can you build?
Students learn that there are two types of circuits: series and parallel. They build both types of circuits
and observe the differences between them. They apply their understanding of series and parallel
circuits to understanding how circuits are designed for different purposes such as a bell in cars that
warns the driver that the door is open.
A-3 Current and Voltage
How are current and voltage measured in a circuit?
Students learn how to use an electrical meter to measure current and voltage in a circuit. Through their
measurements, they learn that voltage drops in a circuit as work is done (lighting a bulb) while current
does not change in the same circuit.
Level B Investigations
B-1
Voltage
Why do charges move through a circuit?
In this Investigation, students explore how a battery works and what the term volt means. They
measure voltage across a battery alone, and then while it is in a circuit lighting a bulb. They also
discover that the charges in a circuit with more than one battery can only flow when opposite ends of
the batteries are lined up (positive to negative, or negative to positive).
B-2
Current
How does current move through a circuit?
Students learn that you can increase the amount of energy in a circuit in two ways. The higher the
current value, the more energy that can be carried. The higher the voltage, the more energy that can be
carried by the same amount of current.
B-3
Ohms Law
How are voltage, current, and resistance related?
In this Investigation, students discover one of the fundamental relationships in electricity: Ohms law.
They discover this relationship by measuring current, resistance, and voltage in a circuit. They graph
voltage vs. current and find out that the slope of the graph is equal to the resistance. Level C Investigations
C-1 Series Circuits
How do you use Ohms law in series circuits?
In this Investigation, students learn how to calculate total resistance in a series circuit. They also use
Ohms law to determine the resistance of a bulb at different levels of current using a potentiometer.
They discover that the resistance of the bulb increases as current increases.
C-2 Parallel Circuits
How do parallel circuits work?
Students build parallel circuits and measure their electrical quantities. They determine how total
current and branch currents are related in parallel circuits. Finally, they build a test voltage circuit like
the ones used in portable medical devices. These circuits alert you when battery voltage has dropped.
C-3 Compound Circuits
How do you analyze compound circuits?
In this Investigation, students build and analyze compound circuits. They determine the current at
different points in a compound circuit. They also calculate the total resistance in the circuit. 1
B-2
B-2
Current
Question: How does current move through a circuit?
Why does a bulb light? When you put a battery in a circuit, electric current flows through the wires and
makes things happen. The current carries energy from the battery to a bulb or motor. You can increase
the amount of energy in two ways. The higher the value of the current, the more energy that can be
carried. The higher the voltage, the more energy that can be carried by the same amount of current.
Safety Tips: Be careful working with batteries. If they are damaged or broken, return
them immediately to your teacher.
If a battery or wire gets hot, disconnect the circuit and ask your teacher for help.
A
Building test circuit #1
1. Gather the following materials: electrical meter and its two test leads, a
battery and battery holder, a bulb and bulb holder, and two connectors.
2. Build test circuit 1 with one battery and battery holder, one bulb and bulb
holder, and two connectors, as shown in the schematic at right. There are
two points marked on the schematic, A and B, which is where the
connectors are attached to the bulb holder. Make sure that you can easily
identify these points in your circuit.
B
Measuring current through test circuit #1
To measure current, the meter must be placed in the circuit so that the current has to flow through it.
Follow the instructions below carefully.
1. Connect the two meter leads to the meter as
shown at right.
2. Set the meter to measure DC current at the
highest range.
3. Remove the connector between the positive
terminal of the battery and the bulb holder.
4. Place the red positive lead of the meter on the
post attached to the positive terminal of the
battery.
5. Place the black negative lead of the meter on the
free post attached to the bulb holder. You should
now have a complete circuit. The bulb should
light and you should get a reading on the meter.
6. Record the current at point A.
7. Reconnect the circuit and then disconnect it at point B.
In this Investigation, you will:
1. Measure and compare current at different points in a circuit.
2. Compare current in circuits with one and two bulbs. 2
B-2
8. Predict what the current at point B will be. Record your prediction.
9. Following the same procedure you did for point A, use your meter to measure current at point B.
The positive lead of the meter should be closest to the positive battery terminal, and the negative
lead of the meter should be closest to the negative battery terminal.
10. Record the current at point B.
11. Remove the meter and reconnect the circuit. Leave it connected while you complete part 3.
C
Building test circuit #2
1. Gather the following additional materials: one battery and battery holder,
two bulbs and bulb holders, and three connectors.
2. Build the circuit in the diagram at right. Make sure that you can easily
identify points A, B, and C where the connectors are attached.
D
Comparing test circuits #1 and #2
Compare the brightness of the bulbs in test circuits 1 and 2. Record your observations.
E
Measuring current through test circuit #2
1. Using the same procedure you followed in part 2, measure and record current at point A.
2. Predict what the current will be at points B and C.
3. Using the same procedure you followed in part 2, measure and record current at points B and C.
F
What did you learn?
a.
Review the two current readings for circuit 1. What conclusions can you draw from these results?
b.
Review the three current readings for circuit 2. What conclusions can you draw from these results?
c.
Transfer all your results for circuit 1 and circuit 2 into the table below. Compare the current readings in
the two circuits. What happened to current when you added a bulb to the circuit?
d.
You probably determined that adding a bulb to the circuit reduced the current. With the rest of your
group propose an explanation. Be prepared to present and defend your explanation.
Current in circuit 1 (amps)
Current in circuit 2 (amps)
point A

point A

point B

point B



point C
B-2 Current
Answer Sheet
B-2
B-2
Current
Question: How does current move through a circuit?
Safety Tips: Be careful working with batteries. If they are damaged or broken, return
them immediately to your teacher. If a battery or wire gets hot, disconnect the circuit
and ask your teacher for help.
A
Building test circuit #1
No responses are required in part 1.
B
Measuring current through test circuit #1
Record the current at point A.
Predict what the current at point B will be. Record your prediction.
Record the current at point B.
C
Building test circuit #2
No responses are required in part 3.
D
Comparing test circuits #1 and #2
Compare the brightness of the bulbs in test circuits 1 and 2. Record your observations here:








Name: B-2 Current
Answer Sheet
B-2
E
Measuring current through test circuit #2
1. Record current at point A here:
2. Predict what the current will be at points B and C:
3. Record current at points B and C here:
F
What did you learn?
a.
Review the two current readings for circuit 1. What conclusions can you draw from these results?
b.
Review the three current readings for circuit 2. What conclusions can you draw from these results?





















B-2 Current
Answer Sheet
B-2


c.
Transfer all your results for circuit 1 and circuit 2 into the table below. Compare the current readings in
the two circuits. What happened to current when you added a bulb to the circuit?
d.
You probably determined that adding a bulb to the circuit reduced the current. With the rest of your
group, propose an explanation. Be prepared to present and defend your explanation.
Current in circuit 1 (amps)
Current in circuit 2 (amps)
point A

point A

point B

point B



point C













B-2 Current
Answer Sheet
B-2
Questions
1.
What is the difference between current and voltage?
2.
What units are used to measure current? What do these units mean?
3.
When you measure the current of a circuit with an electrical meter you insert the meter at one point into
the circuit while the circuit is on. Explain why current must be measured in this way.
4.
Will a circuit with three bulbs have a faster or slower current than a circuit with two bulbs?
5.
In the circuit below, the current at point A is 0.5 amps. What is the current at point B?













Curriculum Resource Guide: Electric Circuits
Curriculum Resource Guide: Electric Circuits
Copyright
2002 Cambridge Physics Outlet
ISBN 1-58892-043-7
2 3 4 5 6 7 8 9 - QWE - 05 04 03
All rights reserved. No part of this work may be reproduced or transmitted in