lor=black> Below is a cache of http://www.spyder.tv/section/support/manuals/spyder_electra_dx.pdf. It's a snapshot of the page taken as our search engine crawled the Web.
The web site itself may have changed. You can check the current page or check for previous versions at the Internet Archive. Yahoo! is not affiliated with the authors of this page or responsible for its content.
ELECTRA DX
ELECTRA DX
14010 Live Oak Avenue, Baldwin Park, CA 91706, U.S.A.
Telephone: 626-430-2300 Fax:626-851-8530
Website: www.kingman.com
JAVA 9.6V RECHARGEABLE BATTERY & CHARGER INCLUDED
Kingman Group 14010 Live Oak Avenue, Baldwin Park, CA 91706, U.S.A.
Toll-free 888.KINGMAN
www.kingman.com CAUTION
This paintball marker is NOT a toy. It can cause serious injury or death.
Recommend at least 18 years of age to purchase this product.
Install a barrel plug in the barrel when not actually playing.
All persons using this product, or within range while this product is being used,
must wear eye and face protection specifically designed for paintball.
Never shoot a person who is not wearing proper protection.
Treat every paintball marker as if it were loaded.
Never look down the barrel of the marker.
Keep the paintball marker on safe until ready to shoot.
Always remove gas source before disassembly.
Fire only 0.68 caliber paintballs from this product.
Read this manual and air system warning before using this product.
Transfer this instruction manual upon change of marker ownership.
IMPORTANT

Firing velocity may vary according to altitude and climate conditions.
BEFORE using your marker in play, you must always first perform a
SAFE VELOCITY TEST. This can only be accomplished by using a testing device
called a Velocity Chronograph and can be performed by the dealership where you
purchased this product or at a local paintball playing field.
NOTE: This product is intended to be used at a velocity no greater than
300 feet per second (FPS).
Recommended velocity is 280 FPS or less.
This product is NOT intended to be used at any distance less than 25 feet.
This paintball marker may have excess gas after removal of the tank. Please remove all
paintballs and discharge the remaining gas safely.
CO2/HP AIR TANK WARNING
WARNING
VALVES MUST BE INSTALLED OR REMOVED ONLY BY QUALIFIED PERSONNEL.
BOTTLE MUST BE RETESTED SEE CO2/HP TANK LABEL FOR RETEST DATE!
Improper use, filling, storage or disposal of this cylinder may result in death, personal
injury and property damage.
This cylinder must be filled only by properly Trained personnel in accordance with CGA
Pamphlets P.1 and G-6.3 available from the Compressed Gas Association
www.CGANET.COM
Do not over pressurize. Do not expose pressurized cylinder to temperatures in excess of
130 degrees F.
Do not expose cylinder to corrosive materials and do not clean with caustic cleaners.
Do not alter this cylinder in any way.
Cylinders heated to a temperature of 250 degrees For more must be condemned or re-
qualified in accordance with test defined in CFR-49.
Keep cylinder out of reach of children.
The valve should NEVER be detached from the canister. Should this occur, please seek
assistance from a trained airsmith immediately.
This tank is intended for paintball use only.
P1 26A
2317
RF17B
RF17C
RF17A
22
21
2547
2547A
23F
23FA
2529
2529A
29B
24A
27
27A
09
01
02KB
02KC
2508 / 2508C
2508N
2508NA
2544H
2544HA
2544F
2544FA
37K
37D
42F
37A
37C
37B
2535K
2535KA
36C/36E
36E/36C
2535
2535C
35E
36D
36D
37C
09
09
10A
11
12
13
14
05C
05C
39D
23C
05A
04GA
20
2504
2504A
09
09
07
15
23B
2506
2506A
09
09
09
09
JE29
JE31C
49C
JE31F
JE26
E29E
JE29
JE1015
JE27
25
18B
19A
JE30B
35D
33F
33F
JE18E
JE12
JE31E
E24
E33
49B
49
JE
18C
JE31D
16/16D
16/16D
JE33C/JE33D
JE33C/JE33D
JE33C/JE33D
JE32A/JE32
Spyder Electra & Electra DX
(Matte Black and Matte Blue)
P2
P3
SPYDER Electra and Electra DX Parts List
ITEM #
NAME OF PARTS
ITEM #
NAME OF PARTS
01
Spyder Barrel Plug
27
Striker Spring Guide
02KB
Electra 13.5" Barrel (Black)
27A
Flat Disc
02KC
Electra 13.5" Barrel (Blue)
29B
Lock Screw
04GA
Mini Detent Cover (Black)
E29E
LED Circuit Board
05A
M4 x 6 Screw (Black)
2529
Thumb Adjuster w/ Screw (Black)
05B
M4 x 6 Screw (Silver)
2529A
Thumb Adjuster w/ Screw (Blue)
05C
Direct Feed Screw
33F
Compact Nut Screw
07
M5 X 14 Screw w/ Washer
35D
Spyder Gauge
09
O-Ring #015 80D
35F
Regulator Lock Screw
10A
Valve Spring
2535K
Electra Drop Forward (Black)
11
Cup Seal Guide
2535KA
Electra Drop Forward (Blue)
12
Cup Seal
36C
5/32" X 7/8" Screw (Silver)
13
Valve Pin
36D
5/32" x 5/8" Screw (Black)
14
Valve Body
36E
5/32" X 7/8" Screw (Black)
15
Valve Body Screw
37A
