COMBI-Modul 167/ phyPS-404
d>
COMBI-Modul 167/ phyPS-404
A product of a PHYTEC Technology Holding company
k i
h
d
C
h l i
ldi
AG
COMBI-Modul 167
phyPS 404
Hardware Manual
Edition April 2002
COMBI-Modul 167 phyPS-404
PHYTEC Me遲echnik GmbH 2002 L-540e_2
In this manual are descriptions for copyrighted products that are not explicitly
indicated as such. The absence of the trademark (
) and copyright (
) symbols
does not imply that a product is not protected. Additionally, registered patents and
trademarks are similarly not expressly indicated in this manual.
The information in this document has been carefully checked and is believed to be
entirely reliable. However, PHYTEC Me遲echnik GmbH assumes no responsibil-
ity for any inaccuracies. PHYTEC Me遲echnik GmbH neither gives any guarantee
nor accepts any liability whatsoever for consequential damages resulting from the
use of this manual or its associated product. PHYTEC Me遲echnik GmbH re-
serves the right to alter the information contained herein without prior notification
and accepts no responsibility for any damages which might result.
Additionally, PHYTEC Me遲echnik GmbH offers no guarantee nor accepts any
liability for damages arising from the improper usage or improper installation of
the hardware or software. PHYTEC Me遲echnik GmbH further reserves the right
to alter the layout and/or design of the hardware without prior notification and
accepts no liability for doing so.
Copyright 2002 PHYTEC Me遲echnik GmbH, D-55129 Mainz
Rights - including those of translation, reprint, broadcast, photomechanical or
similar reproduction and storage or processing in computer systems, in whole or in
part - are reserved. No reproduction may occur without the express written con-
sent from PHYTEC Me遲echnik GmbH.
EUROPE
NORTH AMERICA
Address:
PHYTEC Technologie Holding AG
Robert-Koch-Str. 39
D-55129 Mainz
GERMANY
PHYTEC America LLC
255 Ericksen Avenue NE
Bainbridge Island, WA 98110
USA
Ordering
Information:
+49 (800) 0749832
order@phytec.de
1 (800) 278-9913
info@phytec.com
Technical
Support:
+49 (6131) 9221-31
support@phytec.de
1 (800) 278-9913
support@phytec.com
Fax:
+49 (6131) 9221-33
1 (206) 780-9135
Web Site:
http://www.phytec.de
http://www.phytec.com
2
nd
Edition April 2002
Inhalt
PHYTEC Me遲echnik GmbH 2002 L-540e_2
Preface...........................................................................................................1
1
Introduction to the COMBI-Modul 167 ............................................1
1.1 Overview.......................................................................................1
1.2 Block Diagram..............................................................................3
1.3 Software Development Tools .......................................................5
2
Components on the COMBI-Modul 167 ...........................................7
2.1 Power Supply................................................................................7
2.2 Digital Inputs and Outputs............................................................8
2.2.1
24 V Inputs IN0..IN23.....................................................8
2.2.2
Relay Outputs ................................................................10
2.2.3
24 V Outputs..................................................................11
2.2.4
PWM Outputs ................................................................13
2.3 Analog Inputs and Outputs .........................................................14
2.3.1
Analog Inputs ................................................................14
2.3.2
Analog Outputs..............................................................15
2.4 I睠 Bus........................................................................................16
2.4.1
Real-Time Clock (RTC) ................................................16
2.4.2
I睠 EEPROM.................................................................17
2.4.3
Temperature Sensor.......................................................18
2.5 Interfaces on the COMBI-Modul 167 ........................................19
2.5.1
CAN Interface ...............................................................19
2.5.2
First RS-232 Interface ...................................................20
2.5.3
Second RS-232 Interface...............................................20
2.6 Display and Control Units ..........................................................21
2.6.1
HEX-Encoding Switches S301, S302 ...........................21
2.6.2
DIP Switch S300 ...........................................................22
2.6.3
RUN/STOP Switch........................................................23
2.6.4
Status LEDs ...................................................................23
2.7 Other Components ......................................................................24
2.7.1
RESET ...........................................................................24
2.7.2
Jumper Configuration ....................................................24
2.7.3
Battery............................................................................25
2.7.4
Expansion Connector.....................................................26
2.8 Port Assignment Summary .........................................................27
3
Memory Models .................................................................................33
3.1 Memory Configuration ...............................................................33
3.1.1
Chip Select Signals........................................................33
3.1.2
Chip Select Signal for CODE Flash U4/5 .....................36
3.1.3
Chip Select Signal for SRAM U6/7 ..............................37
3.1.4
Chip Select Signal for DATA Flash U2/3.....................38
3.1.5
Chip Select Signal for External UART .........................39
COMBI-Modul 167 phyPS-404
PHYTEC Me遲echnik GmbH 2002 L-540e_2
3.1.6
Chip Select Signal /CS4 ................................................ 40
4
Hints for Installing the COMBI-Modul 167 ................................... 41
5
Hints for Operating the COMBI-Modul 167.................................. 42
6
Technical Specifications.................................................................... 43
Index............................................................................................................ 47
Index of Figures
Figure 1: Block Diagram COMBI-Modul 167 ............................................ 3
Figure 2: View of the COMBI-Modul 167 (top side).................................. 4
Figure 3: Location of the Function Blocks .................................................. 5
Figure 4: Connecting a Power Supply ......................................................... 7
Figure 5: Circuitry on the 24 V-Inputs......................................................... 8
Figure 6: Input Circuitry Options................................................................. 9
Figure 7: Relay Output Circuitry ............................................................... 10
Figure 8: 24 V Outputs Circuitry ............................................................... 11
Figure 9: PWM Outputs Circuitry.............................................................. 13
Figure 10: Analog Inputs Circuitry.............................................................. 14
Figure 11: Analog Outputs Circuitry ........................................................... 15
Figure 12: HEX-Encoding Switches S301, S302 ........................................ 21
Figure 13: DIP-Switch S300........................................................................ 22
Figure 14: Memory Configuration Example................................................ 34
Inhalt
PHYTEC Me遲echnik GmbH 2002 L-540e_2
Index of Tables
Table 1: I/O Port Arrangement of the 24V Inputs ......................................8
Table 2: Function and I/O Port Arrangement of Relay Outputs ...............10
Table 3: Function and I/O Port Arrangement of 24 V Outputs ................12
Table 4: Accessing the Error Detection State of the 24 V Outputs ..........12
Table 5: LEDs for Output State Control...................................................12
Table 6: Function and I/O Port Arrangement of PWM Outputs...............13
Table 7: Function and I/O Port Arrangement of Analog Inputs ...............14
Ta