Below is a cache of http://snow.he.net/~fesmith/search/PDF_Files/TGL-XX.pdf. It's a snapshot of the page taken as our search engine crawled the Web.
The web site itself may have changed. You can check the current page or check for previous versions at the Internet Archive. Yahoo! is not affiliated with the authors of this page or responsible for its content.
TGL Series Tree Grate Up light
FOR LANDSCAPE ARCHITECTURE
IRONSMITH
(800) 338-4766
Tempered glass window
Stainless Yoke Assembly
Allows 28 Degree rotation
from vertical
35 watt MR16 Lamp housing
Wet Location rated
Drop in Housing
needs only 7" depth
below Tree grate walking
surface
Fits Standard
IRONSMITH

Lightwell
Cast faceplate
same finish and
material as grate
TREE GRATE UP LIGHTS
Catalog Id
Lamp Type
Lamp Voltage
Beam Spread
TGL-20F
20 Watt MR16 Halogen
12 volt
40 degree flood
TGL-20S
20 Watt MR16 Halogen
12 volt
12 degree spot
TGL-35F
35 Watt MR16 Halogen
12 volt
40 degree flood
TGL-35S
35 Watt MR16 Halogen
12 volt
12 degree spot

Lamp Holder: Machined 6061-T6 aluminum
cap attached to a machined 6061-T6
aluminum body using one 8 -18 stainless steel
set screw, and sealed with a high temperature
silicone o-ring. Cap and body are black
anodized. An 1/8 thick, tempered, clear lens
is secured to cap with a high temperature, UV
curing, silicone adhesive. Lamp holder is
supplied with 6 of 16-2 cable. Cable exit
sealed with a water tight strain relief fitting.
Aiming: Lamp holder is attached to 304
stainless steel bracketry, allowing 29� vertical
aiming.
Cover Plate: mounts to aiming bracket with
8-18 stainless steel hardware, ensuring that
lens opening is properly aligned. 1/4 thick,
tempered, clear lens, secured to cover plate
with a high temperature, UV curing, silicone
adhesive. Cover is supplied with tree grate and
is the same material and finish as tree grate.
Socket: GY-6.35 porcelain socket with
600V, 250�C, PTFE coated 18 ga leads
Lamp: Bi-pin MR16 up to 35 watts
Certification: CSA tested & certified for
35W Max MR16 lamp to US and Canadian
safety standards for wet location landscape
use per UL1838, CSA TILB-58B, CAN/CSA
C22.2 No.9.*
* Not for use underwater or in fountains
Connect :
To any remote 12 volt transformer
system.
A low voltage uplight solution specifically designed for Ironsmith Tree Grates
Fits : All Ironsmith Tree grates with 9 1/2" round or
square lightwells. ( currently does not fit: Grates
under 48"; Del Sol or Conquistador pattern grates ) 1.1250
7" Nom.
To Low Voltage
Transformer
Tree Grate
Lamp Housing
Aiming bracket
Adjust angle
as desired
Lightwell Cover
with Glass Lens
Bracket scews to
undeside of cover
Outer Shield
Drops into Lightwell Opening
Power cord
Leave enough slack
in cord to allow removal
of fixture for relamping
Gravel to promote drainage
in poor draining soils
41-701 Corporate Way #3
Palm Desert, CA 92260
(800) 338-4766
(760) 776-5080 Fax
IRONSMITH
This drawing embodies a confidential proprietary design of IRONSMITH,IN. Palm Desert,Ca. All design, manufactuing ,reproduction ,use,
sale, and pother rights regarding the same are expressly reserved. This drawing is submitted under confidential relationship for a specific
purpose and the recipient agrees by accepting this drawing not to supply or disclose any information regarding it to any unauthorized
person or to incorporate any special feature peculiar to this design in other projects. The information in this drawing may be covered
completely or in part by partentspending.
TGL Series
Low Voltage Tree grate
Up Light
Cover is shipped
installed in tree grate
Lamp Assembly with
housing bracket and
shield are shipped
separately.
Use 12 volt 35Watt
Max MR16 lamp.
(supplied with lamp of
choice)
Outer sheild must be
used to keep earth
away from Lamp
Housing and prevent
overheating.
If Sheild is to be
partially burried place a
bed of gravel at the
sheild base sufficient to
keep the light well clear
of standing water and
to help minimize
intrusion of dirt.
Connect fixtures to
appropriate 12 volt
transformer of your
choice. (Not Supplied)
Cover design will vary depending on tree grate selected Leadershi
p
b
y

