/td>Yahoo! is not affiliated with the authors of this page or responsible for its content.
Preface (added April 2003)
1
URL:
http://www.oism.org/nwss/
(accessed Mar. 4, 2003).
Preface (added April 2003)
Note
: The KFM, A Homemade Yet Accurate and Dependable Fallout Meter, was published by
Oak Ridge National Laboratory report in1979. Some of the materials originally suggested for
suspending the leaves of the Kearny Fallout Meter (KFM) are no longer available. Because of
changes in the manufacturing process, other materials (e.g., sewing thread, unwaxed dental floss)
may not have the insulating capability to work properly. Oak Ridge National Laboratory has not
tested
any of the following suggestions, but they have been used by other groups. When using
these instructions, the builder can verify the insulating ability of his materials by checking the
leakage rate and comparing it to the authors leakage tests. The principal author, Cresson Kearny, updated his instructions after his retirement from
ORNL in Appendix C of an 1987 edition of Nuclear War Survival Skills
1
to include two
suggestions for thin monofilament fishing line and narrow strips of dry cleaning bags:
Very thin monofilament fishing line or leader is an excellent insulator. The
2-pound- test strength, such as DuPont's Stren monofilament fishing line, is
best. Trilene 2-pound "nylon leader" a monofilament manufactured by Berkley
and Company, also is excellent. (A 4-pound monofilament line will serve, but is
disadvantageously stiff.) Some modern monofilament lines or leaders such as
Trilene contain an additive that makes them pliant, but also makes them poorer
insulators for the first several hours after being taken out of their dispenser and
used to suspend the leaves of a KFM. However, in about 6 hours the silica gel or
anhydrite drying agent in a KFM removes this additive and the monofilament
becomes as good an insulator as an even strands of unwaxed dental floss [tested
dental floss no longer available].
To minimize the chance of using a piece of monofilament or other
thread that has been soiled and thus changed into a poor insulator, always
first remove and discard the outermost layer of thread on any spool that
has not been kept clean in a plastic bag or other packaging after being
initially unwrapped.
...most American homes have an excellent insulator, very thin
polyethylene filmespecially clean dry cleaners' bags. A narrow
insulating strip cut only 1/16 inch wide can be used to suspend each
KFM leaf, instead of an insulating thread. (Installed leaves suspended on
strips of thin plastic film must be handled with care.)
To cut 1/16-inch-wide strips from very thin polyethylene film, first cut
a piece about 6 x 10 inches. Tape only the two 6-inch-wide ends to a
piece of paper (such as a brown grocery bag), so that the film is held flat
and smooth on the paper. Make 10 marks. 1/16 inch apart, on each of the
two tapes that are holding the film. Place a light so that its reflection on
the film enables you to see the edge of the film that you are preparing to 2
New material only: Copyright (c) 1986 by Cresson H. Kearny. The copyrighted material may be
reproduced without obtaining permission from anyone, provided: (1) all copyrighted material is reproduced
full-scale (except for microfiche reproductions), and (2) the part of this copyright notice within quotation marks is
printed along with the copyrighted material.
3
Dr. Paul Lombardi, URL:
http://www.sdavjr.davis.k12.ut.us/~paul/radiatio.htm
(accessed Mar. 4, 2003.)
cut. Then use a very sharp, clean knife or clean razor blade, guided by
the edge of a firmly held ruler, to cut nine strips, of which you will select
the best two. When cutting, hold the knife almost horizontal, with the
plane of its blade perpendicular to the taped-down film. Throughout this
procedure avoid touching the center parts of the strips.
2 A Utah teacher, who uses the Kearny Fallout Meter, in teaching about radiation, has
found that strands of clean human hair (cleaned with shampoo or alcohol) can be used as
an alternative suspension system
3
.







































This report was prepared as an account of work sponsored by an agency of
States Government. Neither the United States Government nor any agency thereof, nor
any of their employees, contractors, subcontractors, or their employees, makes any
warranty, express or implied, nor assumes any legal liability or responsibility for any
third partys use or the results of such use of any information, apparatus, product or
process disclosed in this report, nor represents that its use by such third party would
not infringe privately owned rights.
3 Dist. Category UC-41
Contract No. W-7405-eng-26
ENERGY DIVISION
THE KFM A HOMEMADE YET ACCURATE AND


