C
EPT sealer
Fuse label
2 Tapping screws
Flange nut
Cable clip
Accessory users information manual
Back-up Sensor Kit
P/N 08V67-SWA-101K
Right center sensor (blue)
Left center sensor (blue)
2 Corner sensors (white)
TOOLS AND SUPPLIES REQUIRED
Phillips screwdriver
Flat-tip screwdriver
Ratchet
8 mm and 10 mm Socket
Pushpin
Felt-tip pen
Drill
3 mm, 5 mm Drill bit
16 mm, 24 mm, and 26 mm Hole saw
Ruler
Eye protection (safety goggles, face shield, etc.)
10 mm Combination wrench
File
Diagonal cutters
Utility knife
LOCATING
PIN
LOCATING
PIN
LOCATING PIN © 2006 American Honda Motor Co., Inc. All Rights Reserved
AII 32953 (0609)
3 of 13
Illustration of the Back-Up Sensors Installed on
the Vehicle
INSTALLATION
NOTE: If you are also installing a trailer hitch, install the
back-up sensor first.
1.
Make sure you have the anti-theft code for the radio
and navigation system, then write down the radio
presets.
2.
Disconnect the negative cable from the battery.
Customer Information: The information in this
installation instruction is intended for use only by skilled
technicians who have the proper tools, equipment, and
training to correctly and safely add equipment to your
vehicle. These procedures should not be attempted by
do-it-yourselfers.
6311121B
BACK-UP
SENSOR
SUBHARNESS
RIGHT
CORNER
SENSOR
LEFT
CORNER
SENSOR
CENTER
SENSOR
CONTROL
UNIT
BACK-UP
SENSOR
HARNESS
BUZZER
FUSE
(2A)
3.
If equipped, remove the tonneau cover.
4.
Remove the right rear door sill trim (three clips).
TONNEAU
COVER
Pull.
RIGHT REAR
DOOR SILL TRIM
CLIPS (3)
FRONT 4 of 13
AII 32953 (0609)
© 2006 American Honda Motor Co., Inc. All Rights Reserved
5.
Remove the trunk board (two hooks).
6.
Remove the weatherstrip from around the rear trim
panel. Remove the rear trim panel (two bolts with tie-
down hooks, two clips, and four clips).
HOOK
TRUNK BOARD
6627010B
CLIPS (4)
REAR TRIM
PANEL
CLIPS (2)
TIE-DOWN
HOOKS
BOLTS (2)
WEATHER-
STRIP
7.
Fold the rear seats forward, and remove the right
rear lid from the right cargo area side trim (ten retain-
ing tabs).
8.
Remove the vehicle bolt from the bracket of the right
cargo area side trim panel.
9.
Remove the rear door and tailgate weatherstrip from
the right cargo area side and two clips from the trim
panel.
10. Remove the right cargo area side trim panel (ten
clips).
6811060B
RIGHT CARGO AREA
SIDE TRIM PANEL
RETAINING
TABS (10)
RIGHT REAR LID
VEHICLE
BOLT
FRONT
RIGHT REAR TRIM
PANEL BRACKET
690
CLIPS (8)
RIGHT CARGO AREA
SIDE TRIM PANEL
CLIP
FRONT
WEATHERSTRIP
WEATHER-
STRIP © 2006 American Honda Motor Co., Inc. All Rights Reserved
AII 32953 (0609)
5 of 13
11. Remove the seat belt from the right quarter pillar trim
(one cover and one vehicle bolt).
12. Remove the right quarter pillar glass trim (seven
clips).
6222050B
FRONT
COVER
SEAT BELT
SEAT BOLT
RIGHT QUARTER
PILLAR TRIM
6222060B
FRONT
CLIPS (7)
RIGHT QUARTER
PILLAR GLASS
TRIM
13. Remove the left rear splash guards four self tapping
screws.
14. Remove the right rear splash guard (four self-tap-
ping screws).
15. With the help of an assistant, remove th rear bumper
(two bolt covers, two bolts, two flange bolts, and
three clips).
