kit to be free from defects in both material and workmanship at the date of purchase.
This warranty does not cover any component parts damaged by use or modification. In no case shall Tower Hobbies
liability exceed the original cost of the purchased kit. Further, Tower Hobbies reserves the right to change or modify
this warranty without notice.
In that Tower Hobbies has no control over the final assembly or material used for final assembly, no liability shall be
assumed nor accepted for any damage resulting from the use by the user of the final user-assembled product. By the act
of using the user-assembled product, the user accepts all resulting liability.
If the buyer is not prepared to accept the liability associated with the use of this product, the buyer is advised to
return this kit immediately in new and unused condition to the place of purchase.
READ THROUGH THIS MANUAL COMPLETELY BEFORE STARTING CONSTRUCTION. IT CONTAINS
IMPORTANT INSTRUCTIONS AND WARNINGS CONCERNING THE ASSEMBLY AND USE OF THIS MODEL.
© Copyright 2002 V 1.0
TOWZ1153 for TOWA1010
Tower Hobbies
P.O. Box 9078
Champaign, IL 61826
(800) 637-6050
www.towerhobbies.com
TOWER TRAINER 60 MKII
ALMOST-READY-TO-FLY RADIO CONTROLLED MODEL AIRPLANE
ASSEMBLY INSTRUCTIONS
ARF
Wingspan: 69 in [1,753mm]
Wing Area: 880 sq in [57 dm
2
]
Weight: 7.25 lbs [3,289 g] Length: 56.5 in [1,435mm]
Wing Loading: 19 oz/sq ft [58 g/dm
2
]
Engine: .61 cu in [10 cc] two-stroke
Radio: 4 channel
®
® TABLE OF CONTENTS
INTRODUCTION ..............................................................2
SAFETY PRECAUTIONS ................................................2
ADDITIONAL ITEMS REQUIRED ...................................3
ENGINE RECOMMENDATIONS ................................3
RADIO RECOMMENDATIONS ..................................3
COVERING ACCESSORIES......................................3
ADHESIVES & ASSEMBLING SUPPLIES .....................3
OPTIONAL SUPPLIES & TOOLS ...................................3
PREPARATIONS..............................................................3
ASSEMBLE THE WING ...................................................4
JOIN THE WING ........................................................4
HOOK UP THE AILERONS........................................6
ASSEMBLE THE FUSELAGE .......................................10
MOUNT THE STAB & FIN........................................10
INSTALL THE WING MOUNTING DOWELS .................13
INSTALL THE FUEL TANK ............................................14
MOUNT THE ENGINE....................................................15
MOUNT THE LANDING GEAR......................................17
FINAL ASSEMBLY ........................................................19
HOOK UP THE CONTROLS....................................19
INSTALL THE RADIO GEAR ...................................21
APPLY THE DECALS ....................................................23
GET THE MODEL READY TO FLY................................23
CHECK THE CONTROL DIRECTIONS ...................23
SET THE CONTROL THROWS ...............................24
BALANCE THE MODEL (C.G.) ................................25
BALANCE THE MODEL LATERALLY ......................25
PREFLIGHT ...................................................................25
IDENTIFY YOUR MODEL ........................................25
CHARGE THE BATTERIES .....................................25
BALANCE THE PROPELLERS................................26
GROUND CHECK ....................................................26
RANGE CHECK .......................................................26
ENGINE SAFETY PRECAUTIONS ...............................26
AMA SAFETY CODE (EXCERPTS)..............................27
CHECK LIST ..................................................................27
GETTING READY TO FLY .............................................27
USING RUBBER BANDS.........................................28
TAXIING....................................................................28
TAKEOFF .................................................................28
FLYING .....................................................................28
LANDING..................................................................29
FUEL MIXTURE ADJUSTMENTS .................................29
MODELING TERMS & TRIVIA.......................................29
PARTS LIST.................................................center section
INTRODUCTION
Thank you for purchasing our Tower Trainer 60 MKII
ARF. This model has been specially created for you and
other first-time radio control modelers. The Tower Trainer 60
MKII ARF offers nearly all the excitement of piloting a real
airplaneand develops skills that will take you anywhere
you want in your new hobby.
PROTECT YOUR MODEL, YOURSELF &
OTHERS...FOLLOW THESE IMPORTANT
SAFETY PRECAUTIONS
1. Your Tower Trainer 60 MKII ARF should not be
considered a toy, but rather a sophisticated, working model
that functions very much like a full-size airplane. Because of
its performance capabilities, the Tower Trainer 60 MKII ARF,
if not assembled and operated correctly, could possibly
cause injury to yourself or spectators and damage property.
