a x s urge po wer
The meaning of Max output continuous and Max surge power is
that some appliances or tools, such as ones with a motor, require an
initial surge of power to start up (max surge load or max peak load).
Once started, the tool or appliance requires less power to continue
to operate (max output continuous load).
Helpful formulas:
Multiply: Amps x 230 (AC voltage) = Watts
Multiply: Watts x 2 = Surge Power
This formula yields a close approximation of the surge power of the
appliance.
Caution: Induction loads such as compressor, air conditioners,
refrigerators, freezers and pumps may have a greater surge power
of 3~9 times the continuous rating.
If you need inverter to run induction loads, use pure sine wave
inverters.

What type of battery should I use?
For above-mentioned models, most automobile and marine batteries
will provide an ample power supply for hours even when the engine
is off.
Actual time depends on the age and condition of battery. We
recommend you start the engine if you intend to use the inverter for
a long time.

Ap p lia n ces c onne ct io n
Make sure that the maximum current consumption of the appliances
connected to the inverter (ie: notebook, TV, fan, emergency light,
etc.) does not exceed the maximum output power of the inverter
itself.

Ho w t o us e th e i n ve r ter
Put the cigar plug into the cigarette lighter socket (DC12v or 24V) or
directly to the battery. Turn on the power switch; LED indicator will
light up. Then connect the electrical appliance to your inverter.
Caution: Make sure positive pole of DC clip (Red wire +) is
connected to positive pole of battery (Red wire +)
Do no t d r i ve whi le us ing t he a l lig a to r cl ip s wi th th e
in ver te r.

Maint enan ce
Remember to pull all the plugs out of the socket when cleaning and
clean inverter with dry cloth only.
Caution: Water and damp are not acceptable near or on the
inverter.
Do not open the inverter.

Genera l S a f e t y P re ca ut io ns Do not expose the Inverter to rain, snow, spray, bilge or dust.
To Reduce risk of hazard, do not cover or obstruct the
ventilation openings.
Do not install the Inverter in a zero-clearance compartment.
Overheating may result.
To avoids a risk of fire and electronic shock. Make sure that
existing wiring is in good electrical condition; and that wire size is
not undersized. Do not operate the Inverter with damaged or
substandard wiring.
E xp los i ve Ga s P reca u ti ons
This equipment contains components, which can produce arcs or
Sparks. To Prevent fire or explosion do not install in compartments
batteries or Flammable materials or in locations which require ignition
protected equipment. This includes any space containing gasoline-
powered machinery, fuel tanks, or joints, fittings, or other connection
between components of the fuel system.

P reca ut io ns W hen W or king W ith Ba t ter ies

If battery acid contacts skin or clothing, wash immediately with soap
and water. If acid enters eye, immediately flood eye with running cold
water for at least 20 minutes and get medical attention immediately. NEVER smokes or allow a spark or flame in vicinity of battery or
engine. Do not drop a metal tool on the battery. The resulting
spark or short-circuit on the battery or other electrical part may
cause an explosion. Remove personal metal items such as rings, bracelets,necklaces,
and watches when working with a lead-acid battery. A lead-acid battery produces a short-circuit current high enough to
weld a ring or the like to metal, Causing a severe burn.













2/4
w w w. n a u t i ch a r g e r. co m



WARNING!
Operation of the inverter without a
proper ground connection may
result in an electrical safety hazard.


WARNING!
Shock Hazard. Before proceeding.
Further, ensure that the Inverter is
NOT connected to any Batteries,
and that all wiring is disconnected
from any electrical Sources.
Do not connect the output
Terminals of the Inverter to an
incoming AC sources. The inverter
will be damaged permanently, not
covered by our warranty.


WARNING!
Make sure all the DC connections
are tight (torque to 9-10 ft-lbs,11.7-
13Nm). Loose connections will
overheat and could result in a
potential hazard.


CAUTION!
Reverse polarity connection will
blow a fuse in Inverter and may
permanently damage the inverter.
Damage caused by reverse polarity
connection is not covered by our
warranty.



WARNING !
You may observe a spark when you
make this connection since current
may flow to charge capacitors in
the power inverter.
Do not make this connection in the
presence of flammable fumes,
explosion or fire may result.

WARNING!
Do not open or disassemble
Inverter, attempting to service the
unit yourself may result in a risk of
electrical shock or fire.

