2650
SOLAR HOUSE ADDRESS
PANEL WITH NUMBERS SKU 92650 For technical questions, please call 1-800-444-3353.

Page 2
Specifications
Save This Manual
You will need the manual for the safety warnings and precautions, assembly
instructions, operating and maintenance procedures, parts list and diagram.
Keep your invoice with this manual. Write the invoice number on the inside of the
front cover. Keep the manual and invoice in a safe and dry place for future
reference.
Safety Warnings and Precautions
WARNING: When using product, basic safety precautions should always be
followed to reduce the risk of personal injury and damage to equipment.
Read all instructions before using this product!
1.
Keep work area clean. Cluttered areas invite injuries.
2.
Observe work area conditions. Keep work area well lit.
3.
Check for damaged parts. Before using any product, any part that
appears damaged should be carefully checked to determine that it will
perform its intended function. Check for any broken or damaged parts and
any other conditions that may affect its operation. Replace or repair
damaged or worn parts immediately.
4.
Replacement parts and accessories. When servicing, use only identical
replacement parts. Use of any other parts will void the warranty.
5.
Always check hardware and assembled parts after assembling. All
connections should be tight and hardware tightened.
6.
Keep children away. Children must never be allowed in the work area.
7.
Dress Properly. Wear restrictive hair covering to contain long hair.
8.
Use eye protection. Always wear ANSI approved impact safety goggles
when setting up this product.
9.
Maintain products with care. Keep the Solar Address Panel clean for
better performance. Follow instructions for set up. Inspect periodically. If
damaged, have it repaired by an authorized technician.
Materials
Wall Bracket Dimensions
Battery Type
Solar Panel
Net Weight
Brass Frame, Poly Plastic Reflector Board, Polystyrene Window Cover
3.62 L x 1 W
One AA Rechargeable Ni-Mh Battery
2.12 L x .75 W (3 Solar Panels)
1.20 Lb. SKU 92650 For technical questions, please call 1-800-444-3353.

Page 3
10. Do not overreach. Keep proper footing and balance at all times when
installing Solar Address Panel.
11. Do not set up the Solar Address Panel if under the influence of alcohol
or drugs. Read warning labels on prescriptions to determine if your judgement
or reflexes are impaired while taking drugs.
12. Wipe away snow or debris on the Solar Address Panel. If Solar Address
Panel is covered with snow for an extended period of time, allow weather to
clear. At this time the batteries need to charge in direct sunlight for at least 6-
8 hours in order to perform at its full capacity.
13. Use only Batteries of the type recommended.
14.
Do not mix old and new batteries.
15. The battery should be Nickel-Cadmium rechargeable.
16. Remove the battery if the Solar Address Panel is not used for a long
period of time.
17. Keep the Solar Address Panel free of dirt, dust, grime, snow and debris.
Dust covering the Solar Panel will block out sunlight causing a
decrease or stoppage of efficiency in recharging the battery.
18. Dispose of used batteries at a recommended Waste Disposal Site provided
by your local community.
Warning: The warnings, cautions, and instructions discussed in this instruc-
tion manual cannot cover all possible conditions and situations that may oc-
cur. It must be understood by the operator that common sense and caution
are factors which cannot be built into this product, but must be supplied by
the operator.
Unpacking
When unpacking the Solar Address Panel, check to make sure that all parts
are included as shown in the parts list. If any parts are missing or broken,
please call Harbor Freight Tools at the number below. SKU 92650 For technical questions, please call 1-800-444-3353.

Page 4
1.
Remove the Solar House Address Panel from the box. To Illuminate, the
battery should be fully charged. Place the Solar House Address Panel in the
sunlight for at least 24 hours.
2.
After charging the battery, you can put your house numbers on the Reflector
Board (6) by disassembling the contents on a smooth surface. Remove the
Screws (10) from the Back Board (8), using a Philips Head Screwdriver (not
provided). Remove the small screw on the side/center of the Copper Panel
Cover (1). Set hardware aside. Remove the Back Board, the Reflector Box
(7) with the Electronic Circuit (3), and the Reflector Board (6).
Note: Be
careful when setting the Electronic Circuit assembly aside, so as not to
stretch the wiring.
See Figure A .
3.
With the Reflector Board (6) out, select the numbers from the Number
Stickers (12). Peel back plastic backing from numbers and place on the
Reflector Board (6). If placing on inside of the panel, be sure you reverse the
order so the address reads correctly when placed back in frame.
See Parts
Identification on Page 7. See Figure B on page 5.
Assembly of House Numbers
Choosing a Location
1.
An outdoor location with full, direct sunlight is the best position for the Solar
Address Panel. Shadowy locations will not allow the battery to charge fully
and will reduce the hours of lighting at night.
2.
Do not place near a night time light source such as a porch light or street
light. This could cause the Solar Address Panel to turn off automatically.
3.
If choosing a front gate as a location, attach the Panel on a wall near the
gate or on a Ground Stake that receives sunlight at least 6-8 hours a day.
Check periodically to make sure panel does not come loose over time.
Figure A
Screws (10)
Back Board (8)
Reflector Box (7)
Copper Panel
Cover (1)
Small Screw SKU 92650 For technical questions, please call 1-800-444-3353.