6620011Y
SELF-TAPPING
SCREWS (4)
SPLASH GUARD
6222
COVER
CLIP
REAR
BUMPER
FLANGE
BOLTS
REAR
BUMPER
BUMPER
SCREWS (2)
FLANGE
BOLT 6 of 13
AII 32953 (0609)
© 2006 American Honda Motor Co., Inc. All Rights Reserved
16. Get the back-up sensor harness, and attach the 2A
fuse label (2A) to the fuse case.
17. Install the cargo area, remove the clip that secures
the vehicle 6-pin connector to the vehicle panel and
disconnect the vehicle 6-pin connector.
18. Plug the back-up sensor 6-pin connector into the
vehicle 6-pin connector. Plug the other vehicle 6-pin
connector into the other back-up sensor harness 6-
pin connector.
6216
FUSE LABEL
(2A)
BACK-UP SENSOR
HARNESS
FUSE
CASE
6311011B
BACK-UP SENSOR
HARNESS
FRONT
CLIP
VEHICLE
6-PIN CONNECTOR
VEHICLE PANEL
VEHICLE 6-PIN
CONNECTOR
6-PIN
CONNECTOR
6-PIN
CONNECTOR
19. Reinstall the vehicle 6-pin connector clip to the vehi-
cle panel.
20. Secure the other 6-pin connector to the vehicle
harness with one wire tie.
21. Using isopropyl alcohol on a shop towel, thoroughly
clean the area where the cushion tape will attach.
Attach the cushion tape to the edge of the vehicle
panel at the location shown.
6311021B
FRONT
CLIP
BACK-UP SENSOR
HARNESS
VEHICLE
PANEL
VEHICLE 6-PIN
CONNECTOR
6311031B
BACK-UP SENSOR
HARNESS
FRONT
6-PIN
CONNECTOR
WIRE TIE
VEHICLE
HARNESS
CUSHION
TAPE
VEHICLE PANEL
EDGE © 2006 American Honda Motor Co., Inc. All Rights Reserved
AII 32953 (0609)
7 of 13
22. Slide the control unit bracket onto the control unit.
Make sure that the three switch knobs are in the
down position.
23. Plug the back-up sensor harness 14-pin connector
into the control unit.
24. Attach the back-up sensor harness clip to the control
unit bracket.
6905070B
CONTROL
UNIT
CONTROL UNIT
BRACKET
SWITCH KNOB
Down positions
6224060B
CONTROL UNIT
BRACKET
CONTROL
UNIT
BACK-UP SENSOR
HARNESS
BACK-UP SENSOR
HARNESS CLIP
BACK-UP SENSOR
HARNESS 14-PIN
CONNECTOR
25. Insert the stud from the control unit bracket into the
hole in the vehicle panel, make sure that the bracket
tab is seated in the large hole. Secure the bracket to
the vehicle panel using the 6 mm flange nut.
26. Install the back-up sensor harness clip into the hole
in the vehicle panel.
6311041B
CONTROL
UNIT
CONTROL UNIT
BRACKET
FRONT
HOLE
VEHICLE
PANEL
6 mm
FLANGE
NUT
STUD
LARGE
HOLE
BRACKET
TAB
6224080B
FRONT
BACK-UP SENSOR
HARNESS CLIP
BACK-UP SENSOR
HARNESS
VEHICLE
PANEL
HOLE 8 of 13
AII 32953 (0609)
© 2006 American Honda Motor Co., Inc. All Rights Reserved
27. Using a utility knife trim off the right quarter pillar
glass trim in the area shown.
28. Using a ruler and a felt-tip pen, measure and mark
the right quarter pillar glass trim in the area shown.
6525501
RIGHT QUARTER
PILLAR GLASS
TRIM
RIB
15 mm
10 mm
UTILITY
KNIFE
Cut off.
6525512B
RIGHT QUARTER
PILLAR GLASS
TRIM
MARK
FELT-TIP
PEN
RIB
RIB
18 mm
22 mm
6.5 mm
6.5 mm
18 mm
13 mm
29. While wearing eye protection, drill a 4 mm hole at
the two marked points, and remove any burrs.
30. While wearing eye protection, drill a 3 mm bit, drill a
hole at the marked point, then finish with a 16 mm
hole saw. Remove any burrs.
