olor=black>Yahoo! is not affiliated with the authors of this page or responsible for its content.
Quick Installation Guide Part Number: 4041642000100
Quick Installation Guide
HiCORE - i6420VLG
Version 1.0
FORM FACTOR
Full-sieze
SBC
PICMG
CPU TYPE
FC-PGA478
CHIPSET
ICH5
Intel 865GME
LAN
1000 Mbps
Gigabit
MEMORY
DDR
2GB
S-ATA x 2
AUDIO
AC'97
IP-ALCS20(optional)
I/O
USB/Serial/
IrDA/LPT/IDE/
FDD
CPU
Pentium 4
3.2 GHz 2
HiCORE-i6420VLG Quick Installation
Copyright
©
2003
All Rights Reserved.
The information in this document is subject to change without prior notice in
order to improve the reliability, design and function. It does not represent a
commitment on the part of the manufacturer.
Under no circumstances will the manufacturer be liable for any direct, indirect,
special, incidental, or consequen-tial damages arising from the use or inability
to use the product or documentation, even if advised of the possibility of
such damages.
This document contains proprietary information protected by copyright. All
rights are reserved. No part of this manual may be reproduced by any
mechanical, electronic, or other means in any form without prior written
permission of the manufacturer.
About this Quick Installation Guide
This Quick Installation Guide provides general information and installation
instructions about the SBC. This User's Manual is intended for experienced
users and integrators with hardware knowledge of personal computers. If
you are not sure about any description in this User's Manual, please consult
your vendor before further handling. 3
HiCORE-i6420VLG Quick Installation
Warning
Single Board Computers and their components contain very delicate
Integrated Circuits (IC). To protect the Single Board Computer and its
components against damage from static electricity, you should
always follow the following precautions when handling it :
1. Disconnect your Single Board Computer from the power source when you
want to work on the inside
2. Hold the board by the edges and try not to touch the IC chips, leads or
circuitry
3. Use a grounded wrist strap when handling computer components.
4. Place components on a grounded antistatic pad or on the bag that came
with the Single Board Computer, whenever components are separated
from the system
Replacing the lithium battery
Incorrect replacement of the lithium battery may lead to a risk of explosion.
The lithium battery must be replaced with an identical battery or a battery
type recommended by teh manufacturer (CR2032).
Do not throw lithium batteries into the trashcan. It must be disposed of in
accordance with local requlations concerning special waste.
Technical Support
If you have any technical difficulites, please consult the user's manual first
at:
ftp://ftp.arbor.com.tw/pub/install
Please do not hesitate to call or e-mail our customer service when you still
can not find out the answer.
http://www.arbor.com.tw
E-mail:info@arbor.com.tw 4
HiCORE-i6420VLG Quick Installation
Warranty
This product is warranted to be in good working order for a period of one
year from the date of purchase. Should this product fail to be in good working
order at any time during this period, we will, at our option, replace or repair it
at no additional charge except as set forth in the following terms. This
warranty does not apply to products damaged by misuse, modifications,
accident or disaster.
Vendor assumes no liability for any damages, lost profits, lost savings or any
other incidental or consequential damage resulting from the use, misuse of, or
inability to use this product. Vendor will not be liable for any claim made by
any other related party.
Vendors disclaim all other warranties, either expressed or implied, including
but not limited to implied warranties of merchantibility and fitness for a
particular purpose, with respect to the hardware, the accompanying product's
manual(s) and written materials, and any accompanying hardware. This limited
warranty gives you specific legal rights.
Return authorization must be obtained from the vendor before returned
merchandise will be accepted. Authorization can be obtained by calling or
faxing the vendor and requesting a Return Merchandise Authorization (RMA)
number. Returned goods should always be accompanied by a clear problem
description. 5
HiCORE-i6420VLG Quick Installation
Ordering Codes
HiCORE-i6420VLG
Full-Size Socket 478 Pentium SBC CRT, Serial ATA and 10/100/1000 Mbps LAN
FCDB-2110
Audio Codec Module (for HiCORE-i6420VL uses only)
HiCORE-i6420VLG
PACKING LIST
1xFDD Cable
1xATA-66/100 HDD ribbon cable
1xPrinter & COM1 ribbon cable
1xK/B & M/S Y type cable
1xK/B-M/S extend to BP cable
1xATX power control cable
1xUSB 2.0 cable (for 2 USB ports)
1xS-ATA & Power cable (for 1 S-ATA port)
1 x CD-ROM (driver)
HiCORE-i6420VLG Quick Installation
Before up and running, please make sure the package contains all of above
accessories.
If any of the above items is damaged or missing, contact your vendor
immediately.
