into the TOP PIECE. STEP 19. Document #101-0036 5 03/20/06 ACW ENCLOSURE DIAGRAM A 2 13 4 17 16 19 24 12 15 18 23 5 8 11 10 22 6 14 21 20 1 19.0 1 2 3 4 5 6 7 8 9 10 CONNECTOR FROM ACTIVE DISPLAY (GREEN) 05-0014 RED BLACK ORANGE WHITE 1 2 3 4 5 6 7 8 9 10 TERMINAL STRIP CONNECTOR 47-0204 9
RED BLACK JUMPER
FROM HARNESS, 48-3047 7 3 WHITE WIRE DIAGRAM FROM ACTIVE DISPLAY TO TERMINAL STRIP, TO HARNESS - ALL WIRES ARE 20 AWG UL1007 - NOT TO SCALE - WIRE LENGTHS ARE CUT TO A TOLERANCE OF ±1/8" PER FOOT SHOWN MOUNTED ON ACW 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 ITEM# 101-0036 96-2054 90-0668 47-0000 47-3012 47-0234 47-3014 90-0667 47-0274 47-0228 90-0129 47-0204 05-0014 63-0325 48-3047 47-0075 61-2105 90-0320 90-0331 90-0148 90-0429 63-0326 61-2104 61-2103 61-2102 61-2101 05-0013 PART# INSTALLATION INSTRUCTION SHEET DECAL, STANDARD INFO LABEL BIT, SPANNER WIRE, 20 AWG UL1007 / FOOT GASKET, SPONGE RUBBER - 5" STRIPS GASKET, U-CHANNEL / FOOT GASKET, EXTERNAL DISPLAY SEAL / FOOT SCREW, #10-24 X 3/4 LG. SPANNER S.S. ZIP STRAP, 6" BLACK NYLON SLEEVE, WHITE NYLON / FOOT SCREW, #6-32 X 3/8 LG. PAN HEAD, CLEAR ZINC PLATE TERMINAL STRIP 10 CONNECTIONS ACTIVE DISPLAY ASSEMBLY LEXAN, 1/4" THICK GUARD HARNESS, ACTIVE DISPLAY TO ACW TERMINAL, C-CONNECT RAIL, LEXAN CLAMP - EXTERNAL DISPLAY NUT, #8-32 NYLON INSERT, CLEAR ZINC PLATE NUT, 1/4 - 20, PLAIN HEX, CLEAR ZINC PLATE SCREW, #10-24 X 3/8 LG. PAN HEAD PHILLIPS WASHER, 1/4 I.D. - PLAIN CLEAR ZINC PLATE LEXAN, RED - EXTERNAL DISPLAY WELDMENT, COVER DISPLAY - HOOD WELDMENT, BACK PANEL - HOOD WELDMENT, RIGHT SIDE - HOOD WELDMENT, LEFT SIDE - HOOD ASSEMBLY, PREP - EXTERNAL DISPLAY DESCRIPTION 1 1 1 6.5 2 2 2 2 2 1.5 2 1 1 1 1 4 1 4 4 8 4 1 1 1 1 1 1 QTY. 61-0590C
Document #101-0036 6 HOOD WITH EXTERNAL DISPLAY
03/20/06 TRANSFORMER DIAGRAM B YELLOW WHITE BLACK 3 2 1 3 2 1 24 VAC L2 L1 BLUE BLACK BLACK 24 VAC L2 L1 24V Document #101-0036
22 POSITION CARD EDGE ADD IN PIN 16
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 SYSTEM SYSTEM CONNECTIONS (FOR ACW 4/5) 7
EXTERNAL DISPLAY TRANSFORMER ASSEMBLY ( 60-0331A )
BLACK RED WHITE/RED L1 HOPPER DROP L2 GND COM WHITE GREEN BROWN L1 HOPPER DROP BLACK RED WHITE/RED TO SYSTEM HARNESS HOPPER PLUG
BROWN WHITE/GREEN COM EMPTY 1 2 3 4 5 6 7 8 9 10 11 L2 GND COM WHITE GREEN BROWN TO HOPPER EXTENSION PLUG 12 COM EMPTY BROWN WHITE/GREEN 4 3 2 1 4 3 2 1 4 3 2 1 ACW CONTROLLER ( 49-1212A ) OR AUTOTEC CONTROLLER ( 49-1201A ) 03/20/06 24V TRANSFORMER Document #101-0036
EXTERNAL DISPLAY COMMUNICATIONS HARNESS ( 48-2130A ) CRC BOX ( 49-0560E ) PLUG IN
1 2 3 4 5 6 7 8 9 10 1 1 2 3 4 HOOD WITH EXTERNAL DISPLAY ASSEMBLY ( 61-0590C) XMIT COM COM 24 VAC WHITE BLACK BLACK RED
1 2 3 4 5 6 7 8 9 DB9 CONNECTOR COM BLACK WHITE XMIT 2 3 4 DIAGRAM C SYSTEM SY STEM CONNECTIONS (For CW-CR -CRC (For ACW -CRC 4/5) 8
XMIT COM 24 VAC WHITE BROWN YELLOW EXTERNAL DISPLAY TRANSFORMER HARNESS ( 48-2139A )
BROWN YELLOW WHITE BLACK COM 24 VAC L2 L1 4 3 2 1 4 3 2 1 COM 24 VAC L2 L1 BLUE BLUE BLACK BLACK EXTERNAL DISPLAY TRANSFORMER ASSEMBLY ( 60-0331A ) L1 HOPPER DROP BLACK RED WHITE/RED WHITE GREEN BROWN L2 GND COM L1 HOPPER DROP BLACK RED WHITE/RED 03/20/06
BROWN WHITE/GREEN TO SYSTEM HARNESS HOPPER PLUG 1 2 3 4 5 6 7 8 9 10 11 COM EMPTY L2 GND COM WHITE GREEN BROWN TO HOPPER EXTENSION PLUG 12 COM EMPTY BROWN WHITE/GREEN 4 3 2 1 4 3 2 1 4 3 2 1 Document #101-0036
1 2 3 4 5 6 7 8 9 10 HOOD WITH EXTERNAL DISPLAY ASSEMBLY ( 61-0590C) XMIT COM COM 24 VAC WHITE BLACK BLACK RED EXTERNAL DISPLAY COMMUNICATION HARNESS ( 48-3047 ) DIAGRAM D SYSTEM SY STEM CONNECTIONS (For (For GOLDLINE ACW) 9
6 7 12 10 9 11 8 13 22 14 3 4 5 1 2
+12V +5V $1 $5 COIN 1 COIN 2 COIN DROP HOPPER EMPTY BUTTON 1 BUTTON 2 BUTTON 3 BUTTON 4 REFUND CONTROLLER EIC CARD READER SOUND PRINTER 15 16 17 18 19 20 21 DISTRIBUTION BOARD ( 05-0019 ) 03/20/06 INSTALLATION OF WIRING FOR DISPLAY
The External Display is powered by a transformer and controlled by the ACW4v4.3B.13ZE Auto Cashier Controller (Part No. 49-1212A), or a later model. The following accessories are used:
