See diagram above.
7. Note polarity in terminal block. Attach both
black or white wires to the - side. Attach
both red wires to the + side. Tighten
terminal block screws. See diagram above.
8. Pull wires and LED module into LED
MiniDisc Light barrel until LED module is
flush with top of barrel. Screw on cover
firmly. Tighten strain relief nut firmly.

Very Important! T
o

properly

TighTen

The

black

plasTic

sTrain

relief

nuT
,
firsT

TighTen

firmly

wiTh

your

hand
,
Then

TighTen

an

addiTional

one
-
half

Turn

wiTh

a
7/8"
open

end

wrench
.
9. On the last LED MiniDisc Light in the run,
you will only have one incoming power
wire, no outgoing power wire. On this LED
MiniDisc Light place the incoming power
wire through one hole in the strain relief,
and in the other hole place acrylic rod
included with this instruction sheet.
10. Bring power wire from first LED MiniDisc
Light through a proper strain relief, and
into the LED Driver. Note polarity. Place
black or white power wire into - side,
and red power wire into + side of LED
Driver output.
11. Assure all connections and strain reliefs
are firmly tightened, cover is tight on LED
Driver, and then hard wire LED Driver to
110VAC.
12. LED MiniDisc Light will illuminate in about
3 seconds. If all do not illuminate, check
connections and polarity at the LED Driver.
If one does not illuminate, check connections
and polarity at the unlit LED MiniDisc Light.
13. With system working properly, attach
LED MiniDisc Lights to mounting surface
by securing mounting screws provided
through LED MiniDisc Light cover and
into mounting surface.
Strain Relief
LED Module
Cover
Mounting
Screws
Barrel
Strain Relief
Terminal
Block
2 black or
white wires
2 red
wires
LED Module
Barrel
Gland
side
+ side
s
ide

view
T
op

view
INSTALLATION
Determine where you wish the LED MiniDisc
Light to be placed.
1. Drill a 1.0" diameter hole into mounting
surface. LED MiniDisc Lights will require a
hole of at least 3-1/2" long x 1.0" diameter.
If you wish to recess the cover of the LED
MiniDisc Light for a totally flush mount, you
will need to center drill an additional 2.0"
diameter hole, 5/32" deep. Note that an 18
gauge wire will also have to pass from LED
Driver to all LED MiniDisc Lights.
2. Place LED MiniDisc Lights loosely into holes,
do not mount at this time.
3. Locate LED Driver adjacent to 110VAC.
Remember, 100 LED MiniDisc Lights
maximum per LED Driver. Leave LED Driver
unattached to 110VAC power.
4. Use only 18G wire of the following
specifications:
For all applications with wire interior
to a wall, use only UL listed 18G wire
labeled CL2, NSL part number
LW-18G-CL2.
For all outdoor or burial applications,
use only UL listed 18G wire labeled
Sprinkler Wire or Direct Burial, NSL
part number LW-18G-BUR.
110VAC
LED
DRIVER InstallatIon
InstructIons
LED
M
ini
D
isc
L
ight
WARNING
To reduce the risk of fire, electrical shock, or
injury to persons:
1. Use only with our UL Listed LED Class 2
Driver, LEDDR-12-60W.
2. Parallel wire LED MiniDisc Lights to
LED Driver.
3. Use only 18G wire of the following
specifications:
For all applications with wire interior
to a wall, use only UL listed 18G wire
labeled CL2, NSL part number
LW-18G-CL2.
For all outdoor or burial applications,
use only UL listed 18G wire labeled
Sprinkler Wire or Direct Burial, NSL
part number LW-18G-BUR.
4. First, make sure LED Driver is not receiving
power in any way. Wire LED MiniDisc Lights
per these instructions, assure proper tight-
ness on all terminal blocks, strain reliefs,
and MiniDisc Light covers, and then apply
110VAC power to LED Driver.
5. Do not try to adjust, fix, rewire, LED
module. In the unlikely event LED module
does not illuminate, check wiring polarity
and terminal block first. If this does not
work, send LED module back for warranty
replacement, if applicable.
6. Not for use with dimmers.
notE: These products may represent a possi-
ble shock or fire hazard if improp-
erly installed or attached in any way.
Products should be installed in accor-
dance with the owners manual, current
local codes, and/or the current National
Electrical Code (NEC).
SPECIFICATIONS

Voltage:

UL Listed with our LED
Driver, LEDDR-12-60W

Electrical Rating

Per MiniDisc Light:
0.54 watts, 44mA, 12VDC
Max. MiniDisc Lights

Per Run:
100 MiniDisc Lights per


60 watt LED Driver
Average LED Life:

60,000 hours

Finish Options:

Natural Aluminum, Black,
White, Bronze

Lens:
Frosted

UL Listing:

UL Listed for wet and
burial applications
n
aTional
s
pecialTy
l
ighTing
A
rchitecturAl

And
d
ecorAtive
l
ighting
l
ouisville
, co 80027
www.nslusa.com
© 2006 National Specialty Lighting
APPLICATIONS
Steps
Aisles
Paths
Driveways
Direction Lighting
Information Lighting
Decorative Lighting
Merchandising
Landscape Accents
3
1
/
4
"
2"
1"
Wet, IC and Direct
Burial Locations