l board. Refer to Bulletin E-2101 for
more information about the FLAME-MONITOR system.
26RJ8-5936(T): See Page 2
26RJ8-5873(T): See Page 4
26RJ8-5876(T): See Page 4
26RJ8-5871(T): See Page 3
26RJ8-5874(T): See Page 4
26RJ8-5877(T): See Page 5
26RJ8-5872(T): See Page 3
26RJ8 5875(T): See Page 4
26RJ8-5878(T): See Page 5
Control: E210 for 230
VAC consists of:
E211 for 110 VAC
Consists of:
Programmer Module
Amplifier Module
PFM Adapter
Firetron Cell.
EB720 Chassis
EB721 Chassis
EP113(E)
English text
E1R3
#60-2060-14
#4-263-1
ED510 Display
Module
ED510 Display
Module
EP113(F)
French text
EC600 Dust Cover
EC600 Dust Cover
EP113(D)
German text
EP113(ES)
Spanish text
EP113(SW)
Swedish text
EP113(NL)
Dutch text
PFM-14
JUNE 30, 2005
MODERNIZATION
ADAPTER
#60-2060-14
Fireye Modernization Adapter 60-2060-14 assists with the re-
placement of Fireye 26RJ8 Models listed below using infra-
red flame detection with new solid state modular Fireye
FLAME-MONITOR Burner Management control. 2
26RJ6-5936(T) TERMINAL BOARD WIRING
See Bulletin CX634
4
3
W
NON-RECYCLING INTERLOCKS
L1
REWIRING TO FLAME-MONITOR E210/E211
RECYLING INTERLOCKS
8
LOW FIRE SWITCH
B
HIGH FIRE SWITCH
R
TO BURNER
1
2
5
6
IGNITION TRANSFORMER
PILOT VALVE
L2
230VAC SUPPLY USE E210
110VAC SUPPLY USE E211
MOTOR
2s.
5s.
OR
1
2
IGNITION TRANSFORMER
PILOT VALVE
L2
5
6
NOT
USED
230 VAC
110 VAC
OR
4
L1
LIMIT SWITCH
3
W
OPERATING
CONTROL
R
B
AIR
FLOW
SWITCH
LOW
FIRE
SWITCH 3
®
26RJ6-5936(T) TERMINAL BOARD WIRING
See Bulletin CX634
4
3
W
NON-RECYCLING INTERLOCKS
L1
REWIRING TO FLAME-MONITOR E210/E211
RECYLING INTERLOCKS
8
LOW FIRE SWITCH
B
HIGH FIRE SWITCH
R
TO BURNER
1
2
5
6
IGNITION TRANSFORMER
PILOT VALVE
L2
230VAC SUPPLY USE E210
110VAC SUPPLY USE E211
MOTOR
2s.
5s.
OR
1
2
IGNITION TRANSFORMER
PILOT VALVE
L2
5
6
NOT
USED
230 VAC
110 VAC
OR
4
L1
LIMIT SWITCH
3
W
OPERATING
CONTROL
R
B
AIR
FLOW
SWITCH
LOW
FIRE
SWITCH 4
26RJ6-5936(T) TERMINAL BOARD WIRING
See Bulletin CX634
4
3
W
NON-RECYCLING INTERLOCKS
L1
REWIRING TO FLAME-MONITOR E210/E211
RECYLING INTERLOCKS
8
LOW FIRE SWITCH
B
HIGH FIRE SWITCH
R
TO BURNER
1
2
5
6
IGNITION TRANSFORMER
PILOT VALVE
L2
230VAC SUPPLY USE E210
110VAC SUPPLY USE E211
MOTOR
2s.
5s.