P a rt # 49-1212A 60-0331A 48-2129A 48-2130A P a r t D e s c r ip t io n ACW4v4.3B.13ZE Controller External Display Transformer Assembly External Display Transformer Harness External Display Communication Harness Step 1. Mount the Transformer Assembly by first removing the Coin Hopper from the Auto Cashier. Unplug both ends of the cable that connects to the Coin Hopper. Next, remove the two nuts and lockwashers at the back of the Hopper Mounting Plate. Set the Transformer Assembly onto the Hopper Mounting Plate studs with the Transformer facing downwards. Re-install the nuts and lockwashers. Step 2. Remove the 12-pin Hopper Connector that is snapped into a bracket on the rear wall of the Auto Cashier. Plug the 12-pin female connector of the Display Transformer Harness onto the end of the connector just removed from the bracket. Snap the 12-pin male connector of the Display Transformer Harness into the bracket. Re-install the cable that originally connected to the Coin Hopper. Step 3. Connect the square 4-pin male connector of the Display Transformer Harness to the Transformer. Step 4. The singular white wire of the Display Transformer Harness must be connected to the 22-pin edge connector at the top of the Controller. Route the white wire with the existing harness along the rear bottom of the Auto Cashier and follow the harness as it proceeds onto the door and into the Controller Housing. With the Snap Cover off the Controller Housing, gently remove the long, black connector from the top of the Controller. Carefully insert the terminal of the white wire into the small slot marked as #16. Be sure the terminal is inserted far enough so there is no exposed metal (there will be a faint click heard when the terminal reaches its required depth). Step 5. Secure the long 4-pin connector to the rear wall of the Auto Cashier with the supplied stick-on cable clamp in a convenient position. Document #101-0036 10 03/20/06 Step 6. The Data Communication Harness supplied with the kit is connected from the long 4-pin connector to the terminal strip located inside the Hood, splicing in extra wire if necessary. The connections inside the External Display Enclosure should be made as shown below. W i r e C o lo r
RED BLK BLK WHT T e r m in a l #
6 7 8 9 Document #101-0036 11 03/20/06 III. OPERATION
The External Display receives serial data from the ACW Controller. The data received is then displayed in a scrolling fashion. The message being displayed depends on whether the ACW system is processing a transaction, and if Custom External Display Messages have been programmed. First, in the case of processing a customer transaction, the External Display will exactly duplicate the messages shown on the ACW Controller. For example, messages such as "Deposit $4.00 WASH & WAX", "Credit $1.00", and "Thank You! Please Drive Ahead" will be displayed. These messages help the customer to follow the transaction and understand what is to be done. When there are no transactions being processed the messages displayed on the External Display will depend on whether any Custom External Display Messages have been programmed (instructions on how to program Custom External Display Messages are shown on page 8 of this manual). If all Custom External Display Messages have been programmed to "NOT USED ", the External Display will show the same messages as the ACW Controller's Welcome Messages. If there are any Custom External Display Messages programmed and set to be displayed (any message not set to "NOT USED" will be displayed), these messages will be shown during this idle period. Up to 4 different messages of 40 characters each can be programmed. If more than one External Display Message is programmed and displayed, the External Display will show each 40-character message for approximately 12 seconds then display the next message. Twelve seconds allows each 40-character message to be scrolled across the display approximately two times. This continues until all programmed messages have been displayed and the cycle repeats. Document #101-0036 12 03/20/06 IV. PROGRAMMING
