=black height=1 colspan=2>
TRA-BOND FS12 TRA-BOND FS12
FAST CURE EPOXY ADHESIVE SYSTEM
PROPERTY
TYPICAL VALUES
TRA-BOND FS12 is an epoxy resin formulation developed for room temperature bonding applications
where a fast cure epoxy adhesive is needed. This effectie epoxy formulation consists of 100% reactive
materials (contains no solvents) and it is recommended for structural and electric repairs, traffic bar and
reflector bonding, gel coats, and for similar field kit applications where the combination of fast cure with
superior physical properties is required. TRA-BOND FS12 readily bonds to itself and to most metals,
glass, wood ceramics, many plastics, and other materials. The fully cured adhesive is an electrical
insulator, and in addition provides excellent resistance to weather, water, gases, petroleum solvents and
fuels, salt solutions, mild acids and alkalis, and many other organic and inorganic compounds.

www.tra-con.com
Amber
Color
1.130
Specific gravity, mixed
-50 to 110
Operating temperature range, °C
82
Hardness, Shore D
5.50E-05
Coefficient of expansion, cm/cm/°C
4.27
Dielectric constant
1 KHz @ 25°C
0.030
Dissipation factor
1 KHz @ 25°C
4.20E+14
Volume resistivity, ohm-cm @ 25°C
10,200
Compressive strength, psi, °C
77
Heat distortion temperature, °C
CURE SCHEDULE
5 minutes
POT LIFE
48 hours @ 25°C or
1 hour @ 25°C
2 hours @ 65°C
Revision: A
Print Date: 8/13/01
TRA-CON, INC. 45 Wiggins Avenue, Bedford, MA 01730 800-TRA-CON1 (800-872-2661) Tel. (781) 275-6363 FAX (781)275-9249
QAF-1057 Rev B
Revision Date: 6/1/90 APPLICATION DIRECTIONS
(1) Carefully clean and dry all surfaces to be bonded.
(2) Remove clamp and thoroughly mix the TRA-BOND FS12 epoxy adhesive system components in the handy
BIPAX mixing-dispenser package until color is uniform throughout.
(3) Apply this completely mixed adhesive to the prepared surfaces, and gently press these surfaces together. Contact
pressure is adequate for strong, reliable bonds -- however maintain contact until adhesive is completely cured.
WARNING: TRA-BOND FS12 is a high exotherm epoxy adhesive. USE IMMEDIATELY AFTER MIXING.
Uncured epoxy adhesives - consisting of resin and hardener components - may cause dermatitis, skin sensitization or other allergic responses. Prevent all
open flame. KEEP OUT OF REACH OF CHILDREN. Immediately clean up any spills that may occur.
TRA-BOND FS12
WARNING: THIS MATERIAL IS SOLD FOR INDUSTRIAL USE ONLY
TRA-CON resin products are marked with an expiration date at the time of manufacture which is similar to the the
dating system used for most perishable materials such as foodstuffs, photographic films, pharmaceuticals and most
reactive products. This date is marked "Use Before" which indicates that the product will yield its best properties
when mixed and cured before the date shown. The expiration date should be monitored to ensure that inventory
levels are replenished in adequate time to avoid unnecessary interruptions in the manufacturing process.
The expiration date is based upon dry storage conditions at or below 80°F (27°C) in the original, sealed and unopened
containers for BIPAX, TRA-PAX and bulk packaged materials. The expiration date for pre-mixed and frozen materials
is based upon dry storage conditions at or below the temperature indicated on each package. Contents may separate
during storage. Resin or hardener in bulk containers (e.g. quarts, gallons) should be thoroughly mixed prior to
combining them to obtain all the benefits of the properties designed into the formulation.
Some ingredients in this formulation provided in BIPAX, TRA-PAX and bulk packaging may crystallize when
subjected to low temperature storage. Merely returning the product back to room temperature will not always
redissolve the crystals and a gentle warming cycle of 125°F for 30 minutes prior to mixing the resin and hardener
components may be necessary to return the product to its best condition. Crystallized epoxy components do not react
as well as liquid components and should be redissolved prior to use for best results.
The properties given are TYPICAL VALUES and are not intended for use in preparing specifications.
Users should make their own tests to determine the suitability of this product for their own purposes.
TRA-CON, INC. MAKES NO EXPRESS OR IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS OR OTHERWISE with respect to its
products. In addition, while the information contained herein is believed to be reliable, no warranty is expressed or implied regarding the accuracy of the
data or the results to be obtained from the use thereof. All recommendations or suggestions for use are made without guartanee inasmuch as conditions
of use are beyond our control.
AVAILABILITY
EXPIRATION DATE
STORAGE AND HANDLING CONDITION
Please contact TRA-CON's technical service department at 800-TRA-CON1 for packaging options for this material
that will best suit your process.
Revision: A
Print Date: 8/13/01
TRA-CON, INC. 45 Wiggins Avenue, Bedford, MA 01730 800-TRA-CON1 (800-872-2661) Tel. (781) 275-6363 FAX (781)275-9249
QAF-1057 Rev B
Revision Date: 6/1/90