Note: For fully utilize the versatile expanding abilities of HiCORE-i6420, you
need additional one USB and one S-ATA cables. Please contact your vendor
for purchasing information. 6
HiCORE-i6420VLG Quick Installation
Model
CPU
Socket 478 processors, for Intel
®
Pentium
®
4/ Celeron processor Up to 3.2GHz
Chipset
Intel
®
865G + ICH5 AGPset
Front Side Bus
400 / 533 / 800 MHz
Memory
2 x 184pins DIMM for DDR SDRAM up to
2GB (max.) Support DDR 266 / 333 / 400
SDRAM
Display
Intel
®
865G chipset integrated graphic
function
Audio
AC97 audio interface, by option audio card
--- IP-ALCS20 Onboard 9-pins (pin-
header) interface
SATA Function
Two S-ATA ports, support data transfer
rates up to 150MB/s
Onboard I/O
On-Chip I/O integrated with K/B, Mouse,
FDD, Parallel and Serial controller
Onboard PCI / IDE
Intel
®
ICH5 South Bridge controller
PCI rev2.2 Compliant
ACPI Compliant Power Management
PCI Bus IDE Port with PIO /ATA-100 x 2
(Up to 4 Devices)
BIOS
Award Plug & Play BIOS
Bracket I/O Connectors
D-Sub Serial port (COM1)
Single RJ-45 connector
15-pins D-Sub VGA connector
PS/2 style Mouse or Keyboard connector
Gigabit Ethernet Intel 82547GI
USB 2.0 Ports
4 x USB 2.0 ports (pin-header)
Extended Function
Hardware monitoring function
IrDA by pin-header
0.93lb (420g) --- IP-4PGP23
Weight
Specification
System Board
Multiple I/O
HiCORE-6420VLG 7
HiCORE-i6420VLG Quick Installation
Board Layout
CN7
LPT
CN4
FLOPPY
C O M 2
CN10
CN11
COM1
L A N
CN14
CN17 V G A
CN18
CN19
KB/MS
KB/MS
CN16
AC97
JP2
SATA2
SATA1
CN12
ATX CTL.
B A T T 1
JP1
CN3 CN6
IDE1
IDE2
C N 1 3
CN15
USB0/1
USB2/3
CN9
CN8
SYSTEM FAN
CPU FAN
DIMM1
DIMM2
CN1
B Z 1
CN2
92003 8
HiCORE-i6420VLG Quick Installation
Jumper/Connector Quick Reference
Jumpers
Lable
Function
JP1
Clear CMOS
JP2
Watchdog Timer Setting
Selection 9
HiCORE-i6420VLG Quick Installation
Jumper/Connector Quick Reference
Connectors
Functions
CN1
System Panel Indicate Connector
CN2
ATX 12V Power Connector
CN3
Secondary IDE Connector
CN4
Floppy Disk Connector
CN5
IrDA Connector
CN6
Primary IDE Connector
CN7
Parallel Port Connector
CN8
CPU FAN Connector
CN9
System FAN Connector
CN10
COM2 RS-232 Serial Port Connector
CN11
COM1 RS-232 Serial Port Connector
CN12
ATX Control Power Connector
CN13
USB0/1 Port Connector
CN14
Gigabit LAN (82547GI) RJ-45 Connector
CN15
USB2/3 Port Connector
CN16
Extension Audio (Pin-Header) Connector
CN17
CRT VGA Port Connector
CN18
External Keyboard & Mouse Connector
CN19
PS/2 Keyboard & Mouse Connector
SATA1
S-ATA1 Connector
SATA2
S-ATA2 Connector 10
HiCORE-i6420VLG Quick Installation
CMOS Jumper Settings
CMOS Operation (JP1)
Type : JP1: onboard 3-pin header
If the EmCORE-i6420 refuses to boot due to inappropriate CMOS settings, here
is how to proceed to clear (reset) the CMOS to its default values.
CMOS Setup (JP1)
JP1
Status
Normal Operation
1-2
ON
Clear CMOS
2-3
ON
default setting
1-2 ON
1 2 3
JP1
Watchdog Timer
Watchdog Output (JP2)
Mode Setting
Watchdog Mode
JP2
Enabled for Active NMI(I/O Channel Check)
1-2
Enabled for System Reset
2-3
Disable Watchdog Timer
None
default setting 2-3
IO por t: Enable/Refresh I/O port : 2FH
Level : 255 (1 level = 1 sec.)
Enable WDT demo program (by Debug under DOS):
-0 2e, 87
-0 2e, 87
-0 2e, 07
-0 2F, 08
-0 2e, F6
-0 2F, 30 ; count down 30 sec
-0 2e, 30
-0 2f, 01 ; start to count down
Refresh WDT demo program:
-0 2f, 30 ; Re-start to count down 30 sec.
Disable WDT demo program:
-0 2f, 0 ; send o to I/O port "2F"
1 2 3
JP2 11
HiCORE-i6420VLG Quick Installation
Switches and Indicators
2
1
20
19
CN1
System Panel Indicate Connector: CN1
Pin #
Assignment
Pin # Assignment
PWR LED
SPEAKER
1
+5V
2
SPKR (Default)
3
NC
4
BUZZ (Default)
5
PWLED
6
NC
KEYLOCK
8
+5V
7
KBLOCK
RESET
9
Ground
10
RESET
ATX PWR ON
12
Ground
11
Ground
HD_LED
13
NC
14
HDDLED
15
PSON
16
+5V
17
5VSB
PWR ON
19
PME
18
PWRBT+
20
PWRBT+
ATX 12V Power Connector
ATX 12V Power Connector:CN2
Type : onboard 4-pin Wafer connector
Pin
Description
1
GND
2
GND
3
+12V
4
+12V
1
4
3
2
Note: The system can not boot without connecting this connector. 12
HiCORE-i6420VLG Quick Installation
Connector : CN3
Type : 40-pins 2.54mm Pitch Pin-Header with Housing
Pin #
Assignment
Pin # Assignment
1
Reset IDE
2
Ground
3
Host Data 7
4
Host Data 8
5
Hos