2. You must assemble the model according to the
instructions. Do not alter or modify the model, as doing so
may result in an unsafe or unflyable model.
3. You must take time to assemble straight, true and strong.
4. You must use an R/C radio system that is in first-class
condition, and a correctly sized engine and components
(fuel tank, wheels, etc.) throughout the assembly process.
5. You must properly install all R/C and other components
so that the model operates properly on the ground and in
the air.
6. You must check the operation of the model before every
flight to insure that all equipment is operating and that the
model has remained structurally sound. Be sure to check
clevises or other connectors often and replace them if they
show any signs of wear or fatigue.
7. If you are not already an experienced R/C pilot, you
should fly the model only with the help of a competent,
experienced R/C pilot.
Remember: Take your time and follow the instructions to
end up with a well-built model that is straight and true.
If you have not flown this type of model before, we
recommend that you get the assistance of an experienced
pilot in your R/C club for your first flights. If youre not a
member of a club, your local hobby shop has information
about clubs in your area whose membership includes
experienced pilots.
In addition to joining an R/C club, we strongly recommend
you join the AMA (Academy of Model Aeronautics). AMA
membership is required to fly at AMA sanctioned clubs.
There are over 2,500 AMA chartered clubs across the
country. Among other benefits, the AMA provides insurance
We, as the kit manufacturer, provide you with a top
quality kit and instructions, but ultimately the quality and
flyability of your finished model depends on how you
assemble it; therefore, we cannot in any way guarantee
the performance of your completed model, and no
representations are expressed or implied as to the
performance or safety of your completed model.
2 to its members who fly at sanctioned sites and events.
Additionally, training programs and instructors are available
at AMA club sites to help you get started the right way. Contact
the AMA at the address or toll-free phone number below:
Academy of Model Aeronautics
5151 East Memorial Drive
Muncie, IN 47302-9252
Tele. (800) 435-9262
Fax (765) 741-0057
Or via the Internet at:
http://www.modelaircraft.org
ADDITIONAL ITEMS REQUIRED
This is the list of hardware and accessories required to
finish the Tower Trainer 60 MKII ARF. Order numbers are
provided in parentheses.
Engine Recommendations
TOWER HOBBIES 61 ABC (TOWG0161)
O.S.
®
65 LA (OSMG0065)
O.S. 61 FX (OSMG0561)
SUPERTIGRE
®
G-61 Ring (SUPG0161)
SUPERTIGRE G-61 ABC (SUPG0181)
Radio Recommendations
FUTABA
®
4VF (FUTJ62**)
Covering Accessories
Tower Custom Sealing Iron (TOWR3250)
Top Flite
®
Hot Sock Iron Cover (TOPR2175)
ADHESIVES & ASSEMBLING SUPPLIES
In addition to common household tools and hobby tools,
this is the short list of the most important items required to
assemble the Tower Trainer 60 MKII ARF.
Tower Hobbies
Build-it CA and Epoxy glue are recommended. 2 oz. Tower Hobbies Build-it CA (TOWR3800) 30-Minute Tower Hobbies Build-it Epoxy (TOWR3811) 6-Minute Tower Hobbies Build-it Epoxy (TOWR3807) Hobby Knife (HCAR0105), #11 Blades (HCAR0211) Small T-pins (HCAR5100) Builders triangle (HCAR0480) Small Phillips and flat blade screwdrivers Small metal file Pliers with wire cutter (HCAR0630) Threadlocker (GPMR6060) RTV Silicone Great Planes
®
Easy-Touch Bar Sander (GPMR6170) Easy-Touch Sandpaper, 180 Grit (GPMR6184)
OPTIONAL SUPPLIES & TOOLS
Here is a list of optional tools mentioned in the manual that
will help you assemble the Tower Trainer 60 MKII ARF. Great Planes CG Machine (GPMR2400) Top Flite Precision Magnetic Prop Balancer (TOPQ5700) Masking Tape (TOPR8018) Epoxy Brushes (GPMR8060) Mixing Sticks (GPMR8055) Denatured Alcohol (for epoxy clean up) Non-elastic monofilament or Kevlar fishing line (K&SR4575) Builders Triangle Set (HCAR0480) Masking Tape (TOPR8018) Felt-Tip Marker (TOPQ2510) Hobbico Servo Horn Drill (HCAR0698) Great Planes AccuThrow Deflection Gauge (GPMR2405)
PREPARATIONS 1. Remove the major parts of the kit from the box (wings,
fuselage, tail parts, etc.) and inspect them for damage. If any
parts are damaged or missing, contact Product Support at the
address or telephone number listed in this manual. 2. Remo