nt> « back to results for ""
Below is a cache of http://www.darksavior.net/~james/LVDS-01RGB-01.pdf. It's a snapshot of the page taken as our search engine crawled the Web.
The web site itself may have changed. You can check the current page or check for previous versions at the Internet Archive. Yahoo! is not affiliated with the authors of this page or responsible for its content.
LVDS-01 Module Easy Guide for Your Easy Use


1

LVDS-01 Module Easy Guide for Your Easy Use
Rev 1.0

VIA LVDS-01 is a module designed for the EPIA Mini-iTX series mainboards to support
LCD panel displays. Models that comply are EPIA M, EPIA M2 and EPIA CL.

l
Specifications

LVDS Transmitter Chip: Chrontel 7019A - includes programmable dithering to
support 18-bit and panel
Single channel support, with resolutions up to 1024 x 768
Connector pin-definitions and jumper settings
1.
Signal connector (LVDS_PANEL) pin definition
PIN
SIGNAL
PIN
SIGNAL
1 A4M (Differential signal)
2 PVDD (+3.3V/+5V)
3 A4P (Differential signal)
4 PVDD (+3.3V/+5V)
5 GND
6 GND
7 A5M (Differential signal)
8 GND
9 A5P (Differential signal)
10 A0M (Differential signal)
11 GND
12 A0P (Differential signal)
13 A6M (Differential signal)
14 GND
15 A6P (Differential signal)
16 A1M (Differential signal)
17 GND
18 A1P (Differential signal)
19 CLK2M (Differential signal) 20 GND
21 CLK2P (Differential signal)
22 A2M (Differential signal)
23 GND
24 A2P (Differential signal)
25 A7M (Differential signal)
26 GND
27 A7P (Differential signal)
28 CLK1M (Differential signal)
29 NC
30 CLK1P (Differential signal)
31 NC
32 GND
33 NC
34 A3M (Differential signal)
35 NC
36 A3P (Differential signal)
37 NC
38 SPCLK
39 NC
40 SPDAT
2.
Inverter connector (INVERTER_CONN) pin definition
PIN
SIGNAL
PIN
SIGNAL
1 IVDD (+12V/+5V)
2 IVDD (+12V/+5V)
3 BLON (Backlight ON)

4 NC
5 BLON (Backlight ON)
6 NC
7 GND
8 GND



2
3.
Jumper settings
NOTE: Wrong voltage settings may damage your panel or inverter.


(1) PVDD_SEL: Set to 3.3V or 5V to match
the voltage required by the LCD


(2) IVDD_SEL: Set to 5V or 12V to match the
voltage required by the inverter


Approved LCD Panels

LG LP150X04-A2M1

LG LP150X04-D2

LG LP150X1

LG-Philips LP141XA

Hannstar HSD141PX11-A

Torisan TM121XG-02L01

Sharp LQ150X1LC77

AU A201SN01


l
Assembly instructions

In the LVDS-01 package, you will find:
(1) LVDS-01 module x 1
(2) Screws x 2
(3) Washers x 2
(4) Power cable for panel x 1
(5) LVDS-01 Easy Guide x 1

The following assembly instructions are based on the EPIA M Mini-iTX mainboard.
For EPIA MII and EPIA CL, the relative screw positions are the same.

99-51-012741


3
1. EPIA M mini-iTX motherboard and LVDS-01 module



2. Line up the screw-fixing holes of the LVDS-01 module with the screw-fixing holes on
the Dual heatsink. The screw-fixing holes are indicated by red circles above.

3. Fix the screws to the indicated holes. For each hole, add a washer in between the
module and the heatsink.




4
4. Connect the panel and inverter cables to the corresponding connecters.
NOTE: The cables are not included in our package. Check your panel side for
them.



5. Connect the panel power cable, one side onto the LVDS-01 (+12V_CONN) and the
other side onto the FAN3 connecter on the motherboard.


6. Done! Now your EPIA M mini-iTX motherboard supports LVDS.





1

RGB-01 Module Easy Guide for Your Easy Use
Rev 1.0

VIA RGB-01 is a module designed for the EPIA Mini-iTX series mainboards to support
TTL panel displays. Models that comply are EPIA M, EPIA MII and EPIA CL.

l
Specifications

Support 18-bit panels
Connector pin-definitions and jumper settings
1.
Signal connector (LVDS_PANEL) pin definition
PIN
SIGNAL
18-bit PIN
SIGNAL
18-bit
1 GND

2 GFPCLK
(Display clock)

3 GFPHS (Horizontal sync.)

4 GFPVS (Vertical sync.)

5 GND

6 GFPD18
R0
7 GFPD19
R1
8 GFPD20
R2
9 GFPD21
R3
10 GFPD22
R4
11 GFPD23
R5
12 GND

13 GFPD10
G0
14 GFPD11
G1
15 GFPD12
G2
16 GFPD13
G3
17 GFPD14
G4
18 GFPD15
G5
19 GND

20 GFPD2
B0
21 GFPD3
B1
22 GFPD4
B2
23 GFPD5
B3
24 GFPD6
B4
25 GFPD7
B5
26 GND

27 GFPDE (Display enable)

28 PVDD (+3.3V/+5V)

29 PVDD (+3.3V/+5V)

30 R/L (Horizontal display
mode select signal)

31 U/D (Vertical display
mode select signal)

32 GFPD0


33 GFPD1

34 GFPD8

35 GFPD9


36 GFPD16

37 GFPD17

38 GND

39 GND

40 GND

2.
Inverter connector (INVERTER_CONN) pin definition
PIN
SIGNAL
PIN
SIGNAL
1 IVDD (+12V/+5V)
2 IVDD (+12V/+5V)
3 BLON (Backlight ON)

4 NC
5 BLON (Backlight ON)
6 NC
7 GND
8 GND



2
3.
Jumper settings
NOTE: Wrong voltage settings may damage your panel or inverter.


(1) PVDD_SEL: Set to 3.3V or 5V to match
the voltage required by the LCD



(2) IVDD_SEL: Set to 5V or 12V to match the
voltage required by the inverter



l
Assembly instructions

In the RGB-01 package, you will find:
(1) RGB-01 module x 1
(2) Screws x 2
(3) Washers x 2
(4) Power cable for panel x 1
(5) RGB-01 Easy Guide x 1

The following assembly instructions are based on the EPIA M Mini-iTX mainboard.
For EPIA MII and EPIA CL, the relative screw positions are the same.


99-51-012741


3
1. EPIA M mini-iTX motherboard and RGB-01 module


2. Line up the screw-fixing holes of the RGB-01 module with the screw-fixing holes on
the Dual heatsink. The screw-fixing holes are indicated by red circles above.

3. Fix the screws to the indicated holes. For each hole, add a washer in between the
module and the heatsink.




4
4. Connect the panel and inverter cables to the corresponding connecters.
NOTE: The cables are not included in our package. Check your panel side for
them.



5. Connect the panel power cable, one side onto the RGB-01 (+12V_CONN) and the
other side onto the FAN3 connecter on the motherboard


6. Done! Now your EPIA M mini-iTX motherboard supports RGB.