Page 5
Reflector Board (6)
Figure B
Copper Panel
Cover (1)
4.
Replace the Reflector Board (6) and the Reflector Box (7), including
Electronic Circuit (3), positioning as before, being careful not to stretch or
crimp wires.
See Figure B.
1.
Please Note: There is a pull-off Tab (5) around the connection of the
Battery (4) which blocks battery operation. This Tab allows the Battery to be
in an OFF position. It is used during storage. Save this Tab for future use.
Remove the Battery (4), and Tab (5), replace the Battery (4), and securely
make contact from the Battery (4) to the terminal.
See Figures C & D.
Removing the Tab to Activate Battery
Tab (5)
Battery (4)
Tab (5)
Figure C
Figure D
Terminal SKU 92650 For technical questions, please call 1-800-444-3353.

Page 6
5.
The Solar Address Panel will automatically turn ON at dusk and OFF at
dawn after a 24 hr. charge time.
See Figure F.
2.
Replace the Back Board (8) and secure with the Screws (10). Be careful not to
stretch or strain wires. Make sure you have returned the side/center screw into
place.
See Figure E.
Figure E
Screws (10)
Back Board (8)
Small Screw
3.
Be sure you have positioned every part (except the removable Tab) just as
the Solar House Address Panel was originally assembled.
4.
Locate the Solar House Address Panel in the desired position (see mounting
instructions on next page). If the light does not turn on after 24 hours of
charging, check the battery to ensure that it is making secure contact with
the terminal. Also check that the Solar Address Panel is in a bright sunny
location and not in the shade. Recharging time should be at least 6-8 hours
in sunlight.
Figure F SKU 92650 For technical questions, please call 1-800-444-3353.

Page 7
Warning: Dispose of battery in a recommended Waste Disposal Site in
your community. Do not open, short circuit, or mutilate batteries as
injury may occur.
1.
Remove the Solar Address Panel from the wall or ground stake.
2.
Use a screwdriver to remove the Screws (10) on the Back Board (8).
Remove the old Battery (4). Replace it with a new AA Ni-Mh battery.
Reconnect exactly as it was connected, being careful not to stretch or strain
wiring.
See Figure G.
3.
Attach the Back Board (8) with the Screws (10) and replace on your wall.
1.
Mark the holes on the Wall Holder (9) to the desired surface with a pencil.
2.
A power drill (not included) is used to drill the holes. The distance between
the holes is 1-7/8 inches apart, center to center. Warning: When drilling, be
sure there are no electrical wires or cables in the drill path. Be sure the holes
you drill are level. Use the orange Wall Anchors provided for anchoring into
dry wall or plaster.
3.
Leave Screw heads sticking out 1/5 from the wall to hang the back of the
Solar Address Panel onto. Hang the attached Solar Address Panel Wall
Holder (9) on the exposed Screws.
Attaching the Solar Address Panel to a Wall
Maintenance
1.
To remove dust, use a damp cloth. To remove grease or oil, use a detergent
based cleaning solvent, rinse with damp cloth, and dry.
Replacing the Battery
Battery (4)
Copper Panel
Cover (1)
Figure G
Screws (10)
Back Board (8) SKU 92650 For technical questions, please call 1-800-444-3353.

Page 8
PLEASE READ THE FOLLOWING CAREFULLY
THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS DIAGRAM IN THIS MANUAL AS
A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER NOR DISTRIBUTOR MAKES ANY
REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS QUALIFIED TO
MAKE ANY REPAIRS TO THE PRODUCT OR THAT HE OR SHE IS QUALIFIED TO REPLACE ANY PARTS OF
THE PRODUCT. IN FACT, THE MANUFACTURER AND/OR DISTRIBUTOR EXPRESSLY STATES THAT ALL
REPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN BY CERTIFIED AND LICENSED
TECHNICIANS AND NOT BY THE BUYER. THE BUYER ASSUMES ALL