Repacking the Box
B-1
Cisco 10008 Router Hardware Installation Guide
OL-0659-13
A P P E N D I X
B
Repacking the Box
If your system is damaged, you must repack it for return shipment. Use the original shipping containers.
Figure B-1
shows an exploded view of the system and packing materials.
To return or move the Cisco 10008 router to a different location, follow these instructions for repacking
the system, using the original packaging material: B-2
Cisco 10008 Router Hardware Installation Guide
OL-0659-13
Appendix B Repacking the Box
Figure B-1
Cisco 10008 System and Packing Material
Step 1
Place the bottom packing material section inside the bottom of the shipping container.
Step 2
Use at least two people to place the Cisco 10008 chassis inside the container. Be sure that the chassis is
positioned correctly before you lower it inside the container (see
Figure B-1
).
Step 3
Place the top packing material over the top of the Cisco 10008 chassis (see
Figure B-1
).
Step 4
Place both accessory boxes inside the cutouts in the top section of the packing material (see
Figure B-1
).
1
Front cover (bezel)
4
Bottom pallet
2
Accessory box
5
Top packing material
3
Filler box (empty)
6
Cisco 10000 router
132824
FANS
OK
FAN
FAILURE
MULTI-
FAN
FAILURE
When hot s
wapping this f
an tray,
removal and replacement m
ust
be done in under tw
o minutes or
system shutdo
wn will occur
.
CAUTION
LINK
F
AIL
C10000
1GE
TX
RX
PORT0
PORT1
PORT2
PORT3
PORT4
PORT5
F
AIL
CA ALARM
LOOP
C10000
6CT3
PORT0
PORT1
PORT2
PORT3
PORT4
PORT5
F
AIL
CA ALARM
LOOP
C10000
6CT3
PORT0
PORT1
PORT2
PORT3
PORT4
PORT5
F
AIL
CA ALARM
LOOP
C10000
6CT3
ACT
LNK
SLOT 1
C10000
CRE
CON
AUX
ETH
SLOT 2
CRITICAL
MAJOR
MINOR
STATUS
FAIL
ALARMS
ACO
ACT
LNK
SLOT 1
C10000
CRE
CON
AUX
ETH
SLOT 2
CRITICAL
MAJOR
MINOR
STATUS
FAIL
ALARMS
ACO
PORT0
PORT1
PORT2
PORT3
PORT4
PORT5
F
AIL
CA ALARM
LOOP
C10000
6CT3
PORT0
PORT1
PORT2
PORT3
PORT4
PORT5
FAIL
CA ALARM
LOOP
C10000
6CT3
PORT0
PORT1
PORT2
PORT3
PORT4
PORT5
F
AIL
CA ALARM
LOOP
C10000
6CT3
LINK
F
AIL
C10000
1GE
TX
RX
1
2
3
4
5
6 B-3
Cisco 10008 Router Hardware Installation Guide
OL-0659-13
Appendix B Repacking the Box
Figure B-2
Cisco 10008 System Package
Step 5
Fold the outside carton down over the top of the accessory boxes and seal with packing tape
(
Figure B-2
).
Step 6
Wrap two packaging straps tightly around the top and bottom of the package to hold the outside carton
and the bottom pallet (
Figure B-2
).
Caution
Do not use tape to hold the outside carton to the bottom pallet. Packaging straps must be used.
1
Carton
3
Packing straps
2
Pallet
132823
1
2
3 B-4
Cisco 10008 Router Hardware Installation Guide
OL-0659-13
Appendix B Repacking the Box