inet_9741.pdf. It's a snapshot of the page taken as our search engine crawled the Web.
The web site itself may have changed. You can check the current page or check for previous versions at the Internet Archive. Yahoo! is not affiliated with the authors of this page or responsible for its content.
Installation Instructions 9741-1-CA/WB ENTERTAINMENT CABINET Installation Instructions
9741-1-CA/WB
ENTERTAINMENT CABINET 9741-1-CA / WB
ENTERTAINMENT CABINET
1. Level
2. Phillips head screw driver
3. Allen head wrench (provided)
Tools Required
Included
1. Two 50mm bolts
2. Allen head wrench
3. Two 5/8 wood screws Attaching the Deck to the Console
This product ships in two-pieces for easier in-home delivery and set up.
1.
Place the lower console into position and level it utilizing the leveler
adjusters under the four corners of the base.
2.
Move the lower console away from the wall so you can access the rear
side of the cabinet. Note: Now is a good time to plug the surge
suppressor power cord into a nearby wall outlet.
3.
Set the deck unit on top of the lower console.
4.
Align the rear edge and corners of the deck unit to match up with the
rear edge and corners of the lower console.
5.
Open the doors in the lower console, locate the bolt holes in the sub-top
which lead to the underside of the LH and RH columns of the deck unit,
select two 50mm bolts (provided), insert the bolts thru the sub-top of the
lower console and into the threaded inserts located in the bottom ends of
the LH and RH columns of the deck unit. Lightly tighten bolts with Allen
wrench provided.
UPPER UNIT
50mm BOLT
ALLEN WRENCH
LOWER UNIT 6.
Mending plates are included to help prevent the deck unit from
accidentally falling forward and potentially hurting someone or severely
damaging the deck unit. Locate these mending plates near the lower
edge of the deck unit back panel. Loosen the screw that secures these
mending plates to the back panel and rotate one end of the mending
plate downward so it bridges the top edge of the lower console.
7.
Insert one 5/8" wood screw thru one of the screw holes in the mending
plate that is positioned behind the rear edge of the lower console back
rail and screw it in place with a Phillips head screw driver.
8.
Re-position the console and deck against the wall.
9.
Reverse these steps to disassemble these units prior to moving the
product a greater distance. Do not move this product in an assembled
format.
Attaching the Deck to the Console...cont.
MENDING PLATE
SCREWS
LOWER UNIT
MENDING PLATE
UPPER UNIT SPECIAL FEATURES
S M A R T E Y E
WHAT IS IT?
The SmartEye enables Sligh to maintain the design integrity of the cabinet with-
out sacrificing appearance for function.
It is designed to allow remote control of electronic components stored behind
closed doors.
SmartEye does not come with its own remote. Instead it works
with previously purchased universal remotes or the standard remote that
comes with your electronic component.
For example: You can adjust the volume or sound track on your DVD player by
pointing your hand held remote at the signal receiver on the face of the cabinet
and pressing the appropriate control button on your remote. All while you are
sitting on your sofa watching the TV screen!
HOW IT WORKS
The SmartEye includes an external signal receiver, internal control box, internal
signal emitters and a power cord/transformer.
SIGNAL RECEIVER
Typically located in a cross rail just under the top of the cabinet. It receives and
transmits a signal from your hand held remote to a signal emitter located near the
electronic component storage shelf.
Simply aim your hand held remote at this eyelet.
Note:
1. A green or red light appears inside the signal receiver
to alert you that your command is being transmitted.
2. This system functions with IR (infrared) remotes only.
It does not function with RF (radio frequency) remotes.
3. The SmartEye will transmit a signal within 20 of your remote.
CONTROL BOX
Typically located on the inside face of the back panel or
under the top surface. Its purpose is to be a power source
and help transmit the actual signal from your hand held
remote to the electronic component.
Signal emitter cords, the signal receiver cord and the power
cord are all plugged into the control box.
SIGNAL EMITTERS
Small round electronic devices that are located on the face of the
inside end panels near the component storage shelves. It transmits
the actual signal to the sensors located inside your electronic
components.
Note:
The face of your electronic component must be positioned
behind the round signal emitters for the SmartEye to func
tion. The number of emitters varies depending on the number
of storage shelves included inside the cabinet. Almost all cabinets
have at least 2 emitters. Some cabinets have as many as 8 emitters.
Signal Emitters
Control Box
Signal Receiver SPECIAL FEATURES
S M A R T E Y E . . . c o n t .
POWER CORD
It is plugged into the control box when received by the customer.
The other end includes a transformer-box plug that is intermin-
gled with the power cord for the surge suppressor. Plug this end
into a nearby wall outlet prior to placing the TV console against the
wall. The power cord for the surge suppressor must also be plugged
into a nearby wall outlet to be operable.
Note:
The SmartEye will not function unless the power cord is correctly
plugged in at both ends. Check to be sure this is the case prior to
attempting operation.
Power Cord
CONFIGURATION
Control Box
Signal Emitters
Power Cord
Signal Receiver
D I S P L A Y L I G H T S
Replacing a light bulb
1. Remove the lens cover by twisting it counter clock wise.
2. Replace the bulb by simply pulling out the old and
replacing it with the new bulb.
3. Then replace the lens cover by twisting it clock wise.
NOTE: Some lens covers may be flush to the cabinet which
will not give you enough room to grab the cover with your
fingers. If so, use a screwdriver or key to gently insert into
one of the slots in the lens cover and then turn gently.
TO ORDER: www.furnlite.com. S U R G E S U P P R E S S O R
M U L T I F L E X M E D I A D R A W E R
Includes 5 power plug outlets, indicator light,
optional satellite TV cord, optional co-ax cable.
Protection level: 720 joules, includes breaker
Each drawer is designed to accommodate
CDs, DVDs etc. in an organized flexible man-
ner with the use of Velcro bottom moveable
dividers and storage stops.
Arrange as preferred. Each drawer
comes with
Two dividers
Two stops
SPECIAL FEATURES Sligh Furniture Company Holland, Michigan www.sligh.com 9741 6/07