www.bemt.net/files/B3KUSA_Manual.doc
center;" dir="LTR">Rev
01
牋牋牋牋牋牋牋牋牋牋牋牋牋牋牋牋牋
www.b3kusa.com
牋牋牋 牋牋牋牋牋牋牋牋牋牋牋牋牋牋牋牋牋
B3KUSA, LLC.
牋牋牋牋牋牋
9541 NW 42nd St. Sunrise, FL 33351. Ph/Fax: 954-747-3673 toll:
866-362-3637
牋牋牋牋牋牋牋牋牋牋牋牋牋牋牋牋牋牋牋
e-mail: support@bemt.net
牋牋牋牋牋牋牋牋牋牋
Contents
I</span><span class="Normal--Char" style=" font-size: 14pt;">ntroduction................................................................2
Conventions,
abbreviations and symbols.....................3
Installation..................................................................4
Operation....................................................................4
Maintenance................................................................6
Safety
precautions.......................................................6
Trouble
shooting.........................................................7
Technical
specifications..............................................7
Labeling
and symbols..................................................8
Transport,
storage and packing contents......................8
Warranty.....................................................................9
1.
Introduction
Thank you for purchasing
the B3K USA PEMF system, designed and manufactured according to the
highest technical standards.
We trust that you will benefit very much by using this system and
that you, together with many other satisfied people, will improve your
quality of life dramatically.
We recommend that you read this manual carefully before operating
the system, for your safety and in order to obtain the best possible
results with this Pulsating ElectroMagnetic Field (PEMF) system. We
wish you a good health!
Conventions, abbreviations and symbols
Bold牋Important information
Italic牋Indicates button or switch
Pictogram燩icture with specific operational meaning
Start牋Start
Stop牋Stop
Pause牋Halt temporarily
Program燩re-programmed settings
Display燙lock and/or program number indication
LED牋Light Emitting Diode = indication lamp
Time牋Running time
Stand-by燤achine in sleep mode ready for use
Tesla牋Unit of electromagnetic field strength
mTesla爉illiTesla (1 mTesla = 10 Gauss)
V牋Volt
A牋Ampere
VA牋Volt-Ampere
Hz牋Hertz
ac牋alternating current
cm牋centimeter
hPa牋hectoPascal
牋 Caution: consult accompanying documents
Type BF equipment
Installation
Unpack the machine and
applicators and place the machine on a table (night stand) next to the
bed and put an applicator straight on the bed.
The applicator can be covered with a sheet if so wished, without any
influence on the results.
The applicators have no specific direction except for the large mattress
where the cable goes inside where the persons head is.
Connect the plug at the end of the cable coming from the applicator
to the round output connector on the backside of the B3K USA.
Lock the connector by turning it to the right until it clicks.
Check before connecting the B3K USA to the mains
if voltage and frequency comply with the ratings on the back panel.
Connect the power supply cable to the back of the machine and the
other side to the mains outlet.
Operation
Turn the system on with
the switch on the back of the machine.
The Stand-by LED on the clock display comes on.
The system is now ready for operation.
In order to make the
operation as simple as possible, pictograms have been used for the buttons,
which control the functions of the machine:
Start 牋= >
Stop 牋= 爮
Pause = 營I
Program=燸
Choose the program number
with program according to the recommendations at the end of this
chapter.
The number increases by one for each time program is pressed or advances automatically
when program is pressed continuously.
Note: for safety reasons and to avoid mistakes in operation, the program
number can only be changed when no program is active.
Lay down on the applicator and press start.
The LEDs, placed in a circle between the displays, are now lit and
run to indicate the correct working of the machine.
Simultaneously the clock display starts counting down until it shows
00.00 upon which the energy is switched off.
After a delay the system goes back into Stand-by mode.
If for any reason the session should be paused in the middle press pause
once. The energy is now switched off and the session is halted in the
middle. When you are ready to resume the session press pause once again and the energy output
continues.
If the session needs
to be discontinued in the middle, press stop.
The energy is switched o