6525520B
RIGHT QUARTER
PILLAR GLASS TRIM
MARK
DRILL
(3 mm 5 mm
DRILL BIT)
6525530B
RIGHT QUARTER
PILLAR GLASS TRIM
DRILL
(3 mm DRILL BIT)
DRILL
(16 mm HOLE SAW)
MARK © 2006 American Honda Motor Co., Inc. All Rights Reserved
AII 32953 (0609)
9 of 13
31. Using isopropyl alcohol on a shop towel, clean the
right quarter pillar glass trim where the double-sided
tape will attach. Remove the adhesive backing from
the buzzer. Route the buzzer 2-pin connector
through the 16 mm hole, and install the buzzer in the
right quarter pillar glass trim with the two self tapping
screws. Install with the switch and the volume label
toward the front.
32. Reinstall the right quarter pillar glass trim.
33. Plug the back-up sensor harness 2-pin connector
into the buzzer 2-pin connector.
34. Secure the 2-pin connector to the vehicle harness
with one wire tie (without vehicle harness: wire tie
with clip B).
6822011B
RIGHT QUARTER
PILLAR GLASS TRIM
SELF-TAPPING
SCREWS (2)
BUZZER 2-PIN
CONNECTOR
5 mm
HOLE
DOUBLE-SIDED
TAPE
5 mm
HOLE
16 mm
HOLE
BUZZER
FRONT
SWITCH
VOLUME
LAVEL
ADHESIVE
BACKING
6905080B
BUZZER
FRONT
VEHICLE
PANEL
BUZZER 2-PIN
CONNECTOR
VEHICLE
HARNESS
WIRE TIE
2-PIN
CONNECTOR
With Vehicle Harness
BACK-UP SENSOR
HARNESS 2-PIN
CONNECTOR
35. Secure the buzzer harness to the vehicle harness
with one wire tie.
6525543B
BUZZER
FRONT
VEHICLE
HARNESS
Without Vehicle Harness
BUZZER 2-PIN
CONNECTOR
BACK-UP SENSOR
HARNESS 2-PIN
CONNECTOR
VEHICLE
PANEL
2-PIN
CONNECTOR
WIRE TIE
WITH CLIP B
VEHICLE
PANEL
6525554B
FRONT
BUZZER
WIRE TIE
BUZZER
HARNESS
VEHICLE
HARNESS 10 of 13
AII 32953 (0609)
© 2006 American Honda Motor Co., Inc. All Rights Reserved
36. At the rear corner of the vehicle, remove the vehicle
grommet.
37. Route the back-up sensor subharness 6-pin
connector through the hole where the vehicle
grommet was removed and seat the grommet of the
back-up sensor subharness grommet in the vehicle
hole.
38. Install the connector clip to the back-up sensor sub-
harness 6-pin connector.
39. Plug the back-up sensor subharness 6-pin
connector into the back-up sensor harness 6-pin
connector, and install the connector clip into the
vehicle panel hole in the area shown.
6227010B
FRONT
BACK-UP SEN-
SOR HARNESS 6-
PIN
VEHICLE GROMMET
(Discard.)
BACK-UP SENSOR
SUBHARNESS
BACK-UP SENSOR
SUBHARNESS
GROMMET
cabin side
outside
6227020B
FRONT
BACK-UP SENSOR
SUBHARNESS
6-PIN CONNECTOR
BACK-UP SENSOR
HARNESS 6-PIN
CONNECTOR
BACK-UP
SENSOR
HARNESS
HOLE
VEHICLE
PANEL
BACK-UP SENSOR
SUBHARNESS
6-PIN CONNECTOR
BACK-UP
SENSOR
SUBHARNESS
CONNECTOR
CLIP
40. Route the back-up sensor subharness as shown,
and install the back-up sensor subharness clip into
the vehicle panel hole. Secure the back-up sensor
subharness:
With Rear bumper Beam: Using isopropyl alcohol
on a shop towel, clean the rear bumper beam where
the cable clip will attach. Insert the back-up sensor
subharness into the holder of the cable clip. Remove
the adhesive backings from the cable clip, and at-
tach the cable clip to the rear bumper beam as
shown.
Without Rear Bumper Beam: Install the back-up
sens