ight>

AP/CP PRECUT SAUNA ROOM BUILDING INSTRUCTIONS


AP/CP PRECUT SAUNA ROOM BUILDING INSTRUCTIONS


In preparation for your package, you have insulated the walls and ceiling (between studs) with 3 1/2" Owens Corning
Fiberglas with foil back and applied Reynolds Type C Construction foil on walls and ceiling (stapled over studs):

1.
Boards are cut to size for walls and ceiling.

2.
Precut ceiling boards have a single dot (colored) at ends, indicating that ceiling should be installed first.

3.
Dots at ends of wall boards indicate which wall should be paneled first, etc. Back wall has two dots (should go next after
ceiling), right wall has three dots, left wall has four dots, and front wall is marked with right or left.

4.
Sort wall boards for appearance, use best boards above bench level; others below bench level.

5. As you start first board (no. 1 back board) raise it 3/4" from floor and level it. Blind nail it to wall through tongue of
board with 5p hot dipped, galvanized nails provided. Then take one board from right wall (3 dots) and raise it from
floor so that V-joint is even with back wall board V-joint. Level it and place chisel or bar between front wall & right
wall board which you are installing and apply pressure toward back wall so that it will fit tightly to back wall.

6.
Follow same steps (as above) for left hand wall boards (four dots).

7. After nailing each starter board for one complete layer around room, follow same steps layer by layer continuing to use
chisel for tight fit, until reaching the last board. Rip each of the last boards for tight fit to ceiling.

8.
After paneling room, install crown ceiling molding (ceiling) 3/4" x 3/4" (which you will cut to size). Ceiling moldings are
3/4" x 3/4" and should be glued and nailed; base is 1" x 2" and should be nailed only. Apply silicone caulking between
base and your floor surface

9.
Install benches as shown on drawings.

10. Install door. Seal entire door, inside & outside, (except for glass) with non-toxic clear sealer (eg. Thompsons Waterseal).

11. Install Sauna heater by referring to information in wiring diagram provided with heater. Fill with stones provided (hose
stones with water to clean first). Pack stones loosely between elements and on top until elements are completely covered;
You may not need them all.

12. Install guard rail around heater with wood screws provided (see sketch).

13. Install lower vent in lower area of room (most desirable location is below heater) 6" from floor.

14. Install upper vent in any area from below upper bench to within 6" from ceiling, DO NOT vent to air outside of
building, only to adjacent spaces outside Sauna.

15. Hang thermometer 6" from ceiling, directly above Sauna heater, and hang bathing sign on exterior front wall. Warning
signs should be placed above heater.

16. Now you are ready for electrical hookup. (This should be provided by a qualified electrician as per wiring instructions
provided with heater.)

NOW YOU CAN ENJOY YOUR SAUNA!

2 Sided Heater Guard Install



Instructions: Turn the two T-Bars upside down exposing the grooves cut into the
bottom side of the guardrail. Place the two 45-degree angles together to form one
90-degree angle. Insert the "Hoffman" Locking Key into the grooves of the two
pieces. Place the two pieces on a clean flat surface, using a hammer force the
Locking Key into the two grooves until it is flush with the wood surface. Turn the
guardrail over so that the Locking Keys face the floor. After the heater is mounted,
install the guardrail flush with the top of the heater casing. Use the wood screws
provided, then insert the wood screw caps in the hole (do not use glue).

3 Sided heater guard install

Instructions: Turn the two T-Bars and Center I-Beam upside down exposing the
grooves cut into the bottom side of the guardrail. Starting with the Center I-Beam
and either the left or right T-Bar place the two 45-degree angles together to form
one 90-degree angle. Insert the "Hoffman" Locking Key into the grooves of the
two pieces. Place the two pieces on a clean flat surface, using a hammer force the
Locking Key into the two grooves until it is flush with the wood surface. Repeat
this step with the second T-Bar. Turn the guardrail over so that the Locking Keys
face the floor. After the heater is mounted, install the guardrail flush with the top
of the heater casing. Use the wood screws provided, then insert the wood screw
caps in the hole (do not use glue).