Installation: Where to install
The power inverter should be installed in a location that meets the
following requirements: Dry Do not allow water to drip or splash on the inverter. Cool Ambient air temperature should be between 0 degrees
and 40 degrees C. Do not place the inverter in direct sunlight if
avoidable. Safe Do not install in a battery compartment or other areas
where flammable fumes may exist, such as fuel storage are as or
engine compartments. Ventilated Allow at least one inch of clearance around the
inverter for air flow. Ensure the ventilation openings on the rear
and bottom of the unit are not obstructed. Dust-free Do not install the Inverter in a dusty environment
where either dust, wood particles or other filings/shavings are
present. These can pulled into the unit when the cooling fan is
operating. Close to battery/batteries Avoid excessive cable lengths but
do not install the Inverter in the same compartment as batteries.
Use the recommended wire lengths and sizes. Also do not mount
the Inverter where it will be exposed to the gases produced by the
battery. These gases are very corrosive and prolonged exposure
will damage the Inverter.


AC safety Grounding
During the AC wiring installation, AC input and output ground wires are
connected to the inverter. The AC input ground wire must connect to
the incoming ground from your AC utility source.
The AC output ground wire should go to the grounding point for
your loads ( for example, a distribution panel ground bus ).



The installation of the inverter
must comply with your
countries electrical current
regulations of the appliance




CAU TIO N

1. Please do not use the inverter if the DC input source is not 12Vdc
for the 12V inverters or 24Vdc for the 24V inverters, and appliances
are not 230Vac (220-240 Vac).
2. When you stop using it, please pull out the plug. Because of the high
temperature of the metal part, do not touch the plug by hand or place
it near flammable and easy-melting materials.
3. Under Voltage Protection system will automatically switch off the
inverter if the input voltage is too low. Please start the engine to
charge the battery, or stop using it.
4. If the consumption power is over inverter power rate itself, when
switching on appliances, a protection system will indicate the
overload.
5. Due to the difference of the waveform, buzzing and lines on audio
and video equipment might appear.
6. How to select cigar plug or alligator clip for use:
(1) Cigar-Lighter: use with electric equipment below 150 Watt output.
(2) Alligator clips: use with electric equipment over 150 Watt output.
7. We recommend you should use pure sine wave inverter on very
sensitive test equipment.
8. Do not use the inverter if the power cable or plug is damaged or
loose.
9. Do not put any object into the inverter: it may cause fire, electric

3/4
w w w. n a u t i ch a r g e r. co m

shock or short circuit; if there is any abnormal noise, smell or
smoke, please turn it off immediately, then contact your retailer.
10. Do not place any heavy object on the inverter or on the power
cable. Do not use it when the power cable is coiled or bent
sharp.
11. Do not allow water drip or splash on the inverter. Do not touch
the case or the plug with wet hands.
12. Do not attempt to alter the structure or the power cable: it may
cause electric shock or fire; please contact your retailer for internal
checking if necessary.

U np a cking a nd ins p e ct ion
Before starting, please check this carton should contain following
items: inverter, users manual, cigar plug or power cables. Should
any of above-mentioned items be missing, please contact your local
dealer immediately.






MODIFIED SINE WAVE













TECHNICAL SPECIFICATIONS
(*)

Model
FPE
150W-12V

FPE
300W-12V

FPE
500W-12V

FPE
700W-12V
FPE
1000W-12V
FPE
1000W-24V
FPE
1500W-12V
FPE
1500W-24V
Max Output
Continuous
Watt 150
Watt 300
Watt 500
Watt 700
Watt 1000
Watt 1000
Watt 1500
Watt 1500
Max Surge
Power
Watt 300
Watt 600
Watt 1000
Watt 1400
Watt 2000
Watt 2000
Watt 3000
Watt 3000
DC Input
Voltage
12/10~15V
dc
12/10~15Vdc 12/10~15Vdc 12/10~15Vdc 12/10~15Vdc 24/20~30Vdc 12/10~15Vdc 24/20~30Vdc
AC Output
Voltage
220 220 220 220 220 220 220 220
Modified
Sine Wave
yes yes yes yes yes yes yes yes
Efficiency
>85% >85% >85% >85% >85% >85% >85% >85%
Frequen