=100%>Yahoo! is not affiliated with the authors of this page or responsible for its content.
Certificate of Compliance
The 'C' and 'US' indicators adjacent to the CSA Mark signify that the product has been evaluated to the applicable CSA and ANSI/UL Standards, for use in Canada and
the U.S., respectively. This 'US' indicator includes products eligible to bear the 'NRTL' indicator. NRTL, i.e. National Recognized Testing Laboratory, is a designation
granted by the U.S. Occupational Safety and Health Administration (OSHA) to laboratories which have been recognized to perform certification to U.S. Standards.
F F 0 2

DQD 507WD 2003/01/31

Page 1

Certificate of Compliance

Certificate:
1437894
Master Contract: 169502 (LR 60142)

Edition:
1
Date Issued: May 21, 2003

Issued to:
Beckman Coulter Inc.
P.O. Box 3100, 4300 N. Harbor Blvd.
Fullerton, CA 92834-3100
USA
The products listed below are eligible to bear the CSA Mark shown
with adjacent indicators 'C' and 'US'




Issued by:
John Chiang, P. Eng.



Approved by: Terry Nagy


Operations Manager

PRODUCTS

CLASS 8721 04 - LABORATORY ELECTRICAL EQUIPMENT
CLASS 8721 84 - ELECTRICAL EQUIPMENT FOR LABORATORY USE (Certified to U.S. Standards)

Paragon Power Supply, Model 6558, Catalog No. 655803, rated 120 V, 1.0 A, 50/60 Hz, and Catalog No. 655804,
rated 240 V, 0.5 A, 50/60 Hz.


Note: The above model is Equipment Class I, Pollution Degree 2, Installation Category II.

Certificate: 1437894
Edition:
1
Master Contract: 169502 (LR 60142)
Date: May 21, 2003

DQD 507WD 2003/01/31
Page 2


APPLICABLE REQUIREMENTS


CAN/CSA-C22.2 No. 1010.1-92 - Safety Requirements for Electrical Equipment for Measurement,
Control, and Laboratory Use, Part 1: General Requirements
(Includes Amendment 1)


CAN/CSA-C22.2 No. 1010.1B-97 - Amendment 2 to CAN/CSA-C22.2 No. 1010.1-92, "Safety
Requirements for Electrical Equipment for Measurement,
Control, and Laboratory Use, Part 1: General Requirements"


UL Std No. 61010A-1 - Electrical Equipment for Laboratory Use; Part 1: General
Requirements


IEC 61010-1 - Safety Requirements for Electrical Equipment for Measurement,


Control, and Laboratory Use, Part 1: General Requirements


(Including Amendment 1:1992 and Amendment 2:1995)


CONDITIONS OF ACCEPTABILITY

The equipment is supplied with an approved power supply cord set or power supply cord with plug that is
acceptable to the authorities in the country where the equipment is to be used.




DQD 507WD 2003/01/31
Page 1


Supplement to Certificate of Compliance
Certificate:
1437894
Master Contract: 169502 (LR 60142)
The products listed, including the latest revision described below,
are eligible to be marked in accordance with the referenced Certificate.
Product Certification History
Edition
Date
Description
1
May 21, 2003
Original Certification.




Descriptive and
Test Report

The test report shall not be reproduced, except in full, without the approval of CSA International.


S:\DUMP\HOLD\Jocelyn\Beckman\60142 - Porterville\1437894 - Paragon Power Supply\1437894.rep.doc\jj
MASTER CONTRACT: 169502 (LR 60142)
REPORT: 1437894

Edition 1:
May 21, 2003; Project 1437894 -Vancouver
Issued by John Chiang, P. Eng.
Contents:
Certificate of Compliance - Pages 1 to 2
Supplement to Certificate of Compliance - Page 1
Description and Tests - Pages 1 to 22
Figures - Figs. 1 to 6


PRODUCTS

CLASS 8721 04 - LABORATORY ELECTRICAL EQUIPMENT
CLASS 8721 84 - ELECTRICAL EQUIPMENT FOR LABORATORY USE (Certified to U.S. Standards)

Paragon Power Supply, Model 6558, Catalog No. 655803, rated 120 V, 1.0 A, 50/60 Hz, and Catalog No. 655804,
rated 240 V, 0.5 A, 50/60 Hz.


Note: The above model is Equipment Class I, Pollution Degree 2, Installation Category II.


