OG LIGHTS
PARTS LIST
Fog Light Kit (sold separately)
P/N 08V31-SCV-100
2 Fog lights
Switch harness
Fog light harness
Relay
Fuse label
20 Wire ties
13 Wire ties with clip
8 Self-tapping screws
Fog Light Switch Kit (sold separately)
P/N 08V31-SCV-110A (black)
P/N 08V31-SCV-120A (gray)
Switch
TOOL AND SUPPLIES REQUIRED
Phillips screwdriver
Flat-tip screwdriver
Ratchet
10 mm socket
File
Drill
3 mm and 20 mm Drill bits
Utility knife
Diagonal cutters
Pushpin
Hacksaw blade
Clip remover
08V31-SCV-1000-91
2422021K
SWITCH
HARNESS
SWITCH
RELAY
FOG LIGHT
FOG LIGHT
HARNESS
FOG
LIGHT
FUSE
CASE
(20A)
INSTALLATION
Customer Information: The information in this
installation instruction is intended for use only by
skilled technicians who have the proper tools,
equipment, and training to correctly and safely add
equipment to your vehicle. These procedures should
not be attempted by do-it-yourselfers.
NOTE: This installation instruction shows the left fog
light being installed; the same procedure applies to
installing the right fog light.
1.
Make sure you have the anti-theft code for the
radio, then write down the frequencies for the
preset buttons.
2.
Disconnect the negative cable from the battery.
AII 24288
Illustration of the Fog Lights Installed on the Vehicle
www.collegehillshonda.com/parts 2 of 13
AII 24288 (0212)
© 2002 American Honda Motor Co., Inc - All Rights Reserved.
Installing the Fog Light
3.
Open the hood and remove the radiator cover (five
clips).
5.
Inside the front bumper, locate the three marks on
the fog light housing on the left side. Using a
pushpin, pierce the bumper at the center of each
mark. While wearing eye protection, drill a 3 mm
pilot hole then finish with a 20 mm hole through
the bumper at the center of each mark.
4.
Remove the front bumper (seven clips at the top,
six clips and four stepped bolts at the bottom and
one self-tapping screw on each side).
6.
While being careful not to scratch the bumper, use
a hacksaw blade to cut out the marked area from
the front bumper along the inside of the scribed
line and the groove on the back. Remove all burrs
from the edges of the cutout.
2328091K
CLIP
RADIATOR
COVER
2328101K
CLIPS (7)
FRONT
BUMPER
SELF-
TAPPING
SCREWS (2)
STEPPED
BOLTS (4)
CLIPS
(6)
2329011K
FRONT
BUMPER
PUSHPIN
DRILL BITS
(First drill
with a 3 mm
bit, and
finish with a
20 mm bit).
MARKS (3)
FOG LIGHT
HOUSING
2329023K
Cut out.
SCRIBED LINE
FRONT
BUMPER
GROOVE
SECTIONAL VIEW
Cut out. © 2002 American Honda Motor Co., Inc - All Rights Reserved.
AII 24288 (0212)
3 of 13
7.
Inside the front bumper, slide the fog light into the
cutout you made, and secure it with four self-
tapping screws.
10. Locate the 1-pin connector blue-taped to the
vehicle harness and remove the blue tape to free
the 1-pin connector. Connect the 1-pin connector
you just freed to the fog light harness 1-pin
connector .
11. Loosen the ground bolt that fastens the vehicle
ground terminal and secure the fog light harness
ground terminal using this ground bolt.
12. Secure the fog light harness 1-pin connector and
the fog light harness to the vehicle harness with
one wire tie. Do not secure the 1-pin connector to
the SRS harness with the wire tie.
2403021K
FOG LIGHT
HARNESS
FOG LIGHT HARNESS
GROUND TERMINAL
GROUND
BOLT
2402011K
WIRE TIE
FOG LIGHT
HARNESS 1-PIN
CONNECTOR
FOG LIGHT
HARNESS
SRS
HARNESS
Routing the Fog Light Harness
9.
Starting under the left headlight, route the fog light
harness 1-pin connector and ground terminal
through the hole in the front bulkhead.
8.
Repeat steps 5 thru 7 to cut the bumper and
install the fog light on the right side of the bumper.
2329030K
FOG LIGHT
FRONT
BUMPER
SELF-TAPPING
SCREWS (4)
2403010K
BLUE
TAPE
FOG LIGHT
HARNESS
1-PIN
CONNECTOR
FOG LIGHT
HARNESS
GROUND
TERMINAL
VEHICLE 1-PIN
CONNECTOR
LEFT FRONT
BULKHEAD
PANEL
FOG LIGHT
HARNESS 4 of 13
AII 24288 (0212)
© 2002 American Honda Motor Co., Inc - All Rights Reserved.
2417070K
2418010K
2409050K
2403030K
13. Behind the front side frame, route the fog light
harness 2-pin connector (short end) down, and out
through the clearance between the side frame and
front bumper beam. Attach the wire tie with clip to
the fog light harness at the green tape, then push
the clip into the hole in the side frame.
14. Route the fog light harness 2-pin connector (long
end) up along the bulkhead side stay, then along
the vehicle harness behind the front bulkhead
upper frame.
15. Continue routing the fog light harness 2-pin
connector forward, then down to the bottom of the
front side frame along the outside of the right
bulkhead side stay.
16. Align the green tape on the fog light harness
(closest to the connector) with the hole in the front
lower cross member, then secure the harness to
the hole with the wire tie in the area shown.
