Webmasters « back to results for ""
Below is a cache of http://www.world-electronics.com/Manuals/T3.pdf. It's a snapshot of the page taken as our search engine crawled the Web.
The web site itself may have changed. You can check the current page or check for previous versions at the Internet Archive. Yahoo! is not affiliated with the authors of this page or responsible for its content.
Untitled
This is Your Software Security Access Key:
DO NOT LOSE IT !









DO
DO NOT
NOT PLUG
PLUG THE
THE SECURITY
SECURITY KEY
KEY INTO
INTO ANY
ANY
ELEVATOR
ELEVATOR INTERFACE
INTERFACE PORT
PORT

This security device must be plugged into the notebook
computers PRINTER port whenever the FREEDOM Tool
Software is to be run.
List of Trademarks



List of Trademarks

Windows is a trademark / product of Microsoft Corporation.
Microsoft is a registered trademark.
Traflomatic III and Traflomatic IV are trademarks of Dover Elevator Systems, Inc.
IBM is a trademark of International Business Machines Corporation
WORLD electronics, the WORLD electronics' logo, FREEDOM Tool, and FREEDOMWare are registered
trademarks of WORLD electronics Sales and Service, Inc.





















Copyright
©
1997-2003 by WORLD electronics®. All rights reserved. Printed in the United States of America.
Except as permitted under the United States Copyright Act of 1976, no part of this publication may be reproduced or
distributed in any form or by any means, or stored in a data base or retrieval system, without the prior written
permission of WORLD electronics. Further, this publication and features described herein are subject to change
without notice from the publisher.
Table Of Contents
WORLD electronics
Introduction.................................................................................................................................... 1
Features ....................................................................................................................................... 1
Requirements ............................................................................................................................... 1
How to Contact WORLD electronics ............................................................................................ 2
Getting Started............................................................................................................................... 3
Security Device Information ......................................................................................................... 3
Executing the FREEDOM Tool Shell Software (Windows 3.1) .................................................... 3
Executing the FREEDOM Too Shell Software (Windows 95) ...................................................... 4
Starting the T-III module from the FREEDOM Tool Shell Software ............................................. 6
General Description ...................................................................................................................... 9

Car Diagnostics Module.............................. 12
Power On.................................................... 13
Power Off ................................................... 14
Car Diagnostic Window ........................... 16
Adjustments / Timers / Displays ............... 17
Speed Profile ....................................... 18
The Adjustment Window.............. 20
The Timer Window........................ 23
The Display Window..................... 26
Door ..................................................... 28
Emergency Operation .......................... 29
Machine ............................................... 30
Audio and Visual Output ...................... 30
Security Operation ............................... 31
Start-Up / Set-Up ................................. 32
Digital Loadweigher ............................. 33
Miscellaneous ...................................... 34
Job Information......................................... 36
Control Status Words ............................... 39
Terminal System Set-Ups......................... 42
Resets....................................................... 44
Hoistway Setup ......................................... 45
Registering Car and Hall Calls.................. 49
Faults ........................................................ 53


Group Diagnostic Module ..................... 56
Power On .............................................. 57
Power Off .............................................. 58
Group Diagnostic Window................. 60
System Adjustments............................ 62
Car / Group Adjustments..................... 63
Timers ................................................. 64
Displays ............................................... 65
Job Parameter Information.................. 67
Control Status Words .......................... 70
Registering Hall Calls .......................... 72
Hall Call Lockout ................................. 76
Code Blue Calls................................... 78
Faults................................................... 82
Reference Elevator.............................. 84
Designation.......................................... 85
Resets ................................................. 87









File................................................................................................................................................... 91
Save ............................................................................................................................................. 91
Restore......................................................................................................................................... 93
Exit................................................................................................................................................ 94
Self-Test ......................................................................................................................................... 95
Appendix A: Adjustment /Timer / Display Guide ....................................................................... 96

Introduction
WORLD electronics Page 1
Introduction:


The FREEDOM Tool is a sophisticated software tool which allows the operator to service various elevators and
elevator control systems. The software allows the operator to simultaneously view independent operations within
the elevator system by opening windows to those systems / operations of interest. The selected windows may then
be left open during the maintenance / repair session and accessed when desired.

This Users Guide and Reference has been written to specifically target the Dover Traflomatic-III elevator control
system. Any and all references to
FREEDOM Tool throughout this manual implies that it pertains solely to the
software Systems that support the Dover Traflomatic-III elevator control systems.

FREEDOM Tool Features:

The FREEDOM Tool is a Graphical User Interface (GUI) and provides all the functions necessary to service the
Dover Traflomatic-III elevator systems. The software runs under the Microsoft Windows operating system and
provides the following features:
A Graphical User Interface which makes it easy to access various adjustment and diagnostic areas
comprising the service tool resident upon the Dover Traflomatic-III elevator
control system being diagnosed.
System adjustment parameters for the elevator system being diagnosed are presented in terms that are
the industry standards within the elevator industry.
Operating information pertinent to a particular elevator site may be Saved or Restored at any time
through the use of the File command within the Main selection window.

Minimum Hardware and Software Requirements:

The software is provided as a package by WORLD electronics and is meant to be operated on an IBM compatible
Notebook computer which has the following minimum characteristics:
A 486 microprocessor. 4 Megabytes of RAM memory. Windows 3.1 Operating System. Mouse, Trackball, or other pointing device. Minimal clock frequency of 33MHz Internal Fax/Data Modem

The FREEDOM Tool software is not capable of being executed without a sophisticated
security key which is to be
connected to the parallel port of the computer at the time of the FREEDOM Tool execution.

A
WORLD electronics FREEDOM Tool Serial Interface Cable and a FREEDOM Tool T-III Interface Card are
required. These interfaces provide the proper signal