To program Custom External Display Messages, starting from the RUN MODE, press the ACTION button to enter the MENU MODE. Using the RED and BLUE buttons, scroll through the categories until "EXT DISPLAY MSGS?" is displayed. Enter the PROGRAMMING MODE by pressing the ACTION BUTTON. The display will read: MSG #1 1st HALF Briefly, then NOT USED The second message displayed is the first 20 characters of the current external display message #1. To change this message, use the RED and BLUE buttons to toggle between "NOT USED" and the current custom message. When the desired message is displayed you may either program the next 20 characters of the message or exit the PROGRAMMING MODE. Repeatedly pressing the ACTION button scrolls through each of the 8 message halves (4 messages programmed 20 characters at a time). Pressing the RETURN button exits you from the PROGRAMMING MODE and into the MENU or RUN MODE. If the current custom message is blank or needs to be changed, it is possible to program the custom message using the following procedure. Starting from the RUN MODE, enter the PROGRAMMING MODE by pressing the ACTION button to enter the MENU MODE. Then scroll through the categories until "EXT DISPLAY MSGS" is displayed and again press the ACTION button. This will bring up the external display message #1 first 20 characters. If the current message is shown as "NOT USED", press the RED or BLUE buttons to display the current message. Press and hold the ACTION button until a flashing cursor is displayed, then release the ACTION button. Use the RED and BLUE buttons to move through the displayable letters and characters. Once the desired character or letter is displayed, move to the next space by pressing the ACTION button. When the message is complete, press the RETURN button to return to the MENU or RUN MODE. Document #101-0036 13 03/20/06 V. TROUBLESHOOTING
P R OB L E M / TEST
D is pla y d o e s n o t s h o w v e r s io n in fo r m a t io n ju s t a f t e r po w e r -u p. POS IT IV E / YES
If electrical test is positive, replace/reconnect Display and retest. If this does not correct the problem, then reconnect all the wires between the green 10-pin connector and the Terminal Block and retest. NE GAT IV E / NO
If electrical test is negative, proceed to the next test. Verify proper connection of Display Communication Harness. Verify proper connection of Display Transformer Harness. Verify power is connected to machine and circuit is energized. Perform the following electrical test: Test the voltage between terminals 6 & 7 of Display Terminal Block for 24VAC. Test the voltage between terminals 3 & 4 of square 4pin connector and terminal block of Display Transformer Harness for 24VAC. Test the voltage between terminals 1 & 2 of square 4pin connector of Display Transformer Harness for 120VAC. Test the voltage between terminals 1 & 5 of 12-pin connector of display Transformer Harness plugged into Main System Harness for 120VAC. If electrical test is positive, replace/reconnect Display Transformer Harness and retest. If electrical test is negative, proceed to the next test. If electrical test is positive, replace/reconnect Display Transformer Assembly and retest. If electrical test is positive, replace/reconnect Display Transformer Harness and retest. If electrical test is negative, proceed to the next test. If electrical test is negative, Refer to the troubleshooting section of the ACW or Auto-Tec Manual. Document #101-0036 14 03/20/06 PR OB L E M / TEST
D is pla y s h o w s v e r s io n a t po w e r u p, bu t t h e n r e m a in s bla n k . POS IT IV E / YES
If any information is displayed on the External Display, then verify that one of the following is true: At least one custom message half, set to a message other than "NOT USED", contains characters other than blank spaces. If all External Display messages are set to "NOT USED", at least one of the ACW Controller Welcome Messages must contain characters other than blank spaces. If either +12VDC or ­12VDC is obtained, then proceed to Test A. If either +12VDC or ­12VDC is obtained, replace/reconnect the Display Assembly and retest. If either +12VDC or ­12VDC is obtained, replace/reconnect the Display Communications Harness and retest. NE GAT IV E / NO
If no information is displayed on the External Display, proceed to the next test. Verify proper connection of Display Transformer Harness. Verify proper connection of Display Communication Harness. Verify serial communications by pressing a wash selection button to see if any information is displayed on the External Display. Test the voltage between terminals 8 & 9 of Display Terminal Block for +12VDC or ­12VDC. If not, proceed to Test B. A) Test the voltage between