OR
1
2
IGNITION TRANSFORMER
PILOT VALVE
L2
5
6
NOT
USED
230 VAC
110 VAC
OR
4
L1
LIMIT SWITCH
3
W
OPERATING
CONTROL
R
B
AIR
FLOW
SWITCH
LOW
FIRE
SWITCH 5
®
4
3
LIMIT
SWITCH
OPERATING
CONTROL
AIR FLOW
SWITCH
TERMINAL BOARD WIRING 26RJ8-5873T-5874T-5875T-5876T
See Bulletin CX652
L1
1
8
W
LOW FIRE SWITCH
4
3
W
NON-RECYCLING INTERLOCKS
L1
REWIRING TO FLAME-MONITOR E210/E211
RECYLING INTERLOCKS
8
LOW FIRE SWITCH
B
HIGH FIRE SWITCH
R
TO BURNER MOTOR
1
2
5
6
IGNITION TRANSFORMER
PILOT VALVE
L2
230VAC SUPPLY USE E210
110VAC SUPPLY USE E211
2s.
5s.
OR
BURNER
MOTOR
R
L2
W
HIGH FIRE SWITCH 6
Installation Caution: Installer must be trained safety control technician. Verify the
electrical power is disconnected before starting installation.
1.
Loosen the two chassis retaining screws and remove the
chassis from its enclosure. Note the chassis type and
model number
2.
Note the typical circuit diagram figure for complete
information. Rewire terminal board connections as
shown for model replaced.
3.
Install the Modernization Adapter and tighten the two
retaining screws.
4.
Assemble the control and modules and install the
unit into Moderization Adapter. Tighten the chas-
sis retainer
5.
Replace the #4-128 Firetron cell in the scanner with the
#4-263 Firetron cell. Attach the label supplied with the
#4-263 Firetron cell, to the scanner body.
6.
Referring to Fireye Bulletin E2101, turn the power on. Initiate a normal burner start-up and operational test as described for
the E210/E211 Control Unit.
IMPORTANT: If your installation does not have one or more contacts shown in the wiring diagram, it is necessary
that you install them on your burner in order to conform to European codes and regulations. 7
®
FIGURE 1.
1
2
3
4
5
6
7
8
9
W
R
B
10
11
12
13
14
15
M
A
I
N
B
L
O
W
E
R
A
L
A
R
M
S
P
A
R
K
P
I
L
O
T
1
P
I
L
O
T
2
N
220V
L1
LINE
S
C
A
N
N
E
R
REPLACE
FIRETRON
CELL BY
CELL
#4-263-1
PAFS
LFS
AFS
LOC
EXISTING
TERMINAL
BOARD
12
13
5
6
7
8
A
S1
S2
10
11
L1
L2
3
M
D
P
X
LOC:
LIMIT AND OPERATING CONTROL
AFS:
AIR FLOW SWITCH
LFS: LOW
FIRE
START
TO
MODULATOR
CIRCUIT
Typical circuit diagram for modernizing a Fireye 26RJ8 installation using a 60-2060-14 Moderniza-
tion Adapter with a Fireye Flame Monitor, comprised of E-210 Control on ED510 Display Module,
EP113E, F, D, ES, SW or NL Programmer and E1R3 Amplifier.
REFER TO SN-100 FOR
SUGGESTED
GROUNDING METHODS 8
NOTICE
When Fireye products are combined with equipment manufactured by others and/or integrated into sys-
tems designed or manufactured by others, the Fireye warranty, as stated in its General Terms and Condi-
tions of Sale, pertains only to the Fireye products and not to any other equipment or to the combined
system or its overall performance.
WARRANTIES
FIREYE guarantees for one year from the date of installation or 18 months from date of manufacture of
its products to replace, or, at its option, to repair any product or part thereof (except lamps, electronic
tubes and photocells) which is found defective in material or workmanship or which otherwise fails to
conform to the description of the product on the face of its sales order. THE FOREGOING IS IN LIEU
OF ALL OTHER WARRANTIES AND FIREYE MAKES NO WARRANTY OF MERCHANT-
ABILITY OR ANY OTHER WARRANTY, EXPRESS OR IMPLIED. Except as specifically stated
in these general terms and conditions of sale, remedies with respect to any product or part number manu-
factured or sold by Fireye shall be limited exclusively to the right to replacement or repair as above pro-
vided. In no event shall Fireye be liable for consequential or special damages of any nature that may arise
in connection with such product or part.
FIREYE
PFM-14
3 Manchester Road
JUNE 30, 2005
Derry, New Hampshire 03038 USA
Supersedes March 1999
www.fireye.com