............................................. 4
1.1
Conventions used in this Document .......................................................................... 4
1.2 Checklist.................................................................................................................. 4
1.3 Features ................................................................................................................... 5
2
BOARD LAYOUT ................................................................................................ 6
3
BOARD COMPONENTS ...................................................................................... 7
3.1 Power
Connector...................................................................................................... 7
3.2 Power
LED .............................................................................................................. 7
3.3 Output
LEDs ............................................................................................................ 8
3.4 DIP
Switches ........................................................................................................... 8
3.5 Reset
Button ............................................................................................................ 8
3.6 Prototype
Area ......................................................................................................... 8
3.7 RCM
Jumper ............................................................................................................ 9
3.8 10/100Mbps
Ethernet
Interface............................................................................... 10
3.9 Serial
Interface
COM1 ........................................................................................... 10
4
CONNECTIONS ............................................................................................... 11
4.1 Mounting
the
DNP/5280......................................................................................... 11
4.2 Cable
Connections ................................................................................................. 12
4.3 Serial
Link ............................................................................................................. 13
4.4 Ethernet
Link ......................................................................................................... 14
4.5 Power
Supply......................................................................................................... 15
5
FIRST STEPS ................................................................................................... 16
5.1 Using
a
Windowsbased
development
System ........................................................ 16
5.1.1
Setup the Serial Link .................................................................................................... 16
5.1.2
Checking the Ethernet Link .......................................................................................... 20
5.1.3
Web Server Access....................................................................................................... 21
5.1.4
Assigning a new IP-Address to the DNP/5280 ............................................................... 22
5.1.5
Running Linux ............................................................................................................. 24
5.1.6
File Transfer via TFTP ................................................................................................. 26
5.2
Using a Linuxbased development System ............................................................. 28
5.2.1
Setup the Serial Link .................................................................................................... 28
5.2.2
Checking the Ethernet Link ......................................................................................... 30
5.2.3
Web Server Access....................................................................................................... 31
5.2.4
Assigning a new IP-Address to the DNP/5280 ............................................................... 32
5.2.5
Running Linux ............................................................................................................. 34
5.2.6
File Transfer via TFTP ................................................................................................. 36
5.2.7
GNU Cross Tool Chain................................................................................................. 38
5.2.8
GNU Cross Debugger ................................................................................................... 41
5.2.9
GNU Cross Debugger with DDD (Data Display Debugger) ........................................... 44
6
APPENDIX........................................................................................................ 48
Appendix 1: The DNP/5280 in Detail ................................................................................ 48
A1.1
Block Diagram ............................................................................................................. 48
A1.2
Pin Assignment 64-pin DIL Connector (1. Part) ......................................................... 49
A1.3
Pin Assignment 64-pin DIL Connector (2. Part) ......................................................... 50 DNP/5280 Starter Kit 1 Introduction
SSV EMBEDDED SYSTEMS
3
A1.4
DNP/5280 Function Multiplexing with 64-pin DIL Connector ....................................... 51
A1.5
DNP/5280 LEDs .......................................................................................................... 51
A1.6
BDM-Interface ............................................................................................................. 52
A1.7
PIO-Mapping ............................................................................................................... 53
A1.8
DNP/5280 Expansion Bus Mapping .............................................................................. 54
A1.9 DNP/5280
Memory
Mapping ........................................................................................ 55
Appendix 2: Pin Assignment DNP/EVA2-SV6 Components .............................................. 56
A2.1
COM1 Connector ......................................................................................................... 56
A2.2
10/100 Mbps Ethernet Connector .................................................................................. 56
A2.3 Power
Connector .......................................................................................................... 56
Appendix 3: Connecting an external battery to the DNP/5280 ............................................ 57
Appendix 4: Mechanical Dimensions................................................................................. 58
Appendix 5: GNU General Public License ......................................................................... 59
Appendix 6: GNU Lesser General Public License .............................................................. 64
List of Figures .................................................................................................................. 70
List of Tables.................................................................................................................... 71
List of Appendixes............................................................................................................ 71
Contact ............................................................................................................................. 72
Document History ............................................................................................................. 72 DNP/5280 Starter Kit 1 Introduction
SSV EMBEDDED SYSTEMS
4
1 Introduction
Thank you for choosing an SSV Starter Kit. We are confident that you will be
pleased with the performance of your product. Please take a few minutes to read
this manual. It describes how to start with the DNP/SK13 Starter Kit and will help
you to get out the most of your new system.
For further information about the individual components of this Starter Kit you
may follow the links from our website at: http://www.dilnetpc.com
Our Website contains a lot of technical information, which will be updated in
regular periods.
For specific technical information like hardware description etc. please check
out the Starter Kit CD-ROM, which is an important part of every Starter Kit.
1.1
Conventions used in this Document
Convention Usage
italic
Filenames, Internet addresses like e.g. www.ssv-embedded.de
bold italic
User inputs, command lines and pathnames
bold
New terms
monospace
Program code
E
Keyboard button
Table 1-1: Convention usage
1.2 Checklist
Compare the content of your Starter Kit package with the checklist below. If any
item is missing or appears to be damaged, please contact SSV Embedded Systems.
Standard Items
Evaluation Board DNP/EVA2-SV6
DIL/NetPC DNP/5280
Null-Modem cable
Power Supply
Power Cable
User Manual
Support CD-ROM DNP/5280 Starter Kit 1 Introduction
SSV EMBEDDED SYSTEMS
5
1.3 Features
Evaluation Board DNP/EVA2-SV6
64-pin DIL socket for one DIL/NetPC DNP/5280
One Serial Interface, 1 x RS232
10/100Mbps Ethernet Interface
Eight User-Definable LEDs
Eight Manual DIP Switches
One Reset Switch
Prototype-Area
5 VDC Power Input Connector
Size 140 x 120 mm
DIL/NetPC DNP/5280
Motorola 32-bit MCF5280 ColdFire with 66 MHz Clock Speed
63 MIPS (Dhrystone 2.1)
16 MByte SDRAM Memory, 8 MByte FLASH Memory
10/100 Mbps Ethernet LAN Interface
Four LAN Status LEDs
Two asynchronous Serial Ports (one with all Handshakes)
One I2C Interchip Bus Interface
One Queued Serial Peripheral Interface (SPI)
One CAN Interf