terminals 8 & 9 of the green 10-pin connector for +12VDC or ­12VDC. If not, reconnect all the wires between the Terminal Block and the green 10-pin connector and retest. If not, proceed to the next test. terminals 2 & 3 Of the Display Communications Harness 4-pin connector for +12VDC or ­12VDC. Test the voltage between terminals 19 & 16 of the 22pin edge connector at the top of the ACW Controller (with the harness plugged in) for +12VDC or ­12VDC. B) Test the voltage between If either +12VDC or ­12VDC is obtained, replace/reconnect the Display Communications Harness and retest. If not, replace/reconnect the ACW Controller and retest. Document #101-0036 15 03/20/06 P R OB L E M / TEST
DI S P L A Y S H OW S ME S S AG E S WH IL E IN S T A N DB Y . POS IT IV E / YES
If yes, verify that at least one custom message half, set to a message other than "NOT USED", contains characters other than blank spaces. If the messages displayed are different than the ACW Welcome Messages but still not correct, refer to the programming section of this manual. NE GAT IV E / NO
If no, verify that all External Display Messages are set to "NOT USED" and at least one of the ACW Controller Welcome Messages contains characters other than blank spaces. For information on programming ACW Welcome Messages, refer to the programming section of the ACW Manual. Are the desired messages different than the ACW Controllers Welcome Messages? H OP P E R MAL F U NC T IONS W H E N DIS P L A Y T R AN S F OR ME R HAR NE S S I S IN S T A L L E D. Verify proper connection of Display Transformer Harness. Verify proper connection of Display Communications Harness. Verify correct ACW system operation by removing the Display Transformer Harness, reconnecting the system as before, and testing for proper Hopper operation. If ACW is operating correctly, replace/reconnect the Display Transformer Harness. If the ACW is not operating correctly, refer to the troubleshooting section of the ACW Manual. Document #101-0036 16 03/20/06 LIMITED WARRANTY AGREEMENT HAMILT MANUFA CORP. OF HAMILTON MANUFA CTURING CORP.
Hamilton Manufacturing Corp., an Ohio Corporation, ("Seller") warrants to Purchaser that all new equipment shall be free from defects in material and factory workmanship for a period of one (1) year from the original shipping date. Hamilton Manufacturing Corp. further warrants if any part of said new equipment in Seller's sole opinion, requires replacement or repair due to a defect in material or factory workmanship during said period, Seller will repair or replace said new equipment. Purchaser's remedies and the liabilities and obligations of Seller herein shall be limited to repair or replacement of the equipment as Seller may choose, and Seller's obligation to remedy such defects shall not exceed the Purchaser's original cost for the equipment. Purchaser EXPRESSLY AGREES this is the EXCLUSIVE REMEDY under this warranty. There are no other express or implied warranties which extend beyond the face hereof. All warranty repair service must be performed by either a Factory Trained Service Representative or HAMILTON MANUFACTURING CORP., 1026 Hamilton Drive, Holland, Ohio 43528 PHONE (419) 867-4858 or (800) 837-5561, FAX (419) 867-4867. The limited warranty for new equipment is conditioned upon the following: 1. 2. 3. 4. 5. 6. 7. 8. The subject equipment has not, in the Seller's sole opinion, been subjected to: accident, abuse, misuse, vandalism, civil disobedience, riots, acts of God, natural disaster, acts of war or terrorism. The Seller shall not be liable for any expense incurred by Purchaser incidental to the repair or replacement of equipment and Purchaser shall assume full responsibility for any freight or shipping charges. The coverage of this warranty shall not extend to expendable parts. Purchaser shall have a warranty registration card on file with Seller prior to any claim in order for warranty protection to apply. No warranty coverage is applicable to any equipment used for currency other than that specified at the time of the purchase. Seller expressly disclaims any warranty that counterfeit currency will not activate said equipment. Seller expressly disclaims any warranty for any losses due to bill manipulation or theft or loss of cash under any circumstances. Use of the equipment