« back to results for ""
Below is a cache of http://www.swapca.org/regs/reg493.pdf. It's a snapshot of the page taken as our search engine crawled the Web.
The web site itself may have changed. You can check the current page or check for previous versions at the Internet Archive. Yahoo! is not affiliated with the authors of this page or responsible for its content.
SWAPCA 493 VOC AREA SOURCE RULES SWAPCA 493
VOC AREA SOURCE RULES
Effective May 25, 1996 SWAPCA 493
VOC AREA SOURCE RULES
Section
Page
Consumer Products
493-100
Consumer Products (Reserved)
1
Spray Paints
493-200-010
Applicability
1
493-200-020
Definitions
1
493-200-030
Spray Paint Standards and Exemptions
6
493-200-040
Requirements for Manufacture, Sale and
8
Use of Spray Paint
493-200-050
Recordkeeping and Reporting Requirements
9
493-200-060
Inspection and Testing Requirements
9
Architectural Coatings
493-300-010
Applicability
10
493-300-020
Definitions
11
493-300-030
Standards
17
493-300-040
Requirements for Manufacture, Sale and
21
Use of Architectural Coatings
493-300-050
Recordkeeping and Reporting Requirements
22
493-300-060
Inspection and Testing Requirements
23
Motor Vehicle Refinishing
493-400-010
Applicability
23
493-400-020
Definitions
23
493-400-030
Coating Standards and Exemptions
23
493-400-040
Requirements for Manufacture and
28
Sale of Coatings
493-400-050
Requirements for Motor Vehicle Refinishing
29
in Vancouver AQMA
493-400-060
Record Keeping and Reporting Requirements
30
493-400-070
Inspection and Testing Requirements
30
Area Source Common Provisions
493-500-010
Applicability
30
493-500-020
Compliance Extensions
31
493-500-030
Exemption From Disclosure to the Public
32
493-500-040
Future Review
32 SWAPCA 493
Effective May 25, 1996
VOC Area Source Rules
1
SWAPCA 493-100 - CONSUMER PRODUCTS
[Statutory Authority: Chapter 70.94.141 RCW, 70.94.145 RCW, 70.94.380 RCW and 70.94.395. Original adoption 96-10-026 filed 4/25/96, effective 5/26/96]
Reserved for adoption by reference of the U.S. Environmental Protection Agency's (EPA) equivalent
rule. The EPA proposed rule was published in the federal register on Tuesday, April 2, 1996; Federal
Register Vol. 61, No. 64, page 14531; 40 CFR 59, [AD-FRL-5451-7].
SWAPCA 493-200 - SPRAY PAINTS
SWAPCA 493-200-010 Applicability
[Statutory Authority: Chapter 70.94.141 RCW, 70.94.145 RCW, 70.94.380 RCW and 70.94.395. Original adoption 96-10-026 filed 4/25/96, effective 5/26/96]
(1)
SWAPCA 493-200-010 through 493-200-060 apply to any manufacturer, distributor, retailer
or commercial applicator of spray paint for sale or use in the Vancouver AQMA.
SWAPCA 493-200-020 Definitions
[Statutory Authority: Chapter 70.94.141 RCW, 70.94.145 RCW, 70.94.380 RCW and 70.94.395. Original adoption 96-10-026 filed 4/25/96, effective 5/26/96]
As used in SWAPCA 493-200:
(1)
"Adhesive"
means a product used to bond one surface to another.
(2)
"Anti-Static Spray"
means a product used to prevent or inhibit the accumulation of static
electricity.
(3)
"Art Fixative or Sealant"
means a clear coating, including art varnish, workable art fixative,
and ceramic coating, which is designed and labeled exclusively for application to paintings,
pencil, chalk, or pastel drawings, ceramic art pieces, or other closely related art uses, to provide
a final protective coating or to fix preliminary stages of art work while providing a workable
surface for subsequent revisions.
(4)
"ASTM"
means the American Society for Testing and Materials.
(5)
"Auto Body Primer"
means an automotive primer or primer surface coating designed and
labeled exclusively to be applied to a vehicle body substrate for the purpose of corrosion
resistance and building a repair area which can be sanded to a smooth condition after drying.
(6)
"Automotive Bumper and Trim Product"
means a product, including adhesion promoters
and chip sealants, designed and labeled exclusively to repair and refinish automotive bumpers
and plastic trim parts.