Filter O-Ring
16
M5 x 12 Screw (Black)
37B
Air Filter
16D
M5 x 12 Screw (Silver)
37C
Disconnect O-Ring #011 (Black)
2317
Electra Venturi Cocking Bolt
37D
Plastic Washer
RF17A
Retaining Screw
2537
Electra Disconnect Hose
RF17B
Retaining Spring
39D
Electra Striker Knob
RF17C
Retaining Ball
2541
Electra Spare Parts Kit
JE18A
Striker
42
Male To Male Adapter
19A
Striker O-Ring
42F
C/A Male Adapter
20
Barrel O-Ring (Black)
2547
Electra Sight Rail (Black)
21
Bolt Pin
2547A
Electra Sight Rail (Blue)
2504
Direct Feed (Black)
49
Trigger Roll Pin
2504A
Direct Feed (Blue)
49B
Secondary Sear Roll Pin
2506
Electra Receiver (Black)
49C
Touch Switch Roll Pin
2506A
Electra Receiver (Blue)
E24
On/Off Switch with Wiring Harness
2508
Vertical Adapter (Black)
E24A
Battery Harness
2508C*
Vertical Adapter w/ Gauge (Blue)
E33
On/Off Screw (M2 x 6 Screw)
2508N
Low Pressure Chamber (Black)
E40
Straight Elbow - 2 3/4"(Clear)
2508NA
Low Pressure Chamber (Blue)
JE1015
Java 9.6v Rechargeable Battery
23F
Striker Plug (Black)
JE12
Trigger Sear
23FA
Striker Plug (Silver)
JE18C
Coil Set
2535
C/A Adapter (Black)
JE18E
Coil Set Screw
2535C*
C/A Adapter w/ Regulator (Blue)
JE26
Charge Pin
2544F
Mini Fore Grip (Black)
JE27
Touch Switch
2544FA
Mini Fore Grip (Blue)
JE29
Circuit Board Screw
2544H
Model S Expansion Chamber (Pewter)
JE30B
Tournament Lock Switch
2544HA
Model S Expansion Chamber (Silver)
JE31C
Trigger
21
Bolt Screw
JE31D
Trigger Adjust Screw
22B
M4 X 8 Screw w/Washer (Black)
JE31E
Sear Spring
23B
Quick Disconnect Pin
JE31F
Trigger Spring
23C
Disconnect Pin Lock
JE32
Grip Cover (Black)
24A
Sight Rail Screw w/ washer
JE32A
Grip Cover (Clear)
25
Striker Spring
JE33C
Grip Cover Screw (Black)
26A
Striker Buffer
JE33D
Grip Cover Screw (Silver)
*
For Electra DX Model Only. Put the marker on 'SAFE' by pushing the on/off switch to the right. The marker is now off. To
power on the marker, push the on/off switch to the left. CAUTION: with the power on, the
electronic circuit board is now powered on and ready to shoot.
Cock the marker by pulling the Cocking Knob (#39D) rearward until it latches. Caution: if you let
go before it latches, your marker may fire.
Tighten the air tank until it is snug. If a leak occurs between the tank and the C/A adapter,
replace the tank o-ring.
Install a 7/8th vertical elbow with loader onto the direct feed. Fill the loader with .68 caliber
paintballs only.
With the safety off, fire the marker by pulling the trigger.
Only use lubrication specifically designed for paintball markers. To lubricate your marker, you will
need to disassemble your marker (please note how parts are removed from marker as this will
ease re-assembly). Remove the Disconnect Lock Pin (#23C) and the Quick Disconnect Pin
(#23B). Hold down the Striker Plug (#23F/#23FA) and Thumb Adjuster (#2529 #2529A), as
internal parts may be spring-loaded. As you pull the cocking knob out of the receiver, the Venturi-
Cocking Bolt (2317) and striker (JE18A) will also be removed.
Lubricate o-rings #9B and #19A with a few drops of paintball oil only.
Re-assemble parts back into the marker. Note: when putting the Venturi-Cocking Bolt and striker
back into the marker, you will need to apply pressure behind the bolt while Pushing the sear
(#JE12) forward to its limit at the same time. (right now the battery side grip must be opened )
This will allow the bolt and striker to be properly installed back into the receiver.
When you are finished shooting the marker, first, unload the marker of all paintballs (also see
#10 below). NOTE: there may be a ball in the receiver; take a couple of shots in a safe direction
to make sure that the barrel and receiver are empty. Second, put the barrel plug into the barrel.
Put the safety on and slowly unscrew the air source tank. Caution: do not unscrew the tank
valve from the tank. Doing so may cause serious injury or death.
Empty the hopper or remove the hopper off the marker to stop the flow of paintballs in the
marker.
Adjusting the regulator To adjust the regulator, turn the regulator screw (#35E) clockwise to
increase the pressure (500~600 psi is recommended). When your nitrogen or compressed air
system is properly installed to the C/A adapter (#2535, #2535C), the recommended output
pressure of the air system should be at 750 ~ 850 psi.
Adjusting the trigger pull You may adjust the trigger pull on your marker by turning the
Trigger Adjust Screw (JE31D). Follow these steps to access the trigger adjust screw:
(1) Remove the two frame screws (#16/#16D) that connect the grip frame
to the receiver.
(2) Look inside the trigger frame to find the Trigger A