LEFT FRONT
SIDE FRAME
GREEN
TAPE
WIRE TIE
WITH CLIP
FOG LIGHT
HARNESS 2-PIN
CONNECTOR
(SHORT END)
FRONT BUMPER
BEAM
FRONT BULKHEAD
UPPER FRAME
VEHICLE
HARNESS
FOG LIGHT
HARNESS
FOG LIGHT
HARNESS
RIGHT
BULKHEAD
SIDE STAY
FOG LIGHT
HARNESS 2-PIN
CONNECTOR
FRONT SIDE
FRAME
FOG LIGHT
HARNESS
FOG LIGHT
HARNESS
WIRE TIE
FRONT LOWER
CROSS MEMBER
GREEN
TAPE
FRONT BUMPER
BEAM © 2002 American Honda Motor Co., Inc - All Rights Reserved.
AII 24288 (0212)
5 of 13
17. Attach the three wire ties with clips to the fog light
harness at the green tapes, then push the clips
into the holes in the bulkhead side stay. Further
secure the fog light harness to the vehicle harness
with two wire ties in the areas shown.
If the vehicle is equipped with an engine block
heater:
Secure the engine block heater and fog light harnesses
to the bulkhead side stay with the wire ties on the
engine block heater harness and two wire ties with
clips on the fog light harness.
18. Secure the fog light harness to the vehicle
harness with six wire ties in the areas shown.
19. Secure the fog light harness to the holes in the
bulkhead side stay and the side frame with four
wire ties with clip.
20. Secure the fog light harness to the front bulkhead
area with the wire tie with clip, and to the vehicle
harness with one wire tie.
21. Secure the fog light harness to the hole under the
front side frame with one wire tie with clip.
2418050K
FOG
LIGHT
HARNESS
WIRE TIE
WITH CLIP
WIRE TIE
LEFT FRONT
SIDE FRAME
WIRE TIE
WITH CLIP
LEFT
BULKHEAD
SIDE STAY
LEFT FRONT
BULKHEAD
2418041K
WIRE TIE
WIRE TIE
FOG LIGHT
HARNESS
WIRE TIE
WITH CLIP
2418022K
WIRE TIE
FOG LIGHT
HARNESS
WIRE TIE
WITH CLIP (3)
GREEN
TAPE
FOG LIGHT
HARNESS
RIGHT
BULKHEAD
SIDE STAY
2418031K
FOG LIGHT
HARNESS
WIRE TIE WITH CLIP
ON FOG LIGHT HARNESS
ENGINE BLOCK
HEATER HARNESS
WIRE TIE ON
ENGINE BLOCK
HEATER
RIGHT
BULKHEAD
SIDE STAY 6 of 13
AII 24288 (0212)
© 2002 American Honda Motor Co., Inc - All Rights Reserved.
22. While holding the front bumper near the front of
the vehicle, plug the fog light harness 2-pin
connectors into the 2-pin connectors from the fog
lights. Reinstall the front bumper.
24. Remove the center dashboard lower cover (two
expansion clips, two clips and four retaining tabs).
NOTE: This illustration shows the center lower cover
with subwoofer. Remove the center lower cover without
subwoofer the same way.
Routing the Switch Harness
23. Remove the drivers dashboard lower cover, turn
the knobs clockwise, then pull the cover out
toward you to release the six retaining tabs.
2418061K
FOG LIGHT
2-PIN
CONNECTOR
FOG LIGHT
HARNESS
2-PIN
CONNECTOR
FOG LIGHT
FRONT BUMPER
FOG LIGHT
FOG LIGHT
HARNESS
2-PIN
CONNECTOR
2403050K
RETAINING
TABS (6)
KNOB
DRIVERS
DASHBOARD
LOWER
COVER
2403062K
RETAINING
TABS (4)
EXPANSION
CLIPS (2)
CENTER
DASHBOARD
LOWER COVER
CLIPS (2) © 2002 American Honda Motor Co., Inc - All Rights Reserved.
AII 24288 (0212)
7 of 13
25. Starting from behind the instrument panel, route
the switch harness 8-pin connectors down along
the vehicle harness. On the left of the instrument
panel frame, unplug the vehicle 8-pin connectors
(gray), and plug the switch harness 8-pin
connectors in between the switch harness
connectors and the vehicle connector.
26. Slide the switch harness 8-pin connector onto the
holder on the vehicle 8-pin connector (gray).
27. Locate the 1-pin connector blue-taped to the
vehicle harness and remove the blue tape to free
the connector. Plug the vehicle harness 1-pin
connector into the switch harness 1-pin connector
(blue/red).
28. At the fuse box, plug the switch harness
1-pin connector (white/red) into the fuse box in the
location shown.
2404011K
SWITCH
HARNESS
SWITCH
HARNESS 8-PIN
CONNECTOR
VEHICLE 8-PIN
CONNECTOR
(GRAY)
HOLDER
2403072K
VEHICLE 8-PIN
CONNECTOR
(GRAY)
INSTRUMENT
PANEL FRAME
VEHICLE
CONNECTOR
(Cruise
control
system
equipped
only.)
INSTRUMENT
PANEL
SWITCH
HARNESS
2404022K
SWITCH HARNESS
1-PIN CONNECTOR
(BLUE/RED)
VEHICLE
HARNESS
BLUE TAPE
VEHICLE 1-PIN
CONNECTOR
SWITCH
HARNESS
2405010K
FUSE BOX
SWITCH
HARNESS 1-PIN
CONNECTOR
(WHITE/RED)
SWITCH
HARNESS
1-PIN CONNECTOR
CONNECTING PORT
SWITCH
HARNESS 8-PIN
CONNECTOR 8 of 13
AII 24288 (0212)
© 2002 American Honda Motor Co., Inc - All Rights Reserved.
30.
On M/T only: Plug the switch harness 6-pin
connector into the fuse box.
29.
On A/T