I
I
R
R
O
O
N
N
S
S
M
M
I
I
T
T
H
H


































T
T
G
G
L
L


S
S
E
E
R
R
I
I
E
E
S
S


U
U
P
P


L
L
I
I
G
G
H
H
T
T


ARCHITECTURAL PRODUCTS

INSTALLATION INSTRUCTIONS

IRONSMITH, INC. 41-701 Corporate Way # 3 Palm Desert, CA 92260 Phone (760) 776-5077
Phone (800) 338-4766 Fax (760) 776-5080 Email:
info2u@ironsmith.biz
INSTRUCTIONS PERTAINING TO RISK OF FIRE, OR INJURY TO PERSONS

WARNING! To reduce the risk of FIRE OR INJURY TO PERSONS
1.
Do not touch luminaire while lamp is on. Turn off/unplug and allow to cool before replacing lamp.
2.
Lamp gets HOT quickly! Contact only switch/plug when turning on.
3.
Do not touch hot lens, faceplate, body, or cap.
4.
Keep lamp away from materials that may burn.
5.
Do not touch lamp at any time. Use a soft cloth. Oil from your skin may damage lamp.
6.
Do not operate the luminaire with damaged or missing parts.
7.
Do not disassemble lamp housing beyond cap removal to facilitate lamp replacement
8.
Remove any debris accumulated on the faceplate, in the housing, or in the body fins when necessary.
9.
Do not install luminaire within 10 feet of a pool, spa, or fountain.
10. Have fixture installed in accordance with all applicable installation codes and standards by a person familiar with the construction and operation of the
fixture and the hazards involved.
11. Use only cable rated for low voltage. Cable buried more than 6 must be suitable for direct burial.
12. Use only lamps rated for this fixture. 12 volt 35 watt maximum MR16

SAVE THESE INSTRUCTIONS

INSTALLATION
1.
If preinstalled, remove light well cover from tree grate.
2.
With tree grate installed, excavate under light opening to the depth of the Shield ( About 7 below grade) enough to allow shield to drop fully into
grate.
3.
In poor draining soils, excavate an additional 3 below bottom of shield and fill space to bottom of shield with gravel for drainage.
4.
Attach lamp housing and Yoke Assembly to the Cover Plate with the three screws provided
5.
feed Supply Cable through Shield.
6.
Drop Shield into tree grate opening insuring it seats fully on lip.
7.
Connect Supply Cable to 16-2 Cable on fixture. Allow enough cable length to permit complete removal of Assembly from Light well for re-lamping.
Ensure power being supplied is appropriate to fixture.
8.
Insert Cover Plate with Lamp Assembly into Light well and secure with screw.

AIMING OF FIXTURE
1.
Caution! Fixture will be hot if lamp is on.
2.
Remove Cover plate screw and lift assembly out of tree grate.
COVER PLATE
YOKE ASSEMBLY
YOKE SCREW(3)
LAMP HOUSING TOP
SET SCREW
LAMP
LAMP HOUSING
BASE
SILICON O-RING
SHIELD
GRATE
3.
Loosen Vertical Aiming Screws
4.
Adjust Yoke as desired
5. Tighten
Screws
6.
Replace Assembly in Light well opening.


RE-LAMPING
1.
Remove power from fixture and let cool before touching.
2.
Remove Cover Plate with attached assembly from tree grate.
3.
Separate Yoke Assembly from Cover Plate by removing three screws.
4.
Loosen Set Screw on lamp housing. Do NOT remove set screw!
6.
Pull
amp my still be hot! Be sure lamp
7.
Push
pins are properly aligned. Be sure
8.
Insta
g Top by slowly twisting and pushing. Due to
9.
Seat Top fully and tighten set screw until it just bottoms out. Do NOT
10. Rem
tree grate.
5.
Remove Lamp Housing Top by slowly twisting and pulling to reduce
risk of damage to O-Ring.
lamp straight out. Caution! L
has cooled before touching.
new lamp straight in. Be sure
correct Lamp wattage is used. See inside lamp housing for
Lamp ratings.
ll Lamp Housin
tight O-Ring seal you will notice resistance as air pressure
builds up.
over tighten set screw! Distortion of the housing can allow
moisture in causing fixture failure.
ount Yoke to Cover and Reinstall in



Web: ironsmith.biz