- -
DEPENDABLE FALLOUT METER
H. Kearny
Paul R. Barnes
Conrad V. Chester
Margaret W. Cortner
Research sponsored by the Division of Biomedical
and Environmental
Energy,
under contractwiththe
Corporation.
Date Published: January 1978
OAK RIDGE NATIONAL LABORATORY
Oak Ridge, Tennessee 37830
operated by
UNION CARBIDE CORPORATION
for the
DEPARTMENT OF ENERGY
iii
CONTENTS
LIST OF FIGURES . . . . . . . . . . . . . . . . . . . . . . . . .
OAK RIDGE NATIONAL LABORATORY DRAWINGS AND PHOTOGRAPHS
USED IN THE INSTRUCTIONS . . . . . . . . . . . . . . . . . . . .
ACKNOWLEDGMENTS . . . . . . . . . . . . . . . . . . . . . . . . .
ABSTRACT . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1.
THE NEED FOR TRUSTWORTHY FALLOUT METERS THAT UNTRAINED
AMERICANS CAN QUICKLY MAKE AND USE . . . . . . . . . . . . .
2.
OBJECTIVES OF THIS REPORT . . . . . . . . . . . . . . . . . .
3.
PRIOR HOMEMADE FALLOUT INSTRUMENTS . . . . . . . . . . . . .
4.
BACKGROUND AND BASIC CAPABILITIES OF THE KEARNY FALLOUT
M E T E R ( K F M ) . . . . . . . . . . . . . . . . . . . . . . . . .
5.
FIELD-TESTED BUILDING AND OPERATING INSTRUCTIONS . . . . . .
5.1 Steps in the Development of the KFM Instructions . . . .
5.2 Objectives of These Instructions . . . . . . . . . . . .
5.3 Uses of This Report as Regards Its
Instructions . .
HOW TO MAKE AND USE A HOMEMADE FALLOUT METER, THE KFM
INSTRUCTIONS FOR PERSONS CONCERNED WITH REPRODUCING THE
KFM INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . . . .
LAYOUT FOR
TABLOID . . . . . . . . . . . . . . . . . . .
LOGO FORTABLOID . . . . . . . . . . . . . . . . . . . . . . . .
I.
II.
III.
IV.
V.
VI.
VII.
VIII.
IX.
X.
XI.
INSTALL THE ALUMINUM-FOIL LEAVES . . . . . . . . . . . .
Page 14
THE NEED FOR ACCURATE AND DEPENDABLE FALLOUT METERS
.
SURVIVAL WORK PRIORITIES DURING A CRISIS . . . . . . .
HOW TO USE THESE INSTRUCTIONS TO BEST ADVANTAGE
. . .
WHAT A KFM IS AND HOW IT WORKS . . . . . . . . . . . .
MATERIALS NEEDED . . . . . . . . . . . . . . . . . . .
USEFUL BUT NOT ESSENTIAL MATERIALS . . . . . . . . . .
TOOLS NEEDED . . . . . . . . . . . . . . . . . . . . .
MAKE THE DRYING AGENT
. . . . . . . . . . . . . . . .
MAKE THE IONIZATION CHAMBER OF THE KFM . . . . . . . .
MAK
E


SE
PARA
TE
8-PLY LEAV
E
S
OF
STAN
D
AR
D
(
NOT HEA
VY
DUTY) ALUMINUMFOIL
. . . . . . . . . . . . . . . . .










Page
vii
ix
1
6
7
7
10
11
Page 1
Page 2
Page 2
Page 2
Page 3
Page 6
Page 7
Page 7
Page 7
Page 8
Page 10 iv
Page
XII.
MAKE THE PLASTIC COVER . . . . . . . . . . .
Page
XIII.
TWO WAYS TO CHARGE A KFM. . . . . . . . . .
Page 17
XIV.
MAKE AND USE A DRY-BUCKET

. . .

. .

. Page 19
xv.
HOW USE A KFM AFTER A NUCLEAR ATTACK . . . . .
Page 20
A,
Background Information

.

. . .
Page
Finding the Dose Rate .



.

. . .
-
-
Page 21
C.
Calculating the Dose Received .

.
Page
D.
Estimating the Dangers from Different Doses . .
Page 22
Using a KFM to Reduce the Doses Received Inside a
Shelter . . . . . . . . ...*
. . .


Page 23
FOUR EXTRA PATTERN PAGES (for the recipient of this report
to use in making
so as not to damage the camera-ready
instructions) . . .

. .

.

. . . . . . .
ACCURACY AND RANGE OF THE
. . .
7.
CONCLUSIONS AND RECOMMENDATIONS . . .
APPENDICES
A.
DESIGN PRINCIPLES AND PROCEDURES USED IN DEVELOPING
THEKFM.
. . . .
. . .
ADDITIONAL TECHNICAL
. . . . .
B.l KFM Ionization Chambers

. . . .
Range and Accuracy of Measurements

.

.

Aluminum-Foil Leaves . . . .

.

. .
B.4 Insulating Threads . . . . . . .

.

. . .
Drying Agent . . . . . . . . . . . . . .

. .
Three Expedient Charging Devices

. .

. .
B.7 Charging a KFM in a Dangerously High Gamma Field . . .
Other Means for Charging
and Similar
Electroscope-Capacitors . . . . . . . . . . . LIST OF FIGURES
Page
5.1 Winning Hands .

. . . . . . . . . . . . . . . . .
8
5.2 Trimming Skirt of KFM Cover . . . . . . . . . . . . . . .
8
Balanced Forces Operating on the Charged
Leaves of a KFM . .

. . . . . . . . . . . . . . . 13
6.2 Calibration Curves for Two
with 8-Ply Leaves . . . . . 14
6.3 Normalized Calibration Points for Two
Derived Graphically from Fig. 6.2 . . . . . . . . . . . . 15
APPENDIX