he job in a fraction of the time
required for serving with waste strand,
and leave no protruding ends. They
are pre-shaped and easily closed with
pliers.
GROUND WIRE CLIPS
These are easy-to-install clips for
securely fastening ground wires to
poles and crossarms. Make high
pressure, large area contact with
the ground wire and prevent radio
interference producing static discharges.
Ground wire clips are quickly installed
by driving one nail and bending the tail
back over the nail head, as illustrated.
Copperweld nails are recommended
for copper clips.
Line Accessories
Wire Clips, Grips and Grounding Lugs
Electrical Apparatus
K-SEC 160
1
September 2000 New Issue
Printed in U.S.A.
Strand Size
Catalog Number
(Inches)
Aluminum
Plated Steel
.3125
36
336
.3750
37
337
.4375
38
338
TABLE 2
Ordering Information
TABLE 3
Ordering Information
Ground Wire
Catalog
Material
Maximum Size
Number
Plated Steel
4 Sol.
5730
Copper 4
Sol.
5730-1
Aluminum
4 Sol.
5730-2
Aluminum
1/0 Sol.
106425
Copperweld Nails
8d2.5" x .0625" 64110-41
Figure 2.
Guy Wire Clip.
Figure 3.
Ground Wire Clips.
TABLE 1
Ordering Information
Dimensions
Ground Wire
Catalog
Material
(Inches)
Maximum Size
Number
Bronze
.625 x 2.5
4 Str.
12325
Bronze
.625 x 2.875
1/0 Str.
12325-1
Zinc-Plated
.625 x 2.5
4 Str.
12326
Steel
.625 x 2.875
1/0 Str.
12326-1
Figure 1.
Non-Static Ground Wire Clips. LAY-CIT CABLE GRIPS
Contoured plates securely grip either
round or oval cable without damaging
the insulation. Holding pressure is
evenly distributed over a large area,
and is proportional to conductor
tension. The plates are aluminum,
4" long and have knurled inner sur-
faces for high holding power, even on
synthetic jacketed cables. They are
easily installed on continuous runs by
removing the flexible cable bail from
the side hooks on the plates.
T-BOLT GROUNDING LUG
This is a heavy-duty lug for connecting
ground wires to transformers or steel
structures. The threaded stud fits all
standard transformer tapped grounding
pads. High clamping force prevents
the wire from pulling out. The wire may
be run 90° from position illustrated.
1
/
2
" - 13 THREADED
GROUNDING LUG
A heavy-duty lug for connecting ground
wires to electrical equipment such as
transformers or steel structures. The
1
/
2
" - 13 threaded stud fits all EEI-NEMA
distribution equipment. It is installed
with a standard
3
/
4
" socket wrench.
This connector is machined from solid
300 Series stainless steel and has an
industry standard
5
/
16
" hex socket set
screw to secure the ground conductor.
RUST CUTTER
Rust cutter loosens rusted or corroded
nuts and bolts in seconds. Saves time,
labor and inconvenience of sawing off
corroded fastenings. Rust cutter spray
reaches otherwise inaccessible rusted
areas. Harmless to skin. Packed in 5
ounce pressurized cans. No fluoro-
carbons.
Wire Clips, Grips and Grounding Lugs
2
P.O. Box 1640
Waukesha, WI 53187
www.cooperpower.com
Printed on Recycled Paper
© 2000 Cooper Industries, Inc.
Kearney is a trademark of Cooper Industries, Inc.
MI
9/00
Figure 7.
Rust Cutter.
Figure 6.
1
/
2
"-13 Threaded Grounding Lug.
Catalog
Quantity
Number
Case of 24 cans
19229-1
TABLE 7
Ordering Information
Catalog
Wire Range
Number
#10 Solid to 2/0 Stranded
GL01X20SS
0.102" to 0.419"
TABLE 6
Ordering Information
Note: Sold by case only.
Stud Wire Catalog
Material
Size
Size Number
Plated Bronze
1
/
2
"-13 x
3
/
8
"
6 Sol. 17546-2
to 1 Str.
TABLE 5
Ordering Information
Figure 5.
T-Bolt Grounding Lug.
Figure 4.
Lay-Cit Cable Grips.
Round
Oval
Cable
Cable
Dia. (in.)
Dia. (in.)
Catalog
Max. Min.
Max.
Min.
Number
.625 .375 .390 x .306
.344 x .5
19234
1.125 .625 .672 x 1.047 .391 x .656 19235
TABLE 4
Ordering Information