cellpadding=10 cellspacing=0 width=100%>Yahoo! is not affiliated with the authors of this page or responsible for its content.
Doc100-004-A_OP-AXE-Mini-Man www.alltraxinc.com
AXE
Mini-Manual
For Golf Car Applications
Alltrax, Inc., (hereafter Alltrax) warrants that the
product purchased is free from defects in materi-
als or workmanship for a period of
2 years
from
the date of manufacture. This warranty does not
apply to defects due directly or indirectly to mis-
use, abuse, negligence, accidents, repairs, or al-
terations. Alltrax, Inc., shall in no event be
liable for death, injuries to persons or prop-
erty, or for incidental, contingent, or conse-
quential damages arising through the use of
our products.
Alltrax assumes no liability for applications assis-
tance or customer product design. Customers are
responsible for products and applications using
Alltrax products. Customers should provide ade-
quate design and operating safeguards.
Alltrax specifically disclaims the implied warranties
of merchantability and fitness for a particular pur-
pose. However, some states do not allow limita-
tions on how long an implied warranty lasts, so
the preceding exclusion may not apply to you.
This is Alltrax Inc.s, sole written warranty. No
other warranty is expressed or implied.
In the event you should need warranty repair,
call Alltrax at (541) 476-3565. Products or parts
shipped by Customer to Alltrax must be sent post-
age paid and packaged appropriately for safe
shipment. Alltrax is not responsible for Customer
products received without warranty service au-
thorization and may be rejected.
Alltrax reserves the right to repair or replace mer-
chandise at its option and reserves the right to
make changes to any of its products or specifica-
tions without notice.
LIMITED WARRANTY
A n E n g i n e e r e d S o l u t i o n
LED Status Indicator
LED Blink Codes:
At power up, # of green blinks indicates
configured throttle type:
1 Green = 0-5k-ohm
2 Green = 5k-0-ohm
3 Green = 0-5 Volt
4 Green = EZ-GO inductive (ITS)
5 Green = Yamaha 0-1K
6 Green = Taylor-Dunn 6-10.5V
7 Green = CLUBCAR 5K-3-wire
Normal display status:

Solid Green: Controller ready to run
Solid Red: Controller in programming mode
Solid Yellow: Controller throttle is wide
open, controller is supplying max output,
and is not in current limit.
Trouble Shooting
Error code display:# of RED blinks
indicates any error conditions that might
exist:
1 Red = Throttle Position Sensor Over
Range. Check for open wires.
2 Red = Under Temperature. Controller
below -25C
3 Red = HPD. Throttle hasn't gone to
zero during this power on cycle.
4 Red = Over Temperature. Controller
over 95C
5 Red = unused
6 Red = Battery Under Voltage detected.
Battery V < under voltage slider
7 Red = Battery Over Voltage detected.
Battery V > over-voltage slider
Doc100-004-A_OP-AXE-Mini-Man.pub, 6-15-2006
Alltrax, Inc.
1111 Cheney Creek Rd
Grants Pass, OR. 97527
Phone: 541-476-3565
Fax: 541-476-3566

Programmable

300, 400, 500, & 650
Amp

12 to 72 Volt DC

Plug Brake Option

For Series Wound
Motors Club Car & E-Z-GO
Wiring Diagrams
Not all controllers use the A2 terminal. If not, bolt
the two wires together, insulate with tape or heat
shrink, then secure in safe location.
ControllerPRO
ControllerPRO is free user friendly software for cus-
tomizing your Alltrax AXE Controllers. Download
your copy of ControllerPRO from :
www.alltraxinc.com
Configuration
WARNING: Disconnect all battery charging
sources while programming your AXE controller.
The controllers RS-232 serial port is referenced to
the B- battery connection. Beware of any possi-
ble ground loop faults between your com-
puter and the controller which could damage
both the AXE Controller and PC, or cause per-
sonal injury.

Hardware: Use a STRAIGHT-THROUGH DB-9 pin /
RS-232 serial interface cable to connect the control-
ler to the PC. Alternatively use the preferred DB-9
pin RS-232 serial port to USB adapter.
The AXE controller must be powered before the
ControllerPRO program will have any effect. Before
programming the AXE, READ THE SAFETY

NOTES BELOW. For bench programming prior to
installation, a fused 18V or higher battery may be
used to power the controller. Connect battery nega-
tive to the B- bus bar, battery positive to pin 1.
If you see an error Motor Controller is Not
Responding, verify the controller is powered up
and the connections are inserted correctly. If the
error message continues, uninstall then reinstall the
drivers for the communications cable. If the prob-
lem persists, contact Alltrax Technical Support.
Safety Notes:
Alltrax recommends that all motor controller
applications have a fuse in the battery circuit.
Many vehicles do not have a fuse, and will
need to have one installed. The following fuses
manufactured by Bussman or Littelfuse are
acceptable: For controllers rated at 400 amps
or less use ANN250. On controllers rated at
450 amps or more use ANN400. [See:
Doc100-016-A_OP-Fuse-Install-Guide.doc]
Alltrax also recommends a diode across the coil
of the solenoid if it is not already installed. A
minimum of a 100V 1A diode (a 1N4004 is suit-
able) is required. See complete wiring diagrams
for orientation.
Working on electric vehicles, sudden unex-
pected events can occur, its recommended to:

Place the drive axle on jack stands
wheels off the floor

When working on wiring or batteries, al-
ways remove rings and watches

Use the proper safety equipment, eye pro-
tection, and insulated tools

Never connect a computer while the vehi-
cle is being charged

Disconnect batteries before installing or
working on the controller
For complete instructions and wiring
diagrams for other configurations and
vehicles, please download our AXE
Manual from www.alltraxinc.com
Alltrax, Inc.
1111 Cheney Creek Rd
Grants Pass, OR. 97527
Phone: 541-476-3565
Fax: 541-476-3566
1 2 3
4
RED
GRN
YEL
NOT USED
B-
M-
B+
YELLOW
GREEN
BLUE
PUR
RED/WHT
BLK
1
2 3 4
RED
BLK
WHT
ORG
M-
A2
A2
Optional
B+
Motor A1 (1204/1205 Replacement)
Switch A (1206 Replacement)
BATTERY +
* F-N-R Terminal C (1204/1205 Replacement)
* Motor A1 (1206 Replacement)
B-
BATT
(-)
BLK
SOLENOID BLK
FUSE
BATT
(-)
BLK
FUSE
LED
LED
QUICK INSTALLATION GUIDE
KEY SWITCH
THROTTLE
THROTTLE
KEY SWITCH
THROTTLE
THROTTLE
1/2 SPD RVRS