or responsible for its content.
Data Sheet Polymer Products Company Inc.
100 Station Avenue
Stockertown, PA 18083
Customer Service: 1-800-836-8589
Facsimile: 610-759-3692
http:/www.polymerproductscompany.com

*Important: The descriptions, designs, and data contained herein are presented for your information only. Because there are many factors under your control which may affect processing or applications/use it is
necessary for you to make appropriate tests to determine whether the product is suitable for your particular purpose prior to use. NO WARRANTIES OF ANY KIND, EITHER EXPRESS OR IMPLIED, INCLUDING
WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, ARE MADE REGARDING PRODUCTS DESCRIBED OR DESIGNS, OR INFORMATION SET FORTH, OR THAT THE
Data Sheet






FSPP-211



Flame Retardant Polypropylene

FSPP-211 is a highly loaded ready-to-use polypropylene compound designed primarily for injection molding
applications which are required to meet the UL-94 standard of V-0 and the UL-746B long-term performance standard
of 105�C at 0.058 inches in all colors.
Similar in flame-retardant characteristics to FSPP-201, FSPP-211 offers an alternative in physical properties; with
higher impact strength and greater flexibility. In addition, it offers both good molding characteristics and long-term
performance.
Typical Properties*
Test method
ASTM
Unit
Value
Mechanical properties
Tensile Strength at Yield
ASTM D-638
psi
2450
Tensile Elongation
ASTM D-638
%
15
Flexural Modulus
ASTM D-790
psi
280,000
Flexural Strength
ASTM D-790
psi
4,750
Izod Notched Impact Strength
ASTM D-256
ft-lbs/in
0.8
Thermal properties
Vicat Softening Temperature
ASTM D-1525
�F
286
Heat Distortion Temperature, 264 psi
ASTM D-648
�F
130
Processing
Nominal Melt Flow Rate
ASTM D-1238 L
g/10 min
4
Flammability
UL 94 0.058 in.
UL 94
class
V-0
Miscellaneous properties
Density
ASTM D-792
g/cm�
1.37
Mold Shrinkage
ASTM D 955
In/in
0.01
Hardness
ASTM D-2240
77
Oxygen index, %O
2
@ 0.125 in
ASTM-D-2863
28
Properties
English
Flame Retardant and Electrical Data for FSPP-211
Test Method
Test
@ 0.058 in.
@ 0.125 in.
High-Current Arc Resistance
UL-746
Arcs to Ignite
On Surface
No Ignition
No Ignition
1/16 in. above surfac
No Ignition
No Ignition
1/4 in. above surface
No Ignition
No Ignition
Hot Wire Ignition
UL-746
Seconds to ignite
No Ignition
No Ignition
Arc Resistance
ASTM-D-495
Seconds to track
--
76
Arc Tracking Ratio
UL-746
Inches per minute
0
0
High-Voltage Arc Resistance
UL-746
Seconds to track
No track
No track
Seconds to ignite
No ignition
No ignition
Dielectric Strength, volts/mil
ASTM-D-149
Normal/Moist
>823 / 814
--
Volume Resistivity, Megohm-cm
ASTM-D-257
Normal/moist
1.79/26.4 E10
--
Continuous Track Index, Volts
--
>500
Dielectric Constant @ 1 MHz
ASTM-D-150
--
2.64
Dissipation Factor @ 1 MHz
ASTM-D-150
--
0.00265
Continuous Operating Temperature, �C
UL-746B
105
--
Properties
Value

PRODUCTS, DESIGNS, OR DATA MAY BE USED WITHOUT INFRINGING THE INTELLECTUAL PROPERTY RIGHTS OF OTHERS. IN NO CASE SHALL THE DESCRIPTIONS, DATA OR DESIGNS
PROVIDED BE PRESUMED TO BE A PART OF OUR TERMS AND CONDITIONS OF SALE. Further, you expressly understand and agree that the descriptions, designs, and data furnished by Polymer Products
hereunder are given gratis and Polymer Products assumes no obligation or liability for same or results obtained from use thereof, all such being given to you and accepted by you at your risk. Any laboratory
flammability tests set forth herein are not intended to reflect hazards prescribed by materials under actual fire conditions. As governmental regulations and use conditions may change, it is the Buyer's responsibility
to determine the suitability of Polymer Product's products for specific applications.

TDS-020 Rev. 1
3/31/05
Polymer Products Company Inc.
100 Station Avenue
Stockertown, PA 18083
Customer Service: 1-800-836-8589
Facsimile: 610-759-3692
http:/www.polymerproductscompany.com

*Important: The descriptions, designs, and data contained herein are presented for your information only. Because there are many factors under your control which may affect processing or applications/use it is
necessary for you to make appropriate tests to determine whether the product is suitable for your particular purpose prior to use. NO WARRANTIES OF ANY KIND, EITHER EXPRESS OR IMPLIED, INCLUDING
WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, ARE MADE REGARDING PRODUCTS DESCRIBED OR DESIGNS, OR INFORMATION SET FORTH, OR THAT THE
Data Sheet
Handling and Use
FSPP-211 is a flame-retardant polypropylene compound that is to be used as received. No special precautions or
conditions are required. It is recommended, however, that FSPP-211 not be held for long periods of time in the molten
state as decomposition could occur. Machines should be purged prior to shutdown.
PPC flame retardant compounds and concentrates are considered to be non-hazardous under normal conditions.
Material Safety Data Sheets are available on all these products, and you are encouraged to read and understand
these documents before using the product. Since these products are used at elevated temperatures, fumes may be
generated under some use conditions. Ventilation is necessary to minimize employee exposure to these fumes.
Packaging and Samples
Standard packaging for concentrates is in 1,000-lb boxes, lined and on pallets. Optional are 250-lb fiber drums and
50-lb bags. To meet particular needs, boxes up to 1,400 lb can be supplied. Samples are available on request.


PRODUCTS, DESIGNS, OR DATA MAY BE USED WITHOUT INFRINGING THE INTELLECTUAL PROPERTY RIGHTS OF OTHERS. IN NO CASE SHALL THE DESCRIPTIONS, DATA OR DESIGNS
PROVIDED BE PRESUMED TO BE A PART OF OUR TERMS AND CONDITIONS OF SALE. Further, you expressly understand and agree that the descriptions, designs, and data furnished by Polymer Products
hereunder are given gratis and Polymer Products assumes no obligation or liability for same or results obtained from use thereof, all such being given to you and accepted by you at your risk. Any laboratory
flammability tests set forth herein are not intended to reflect hazards prescribed by materials under actual fire conditions. As governmental regulations and use conditions may change, it is the Buyer's responsibility
to determine the suitability of Polymer Product's products for specific applications.

TDS-020 Rev. 1
3/31/05