for anything other than its intended and designed use will void the Limited Warranty Agreement. Use of equipment for anything other than its intended and designed use includes, but is not limited to, downloading software/applications not certified by Seller such as e-mail, spyware, screen savers, viruses, worms, third party software, web search engines, cookies, spam, desktop applications, games, web surfing, etc. Seller further warrants all repair or service work performed by a factory trained representative or Hamilton Manufacturing Corp. for a period of ninety (90) days from the date the repair or service work was performed. Purchaser's remedies and the liabilities and obligations of Seller herein shall be limited to repair or replacement of equipment as Seller may choose, and Seller's obligation to remedy such defects shall not exceed the Purchaser's depreciated value of the equipment. Purchaser EXPRESSLY AGREES this is an EXCLUSIVE REMEDY under this warranty. There are no other express or implied warranties on repair or service work performed by a factory trained representative or Hamilton Manufacturing Corp. which extend beyond the face hereof.
Document #101-0036 17 03/20/06 The limited warranty for repair and service work is conditioned upon the following: 1. 2. 3. 4. 5. 6. 7. 8. 9. The subject equipment has not, in the Seller's sole opinion, been subjected to: accident, abuse, misuse, vandalism, civil disobedience, riots, acts of God, natural disaster, acts of war or terrorism. The Seller shall not be liable for any expense incurred by Purchaser incidental to the repair or replacement of equipment and Purchaser shall assume full responsibility for any freight or shipping charges. The coverage of this warranty shall not extend to expendable parts. Purchaser shall have a warranty registration card on file with Seller prior to any claim in order for warranty protection to apply. No warranty coverage is applicable to any equipment used for currency other than that specified at the time of the purchase. Seller expressly disclaims any warranty that counterfeit currency will not activate said equipment. Seller expressly disclaims any warranty for any losses due to bill manipulation or theft or loss of cash under any circumstances. No person or entity other than a factory trained representative or Hamilton Manufacturing Corp. has performed or attempted to perform the subject repair or service. Using equipment which has been serviced or repaired for anything other than its intended or designed use such as downloading software applications not certified by Seller will void the Limited Warranty Agreement. This includes software/applications such as e-mail, spyware, screen savers, viruses, worms, third party software, web search engines, cookies, spam, desktop applications, games, web surfing, etc. THIS AGREEMENT IS MADE WITH THE EXPRESS UNDERSTANDING THAT THERE ARE NO IMPLIED WARRANTIES THAT THE EQUIPMENT SHALL BE MERCHANTABLE, OR THAT THE GOODS SHALL BE FIT FOR ANY PARTICULAR PURPOSE. PURCHASER HEREBY ACKNOWLEDGES THAT IT IS NOT RELYING ON THE SELLER'S SKILL OR JUDGMENT TO SELECT OR FURNISH EQUIPMENT SUITABLE FOR ANY PARTICULAR PURPOSE AND THAT THERE ARE NO WARRANTIES WHICH EXTEND BEYOND THAT WHICH IS DESCRIBED HEREIN. The Purchaser agrees that in no event will the Seller be liable for direct, indirect, or consequential damages or for injury resulting from any defective or non-conforming new, repaired or serviced equipment, or for any loss, damage or expense of any kind, including loss of profits, business interruption, loss of business information or other pecuniary loss arising in connection with this Limited Warranty Agreement, or with the use of, or inability to use the subject equipment regardless of Sellers knowledge of the possibility of the same. Document #101-0036 18 03/20/06 Document #101-0036 19 03/20/06 Hamilton Manufacturing Corp.
1026 Hamilton Drive Holland, OH 43528 Sales Phone: (888) 723-4858 Sales Fax: (419) 867-4850 Customer Service Phone: (800) 837-5561 Customer Service Fax: (419) 867-4857 Parts Phone: (866) 835-1721 Parts Fax: (419) 867-4867 Website: http://www.hamiltonmfg.com Email Addresses: service@hamiltonmfg.com sales@hamiltonmfg.com parts@hamiltonmfg.com info@hamiltonmfg.com
Document #101-0036 20 03/20/06