ly. The
material can easily be cut with scissors dipped in a solution of soap and water.
Because the tape is supplied in pre-determined amounts, it eliminates the concern
of over/under application and material waste.
JMReadyBond is designed for adhering roofing insulation boards various substrates
as well as adhering boards to themselves. The tape should be applied 12 on-center
to clean, dry and dust-free substrates. Detailed application instructions can be found
in the attached data sheet.
JMReadyBond is only to be used on 4 x 4 insulation boards and cannot be used
with Fesco
®
or DuraBoard
®
in cold applied systems. It should be applied in
temperatures of 35° F (2° C) and rising.
Use product code 3332491 or alias JMRBTP in warehouse 96 to order. The tape is
packaged six rolls per carton and 30 cartons per pallet. For pricing, contact your
Pricing Administrator. The data sheet is attached for more information.
We are thoroughly pleased to offer this product as yet another option for our
contractors. If you have questions, please feel free to contact me.
Megan Wynn
Product Manager
Roofing Insulations Commercial / Industrial Roofing Systems
Adhesive Tape
Refer to the Material Safety Data Sheet and Product Label
prior to using this product.
RS-5178 10-04 V2 (Replaces 6-04)
Description
Johns Manvilles JMReadyBond is a 100% solid polymer-
modified asphaltic adhesive designed for adhering roofing
insulation boards to each other and to a variety of sub-
strates, including concrete roof decks. JMReadyBond
is also suitable for sealing side laps of non-granulated
modified bitumen membranes in roofing applications
where open flames are prohibited.
Application
For best results JMReadyBond should be applied 12
(305 mm) o.c. to clean, dry, dust-free substrates 100
(30.5 m) lineal feet per roof square. It is necessary to
prime concrete decks before application of the tape.
JMReadyBond tape should be stored at temperatures in
excess of 50º F (10º C) before application for best results
and should be applied in temperatures of 35º F (2º C) and
rising. Once the release paper is removed from the tape,
insulation should be set in place within 15 minutes to
avoid contamination from dust or other airborne particles.
The tape can be easily cut using scissors that have
been dipped in a solution of soap and water. When
Factory Mutual Approvals are a consideration and when
used in a JM guarantee job, JMReadyBond is only for
use on 4 x 4 (1.22 m x 1.22 m) insulation boards.
Note:
When JMReadyBond is being applied in temperatures
of 85F (29C) and rising, it is recommended that the
release paper is removed within 15 minutets of the
tapes application to facilitate easy paper release.
Advantages
JMReadyBond offers immediate adhesion no cure
time or set-up time is necessary.
100% solids formulation contains no VOCs.
JMReadyBond is supplied in pre-formed amounts,
eliminating concerns of over/under application and
material waste.
Job site waste is reduced as there are no cans or
buckets to throw away.
Easy to apply and cut.
Odor significantly reduced.
Sizes
JMReadyBond is supplied in .060 (1.52 mm) x 2.5
(63.5 mm) ribbons on 125 (22.86 m) rolls.
Packaging
6 rolls per carton
30 cartons per pallet
Shelf Life
18 months
Caution
JMReadyBond is not to be used with Fesco
®
Board or
DuraBoard in cold applied systems.
12 o.c.
12 o.c.
6
JMReadyBond
Adhesive
Tape
Deck
2nd Layer
Polyisocyanurate
Insulation
1st Layer
Polyisocyanurate
Insulation
12 o.c.