CSA C22.2 No. 1010.1 (Ver 2.0) CERTIFICATION REPORT SUPPLEMENT (DESIGN MANUAL ISSUED
UNDER REPORT 169502-1240902) IS AN INTEGRAL PART OF THIS REPORT

MASTER CONTRACT: 169502 (LR 60142)
REPORT: 1437894
EDITION: 1

Page No: 2
Date Issued: May 21, 2003

S:\DUMP\HOLD\Jocelyn\Beckman\60142 - Porterville\1437894 - Paragon Power Supply\1437894.rep.doc\jj

APPLICABLE REQUIREMENTS


CAN/CSA-C22.2 No. 1010.1-92 - Safety Requirements for Electrical Equipment for Measurement,
Control, and Laboratory Use, Part 1: General Requirements
(Includes Amendment 1)


CAN/CSA-C22.2 No. 1010.1B-97 - Amendment 2 to CAN/CSA-C22.2 No. 1010.1-92, "Safety
Requirements for Electrical Equipment for Measurement,
Control, and Laboratory Use, Part 1: General Requirements"


UL Std No. 61010A-1 - Electrical Equipment for Laboratory Use; Part 1: General
Requirements


IEC 61010-1 - Safety Requirements for Electrical Equipment for Measurement,


Control, and Laboratory Use, Part 1: General Requirements


(Including Amendment 1:1992 and Amendment 2:1995)


CONDITIONS OF ACCEPTABILITY

The equipment is supplied with an approved power supply cord set or power supply cord with plug that is
acceptable to the authorities in the country where the equipment is to be used.


MARKINGS

The following markings appear on the product and may be described in further detail in the Certification Report
Supplement, Section C:

1.
Submittor's identification (company name and/or file number and/or registered tradename);
2.
Factory identifier; [if required]
3.
Model designation;
4.
Electrical rating;
5.
Date of manufacture (or traceable serial number);
6.
The CSA Monogram with C/US subscript;
7.
Replacement fuse markings;
8.
The IEC 417, No. 5019a earthing symbol;
9.
On and/or Off positions of the power switch.

Marking Method: The above markings are made via silk screening, die stamping, molding, or by adhesive
materials compatible with the surface used, or other equivalent permanent means (see "Construction Details:
Labels").
MASTER CONTRACT: 169502 (LR 60142)
REPORT: 1437894
EDITION: 1

Page No: 3
Date Issued: May 21, 2003

S:\DUMP\HOLD\Jocelyn\Beckman\60142 - Porterville\1437894 - Paragon Power Supply\1437894.rep.doc\jj

DOCUMENTATION: As outlined in the Certification Report Supplement, Section D.

Documentation Includes the Following:

1.
Pollution degree 2;
2.
Installation category II;
3.
Altitude 2000 m;
4.
Humidity 15 to 85%;
5.
Electrical supply 120 V, 1.0 A, 50/60 Hz, or 240 V, 0.5 A, 50/60 Hz;
6.
Indoor use statement;
7.
Temperature 15°C to 40°C.


ALTERATIONS

1.
All markings specified above shall be on the equipment.
2.
Marking methods specified above shall be used.


FACTORY TESTS

Warning: The factory test(s) specified may present a hazard of injury to personnel and/or property and should
only be performed by persons knowledgeable of such hazards and under conditions designed to minimize the
possibility of injury.

1.
At the conclusion of manufacture and before shipment, the equipment shall withstand a potential of
1350 V ac or 1900 V dc applied for 2 seconds without breakdown, when applied between live parts and
exposed non-current carrying metal parts.

2.
In addition, the equipment shall be tested to verify the bonding of accessible conductive parts to the main
earthing terminal, using any means to indic ate a conductive path (i.e. ohmmeter, battery/light fixture, etc.)

The factory test may be made at existing room temperature.


ENGINEERING CONSIDERATIONS:

1.
The Power Supply is a tabletop, cord-connected accessory designed to be used for electrophoretic
separations that require a DC potential of 50, 100, 150, or 200 volts. The unit is a two-channel power
supply and comes with two Gel Cell holders that plug into front connectors.

2.
All electrical components are housed within a combination metallic and thermoplastic enclosure and are
provided with a Listed cord set.

3.
This device is intended for use in an Installation Category II, Pollution Degree 2 environment.

MASTER CONTRACT: 169502 (LR 60142)
REPORT: 1437894
EDITION: 1

Page No: 4
Date Issued: May 21, 2003

S:\DUMP\HOLD\Jocelyn\Beckman\60142 - Porterville\1437894 - Paragon Power Supply\1437894.rep.doc\jj

CONSTRUCTION DETAILS:

Representative sample(s) of the equipment(s) covered was examined and tested at the Manufacturer/Listee
location under the CSA Category Certification Program. Unless otherwise specified, the following general
definitions, terminology, and construction details apply:

Asterisk: In "Certified*" the asterisk denotes that the CSA Monogram appears on the component.

Bonding: All accessible dead metal parts liable to become energized are acceptably connected together, and to
the grounding means, by straps and/or wires, bolts, screws, and star washers (to ensure surface coating
penetration), in conformance with Clause 3.4 of CSA Standard C22.2 No. 0.4-M1982.

Connectors: Connectors, including crimp types, used in primary, grounding and non-ELV secondary circuits are
Certified, appropriately sized for the gauge of wir