for previous versions at the Internet Archive. Yahoo! is not affiliated with the authors of this page or responsible for its content.
TRIPLE OUTPUT AUX SERIES
GENERAL INFORMATION:
The "AUX" Series Accessory provides second and third
adjustable positive HV outputs in addition to the adjustable
main positive high voltage power supply output. The "AUX"
outputs are set for a specific voltage range at the factory.
One output is referred to as the Focus, one as the grid. The
"AUX" is achieved by adding a daughter board inside the
"10A to 35A" high voltage power supply. This "AUX" board
is encapsulated with the main high voltage power supply in
a special taller enclosure to accomadate the height of the
adjust pots. Typical applications are: CRT Raster Display,
X-Y CRT Display, E Beam Bias.
HIGH VOLTAGE "AUX" OUTPUTS :
The "AUX" outputs are non-isolated, positive, unipolar
outputs. Full capability is available over an input range of 12
to 15Vdc ±10% for 4W units and 24 to 28Vdc ±5% for
15W/30W units.The Focus AUX output voltage is fully
functional when the main output is within the range specified
on the ordering information table. The manufactured
tolerance on the output voltage range provided is ±5%.
Line regulation error is < 0.1%, Load regulation error is 0.5V
per uA. The outputs have a temperature co-efficient of
+0.11% per
o
C. Each "AUX" output has a current capability
of 0 to ±25uA, contact factory for higher current. Each
"AUX" output can be adjusted using an internal single turn
potentiometer. The potentiometer adjusts from a factory set
voltage down to 450Vdc lower. Specific outputs available
are:
Standard TC:
Compensated TC:
300V
500V ± 200PPM
450V
650V ± 408PPM
600V
800V ± 537PPM
750V
950V ± 626PPM
900V
1100V ± 690PPM
1050V
The "AUX" Grid HV output is via pin #10 on an addi-
tional pair of standard .025" square IDC pins. These pins
can be used for PCB mounting or direct wiring. The "AUX"
Focus HV output is via an 18" long flying lead.
COMPATIBILITY:
The "AUX" series match the standard "10A to 35A"
series for design methodology, remote control,
enable/disable, reference, shock and vibration. Designed
and built utilizing a state of the art power conversion
topology, these units feature surface mount technology and
encapsulation techniques providing high reliability and
low cost. Base power supply output current rating remains at
full value. Nominal input voltage should be used for
maximum efficiency. Output current monitor is rescaled to
accommodate the "AUX" current.
SHIELDING:
All models are available with optional six-sided
wrap-around Mu-Metal Shielding. This shielding attenuates
magnetic and electrostatic emissions, while shielding ripple
reduction circuitry from outside noise. The high voltage
power supply dimensions change by only 0.010"
PACKAGING:
Since the Auxiliary board is designed to fit inside of the
"10A to 35A" footprint the width and length remain
unchanged. To accommodate the adjust pots all 4w units
are 1.175" ±0.050" high, 15w and 30w units 1.235" ±.050"
high. Standard packaging is our plastic PCB mountable
box. As always, optional six-sided Mu-Metal shielding,
chassis mounting brackets and mounting plates are
available.
ENVIRONMENT:
The AUX Series meets the same environmental
specifications for temperature, shock and vibration as the
10A to 35A series. All units receive a 24-hour burn-in prior
to final test. Extended temperature range is available along
with other enhanced capabilities. Please contact the
factory.
TRIPLE OUTPUT AUX SERIES
HIGH VOLTAGE POWER SUPPLY
Adds Focus and Grid Outputs
Encapsulated within "10Ato 35A" Series
Adjustable Regulated Outputs
Creates a 6.5 in
3
Triple Output Supply
Fixed frequency low stored energy design
High Power Density
Output Short Circuit Protected CS 9002
RONKONKOMA, NY 11779
800-9HV-POWER
FAX 631-471-4696
www.ultravolt.com
Making High Voltage Easier
TRIPLE OUTPUT AUX SERIES
HIGH VOLTAGE POWER SUPPLY
Making High Voltage Easier
CS 9002, Ronkonkoma, NY 11779-9002 Copyright 1991-2000 UltraVolt, Inc.
Type:
0 to 10.7kVDC Main Output (Focus AUX Operational 8kV to 10.7kV)
10AUX
0 to 16.1kVDC Main Output (Focus AUX Operational 11kV to 16.1kV)
15AUX
0 to 21.5kVDC Main Output (Focus AUX Operational 16kV to 21.5kV)
20AUX
0 to 26.8kVDC Main Output (Focus AUX Operational 21.5kV to 26.8kV)
25AUX
0 to 32.2kVDC Main Output (Focus AUX Operational 26.8kV to 32.2kV)
30AUX
0 to 37.6kVDC Main Output (Focus AUX Operational 28.2kV to 37.6kV)
35AUX
Focus Output:
See Table on Pg. 1
-Fvvv
Grid Output:
See Table on Pg. 1
-Gvvv
Temperature Compensated AUX
-TC
Power:
Watts Output (12V Only)
4
Watts Output (24V Only)
20
Watts Output (24V Only)
30
Ordering Information
1 - Input Power Ground Return
2 - Positive Power Input
3 - Iout Monitor
4 - Enable/Disable
5 - Signal Ground Return
6 - Remote Adjust Input
7 - +5V Reference Output
8 - HV Ground Return
9 - Eout Monitor
10 - AUX Grid HV Output
11 - Spare
All grounds joined internally.
Power supply mounting points
isolated from internal grounds by
>100k
, .
01uF / 50V (Max) on all
models except -M, -C and -M-E
configurations which are 0
.
Connections
Example:
15AUX4-F1200-G450-M
Rev. E 7/00
CONSTRUCTION:
Epoxy Filled DAP Box
Chem Film per MIL-M-14F
SDG-F
TOLERANCE:
Overall ±0.050
Pin to Pin ±0.015
#2-56 Standoffs may not be flush to cover
NOTE:
20 & 30 Watt versions are an
additional 0.062 in Height
Contact UV Customer Service for
Drawings on models eqquipped with
-E , -C, or -H options.
PLASTIC CASE
Case:
Plastic Case - Diallyl Phthalate
STD
Earred Heatsink Plate (Pastic Case)
-E
Heatsink:
.400 high (sized to fit case)
-H
Shield:
Six-Sided Mu-Metal Shield
-M
Wire Options:
Anode Flying Lead Terminated with Connector
-ATxx
Anode Flying Lead Shielded
-AS
Option (Case)
Grid Output Voltage
Focus Output Voltage
Anode Flying Lead Protected
-AP
Focus Flying Lead Terminated with Connector
-FTxx
Voltage
Model
Main Output Power