bushing, making sure to move the
cam in the desired direction.
Tighten bolts and center punch
three places on front face of gear
1/16" from edge of bushing hole to
prevent bushing from vibrating
out. A 0° bushing is also supplied
so stock timing setup can be used
again after the gear has been
drilled. These offset bushings are
rated in CRANKSHAFT degrees.
The five bushings are stamped
with the amount of offset in crank-
shaft degrees.
Installation Instructions
Camshaft Timing Offset
Bushing Kit
For more information, see www.cranecams.com
16G
4/00
CRANE CAMS, INC. 530 Fentress Blvd., Daytona Beach, FL 32114
Tech Line: (386) 258-6174
www.cranecams.com
Fax: (386) 258-6167
Fits all Chevrolet V8's 262 thru
400, 348-409, and 396-402-427-
454 Cu.In.
Also, Chrysler "B"
wedge engines and 426 Hemi
engines.
Installation Instructions
Camshaft timing gear must be
removed from engine. Place gear
with bolt head side down on drill
table. Drill all four holes (3 bolt
holes and dowel hole) all the way
through with a 13/32" drill.
After drilling four holes, remove
burrs and place gear on camshaft
in normal manner. Install bolts fin-
ger tight.
Install offset degree
bushing, making sure to move the
cam in the desired direction.
Tighten bolts and center punch
three places on front face of gear
1/16" from edge of bushing hole to
prevent bushing from vibrating
out. A 0° bushing is also supplied
so stock timing setup can be used
again after the gear has been
drilled. These offset bushings are
rated in CRANKSHAFT degrees.
The five bushings are stamped
with the amount of offset in crank-
shaft degrees.
Installation Instructions
Camshaft Timing Offset
Bushing Kit
For more information, see www.cranecams.com
16G
4/00
CRANE CAMS, INC. 530 Fentress Blvd., Daytona Beach, FL 32114
Tech Line: (386) 258-6174
www.cranecams.com
Fax: (386) 258-6167
Fits all Chevrolet V8's 262 thru
400, 348-409, and 396-402-427-
454 Cu.In.
Also, Chrysler "B"
wedge engines and 426 Hemi
engines.
Installation Instructions
Camshaft timing gear must be
removed from engine. Place gear
with bolt head side down on drill
table. Drill all four holes (3 bolt
holes and dowel hole) all the way
through with a 13/32" drill.
After drilling four holes, remove
burrs and place gear on camshaft
in normal manner. Install bolts fin-
ger tight.
Install offset degree
bushing, making sure to move the
cam in the desired direction.
Tighten bolts and center punch
three places on front face of gear
1/16" from edge of bushing hole to
prevent bushing from vibrating
out. A 0° bushing is also supplied
so stock timing setup can be used
again after the gear has been
drilled. These offset bushings are
rated in CRANKSHAFT degrees.
The five bushings are stamped
with the amount of offset in crank-
shaft degrees.
Installation Instructions
Camshaft Timing Offset
Bushing Kit
For more information, see www.cranecams.com
16G
4/00
CRANE CAMS, INC. 530 Fentress Blvd., Daytona Beach, FL 32114
Tech Line: (386) 258-6174
www.cranecams.com
Fax: (386) 258-6167
Fits all Chevrolet V8's 262 thru
400, 348-409, and 396-402-427-
454 Cu.In.
Also, Chrysler "B"
wedge engines and 426 Hemi
engines.
Installation Instructions
Camshaft timing gear must be
removed from engine. Place gear
with bolt head side down on drill
table. Drill all four holes (3 bolt
holes and dowel hole) all the way
through with a 13/32" drill.
After drilling four holes, remove
burrs and place gear on camshaft
in normal manner. Install bolts fin-
ger tight.
Install offset degree
bushing, making sure to move the
cam in the desired direction.
Tighten bolts and center punch
three places on front face of gear
1/16" from edge of bushing hole to
prevent bushing from vibrating
out. A 0° bushing is also supplied
so stock timing setup can be used
again after the gear has been
drilled. These offset bushings are
rated in CRANKSHAFT degrees.
The five bushings are stamped
with the amount of offset in crank-
shaft degrees.
Installation Instructions
Camshaft Timing Offset
Bushing Kit
For more information, see www.cranecams.com
16G
4/00
CRANE CAMS, INC. 530 Fentress Blvd., Daytona Beach, FL 32114
Tech Line: (386) 258-6174
www.cranecams.com
Fax: (386) 258-6167