td colspan=2>
« back to results for ""
Below is a cache of http://www.elitescreens.com/pdf/usersguide_cinetension_2.pdf. It's a snapshot of the page taken as our search engine crawled the Web.
The web site itself may have changed. You can check the current page or check for previous versions at the Internet Archive. Yahoo! is not affiliated with the authors of this page or responsible for its content.
Tension2 Electric Screen CineTension2 Series Ver.1.5 Users Guide www.elitescreens.com
/ eliteinfo@elitescreens.com












Tension2 Electric Screen
CineTension2 Series
Ver.1.5
Users Guide www.elitescreens.com
/ eliteinfo@elitescreens.com



Accessory for Cine Tension2 IR R
F Wall box
Red 1 2V
Green 0V 12V trigger
Eye receiver Battery
Please always point to the eye
receiver when using the IR remote
Bubble level
www.elitescreens.com
/ eliteinfo@elitescreens.com



Important Safety and Warning Precautions

1. Be
sure
to
read
this
manual
before use and follow the procedures specified:

Do not handle the power plug when your hands are wet or your feet are in contact with water. Please retain this manual for future reference.

To avoid any damage, do not use any accessories not recommended by the manufacturer.
Handle the device carefully during transportation to avoid impact.
Do not put the device on uneven or inclined surfaces.

Do not put heavy objects on the power cord; affix the power cord properly to avoid
someone tripping over it.

Never over load the power cord to prevent electrical shock or fire.

Guard the device from any liquid or foreign object to avoid electrical shock or f ire due to
loose contact or short circuit.
2. If any accessories need to be replaced, be careful to avoid short circuit.

3. There are no user serviceable parts in the device. Nobody except authorized technicians can open
this device. To prevent the risk of electrical shock or fire, protect against moisture and rain.
Make sure that the power source this device is connected to has a continuous power flow.

T he rating label on the product indicates the rated voltage.
4. Do not use this device under the following circumstances:

1) Disconnect the power cord under the condition of heavy wind, rain, thunder or lightning.
2) Avoid direct sunshine, rain shower or moisture.

3) Keep away from fire sources and high temperature to prevent this device from overheating.

4) Cut off the power supply first before transportation or maintenance.












































www.elitescreens.com
/ eliteinfo@elitescreens.com



Warning

NOTE:
The power outlet supplying power to the unit should be close to the unit and easily accessible
Reorient or relocate the receiving
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet using a circuit different from where the receiver is connected
Consult the dealer or an experienced radio/TV technician for help.
Individual modifications to this product are prohibited and will void the users warranty. Please
contact the Service Department for any questions.
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates uses and can radiate radio frequency energy and,
if not installed and used in accordance with the instructions, may cause harmful interference to radio
communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment
does cause harmful interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one or more of the
following measures:
To ensure safe and reliable operation, direct connection to a properly grounded power source is advised.




































www.elitescreens.com
/ eliteinfo@elitescreens.com


1. 12V Trigger:
12V trigger for your new Elite
Cinetension-----allows your screen to synchronize its drop and
rise with the projector's power cycle. The screen drops when the
projector powers up and retracts when the projector powers
down.
To Projector
Connection pins inside of case
Red DC12V
Green 0V

Video Projection Interface
2. IR (Infrared) Wall Box Kit and Eye Receiver:
The Wall Box Kit contains an IR receiver and
enables the consumer to use either the IR remote or hardwire controls to operate the screen's drop/rise capabilities. IR eye
protrudes from the bottom of the casing to present a low profile line-of-sight control option for your IR remote. It is a low-
visibility alternative to using the wall box kit and its ability to protrude from the bottom of the screen allows line-of-sight
control even in a recessed ceiling install at ion.
Connection pins
inside of case
Connection pins
inside of case
Sensor
Wall-mounted Receiver
(Extension Sensor)
Transmitter
Sensor
3. Bubble Level:
Included with the installation package is a small bubble level that can be useful in
determining if the screen is perfectly level when installing.
NOTE
: Please use the Down sign side as the bottom.
Bubble

The Bubble should be in the middle position to determine that it is level.
www.elitescreens.com
/ eliteinfo@elitescreens.com



Please read this guide prior to installation.

Make sure the current rating is equal to that of the appliance rating when an extension cord is used.
Do not use any accessories not provided by the manufacturer with this screen. We will not be
responsible for any risks of fire, electric shock, or injuries resulting from the misuse of this product
with accessories not designed for use with this product.
Make sure the screen is mounted in a horizontal level position. We suggest consulting with a professional if
y<b>ou are unsure on how to perform a proper installation.
INSTALLATION
*Allow 2 of spacing between the front and back of the screen casing.
I. Masonry Anchors are used on concrete/masonry wall/ceilings; Plastic drywall anchors are included for drywall
mounting.
II. Wood screws are to be used for wooden wall/ceiling studs on screen sizes less than or equal to 120 inches (diagonal).
Masonry anchors should be used for wall/ceiling installations of screen sizes greater than 120inches (diagonal).
III. Install the Aluminum Extruded Hanger set onto the slide channel and move to the desired position before locking it
by tightening the connecting bolt.
MO UNT ING ACCE S SOR IES
Upon assembly the bracket will slide into the
casing rails for mounting.

A
A
B
C
D


Warning: Standard screws x 2 for each type
B

C
D
These are standard accessories included with the ceiling/wall brackets. Models may
vary and anchors will not support all models.
www.elitescreens.com
/ eliteinfo@elitescreens.com



The IR receiver will be connected from the screen
11.65 mm. in width
The 3 prong cable will be
connected from the outlet
to the case.
Although the IR remote requires a direct line of sight with the IR sensor
to function, the case can be hidden from sight and operated using the RF
remote. When depressing the directional buttons you should hear a faint
click signifying that the mechanism is working properly.
80mm in width
IR
UP

Stop

Down
RF
This is the IR (Infra-Red) remote with a
range of 15 Ft. Battery size AAA
This is the RF (Radio Frequency) remote
with a range of 30 Ft. Battery size AAA
** Please remember to always point to the wall switch receiver when using the IR remote. The IR remote can also work
with a Universal Learning Remote Control usually by programming the Screens IR codes into your Universal Learning
Remote.
www.elitescreens.com
/ eliteinfo@elitescreens.com



FO R REFEREN CE ONLY:
(Attention: This adjustment is not required. The screens tension has been set to achieve its
best performance. Always contact an Elite Screen Technician for assistance to avoid
damaging the screen and voiding your warranty.)
Pulling the knob and turning it Clockwise it will create more tension to the screen. By
pulling the knob Counter-clockwise it will start to release tension
If the electric screen does not move, please check the following:
1. Check
the
power supply first. The screen will understandably not move without power.
2. Make sure the power cord is firmly plugged to the power outlet.
3. Make sure that all cable connections are se