(7)
"Automotive Underbody Coating"
means a flexible coating which contains asphalt or rubber
and is labeled exclusively for use on the underbody of motor vehicles to resist rust, abrasion
and vibration, and to deaden sound.
(8)
"Aviation Propeller Coating"
means a coating designed and labeled exclusively to provide
abrasion resistance and corrosion protection for aircraft propellers.
(9)
"Aviation or Marine Primer"
means a coating designed and labeled exclusively to meet
federal specification TT-P-1757.
(10)
"Belt Dressing"
means a product applied on auto fan belts, water pump belting, power
transmission belting, industrial equipment belting, or farm machinery belting to prevent
slipping, and to extend belt life.
(11)
"Cleaner"
means a product designed and labeled primarily to remove soil or other
contaminants from surfaces.
(12)
"Clear Coating"
means a coating which is colorless, containing resins but no pigments, SWAPCA 493
Effective May 25, 1996
VOC Area Source Rules
2
except flatting agents, and is designed and labelled to form a transparent or translucent solid
film.
(13)
"Coating Solids"
means the nonvolatile portion of a spray paint, consisting of the film
forming ingredients, including pigments and resins.
(14)
"Complying Spray Paint"
means a spray paint which complies with the VOC content limits
in SWAPCA 493-100-020.
(15)
"Consumer"
means any person who purchases or acquires any spray paint for personal,
family, or household use. Persons acquiring a spray paint product for resale are not considered
consumers of that product.
(16)
"Commercial Applicator"
means any person who purchases, acquires, applies, or contracts
for the application of spray paint for commercial, industrial or institutional uses, or any person
who applies spray paint in the course of an activity from which compensation is derived.
(17)
"Corrosion Resistant Brass, Bronze, or Copper Coating"
means a clear coating formulated
and labeled exclusively to prevent tarnish and corrosion of uncoated brass, bronze or copper
metal surfaces.
(18)
"Distributor"
means any person who sells or supplies spray paint for the purposes of resale or
distribution in commerce. "Distributor" includes activities of a self-distributing retailer related
to the distribution of products to individual retail outlets. "Distributor" does not include
manufacturers except for a manufacturer who sells or supplies spray paint products directly to
a retail outlet. "Distributor" does not include consumers.
(19)
"Dye"
means a product containing no resins which is used to color a surface or object without
building a film.
(20)
"Electrical Coating"
means a coating designed and labeled to be used exclusively to coat
electrical components such as electric motor windings to provide electrical insulation or
corrosion protection.
(21)
"Enamel"
means a coating which cures by chemical cross-linking of its base resin and is not
resoluble in its original solvent.
(22)
"Engine Paint"
means a coating designed and labeled exclusively as such, which is used
exclusively to coat engines and their components.
(23)
"Environmental Protection Agency" or "EPA"
means the United States Environmental
Protection Agency.
(24)
"Exact Match Finish, Automotive"
means a topcoat which meets all of the following
criteria:
(a)
The product is designed and labeled exclusively to exactly match the color of an
original, factory-applied automotive coating during the touch-up of automobile
finishes;
(b)
The product is labeled with the original equipment manufacturer's name for which it
was formulated; and
(c)
The product is labeled with one of the following:
(1)
The original equipment manufacturer's (OEM) color code;
(2)
The color name; or
(3)
Other designation identifying the specific OEM color to the purchaser.
(d)
Notwithstanding subsections (a) through (c) of this section, automotive clear coatings
designed and labeled exclusively for use over automotive exact match finishes to
replicate the original factory applied finish shall be considered to be automotive exact
match finishes.
(25)
"Exact Match Finish, Engine Paint"
means a coating which meets all of the following SWAPCA 493
Effective May 25, 1996
VOC Area Source Rules
3
criteria:
(a)
The product is designed and labeled exclusively to exactly match the color of an
original, factory-applied engine paint;
(b)
the product is labeled with the original equipment manufacturer's name for which it was
formulated; and
(c)
the product is labeled with one of the following:
(1)
The OEM color code;
(2)
The color name; or
(3)
Other designation identifying the specific OEM color to the purchaser.
(26)
"Exact Match Finish, Industrial"
means a coating which meets all of the following criteria:
(a)
The product is designed and labeled exclusively to exactly match the color of an
original, factory-applied industrial coating during the touch-up of manufactured
products;
(b)
The product is labeled with the original equipment manufacturer's name for which it
was formulated; and
(c)
The product is labeled with