page taken as our search engine crawled the Web.
The web site itself may have changed. You can check the current page or check for previous versions at the Internet Archive. Yahoo! is not affiliated with the authors of this page or responsible for its content.
High Bandwidth, Analog/Video Optocouplers Technical Data High Bandwidth, Analog/Video
Optocouplers
Technical Data
Features
Wide Bandwidth
[1]
:
17 MHz (HCPL-4562)
9 MHz (HCNW4562)
High Voltage Gain
[1]
:
2.0 (HCPL-4562)
3.0 (HCNW4562)
Low G
V
Temperature
Coefficient: -0.3%/
°
C
Highly Linear at Low Drive
Currents
High-Speed AlGaAs Emitter
Safety Approval
UL Recognized - 2500 V rms
for 1 minute (5000 V rms for
1 minute for HCPL-
4562#020 and HCNW4562)
per UL 1577
CSA Approved
VDE 0884 Approved
-V
IORM
= 1414 V
peak
for
HCNW4562
Available in 8-Pin DIP and
Widebody Packages
Applications
Video Isolation for the
Following Standards/
Formats: NTSC, PAL,
SECAM, S-VHS, ANALOG
RGB
Low Drive Current Feedback
Element in Switching Power
Supplies, e.g., for ISDN
Networks
A/D Converter Signal
Isolation
Analog Signal Ground
Isolation
High Voltage Insulation
Description
The HCPL-4562 and HCNW4562
optocouplers provide wide band-
width isolation for analog signals.
They are ideal for video isolation
when combined with their
application circuit (Figure 4).
High linearity and low phase shift
are achieved through an AlGaAs
LED combined with a high speed
detector. These single channel
optocouplers are available in
8-Pin DIP and Widebody package
configurations.
HCPL-4562
HCNW4562
CAUTION: It is advised that normal static precautions be taken in handling and assembly of this component to
prevent damage and/or degradation which may be induced by ESD.
Functional Diagram
7
1
2
3
4
5
6
8
NC
ANODE
CATHODE
NC
VCC
VB
VO
GND 2
Selection Guide
Single Channel Packages
8-Pin DIP
Widebody
(300 Mil)
(400 Mil)
HCPL-4562
HCNW4562
Ordering Information
Specify Part Number followed by Option Number (if desired).
Example:
HCPL-4562#XXX
020 = UL 5000 V rms/1 Minute Option*
300 = Gull Wing Surface Mount Option
500 = Tape and Reel Packaging Option
Option data sheets are available. Contact your Agilent sales representative or authorized distributor for
information.
*For HCPL-4562 only.
Gull wing surface mount option applies to through hole parts only.
Schematic
IF
8
6
5 GND
VCC
2
3
VO
ICC
VF
IO
ANODE
CATHODE
+ 7
VB
IB 3
Package Outline Drawings
8-Pin DIP Package (HCPL-4562)
8-Pin DIP Package with Gull Wing Surface Mount Option 300 (HCPL-4562)
0.635 ± 0.25
(0.025 ± 0.010)
12° NOM.
9.65 ± 0.25
(0.380 ± 0.010)
0.635 ± 0.130
(0.025 ± 0.005)
7.62 ± 0.25
(0.300 ± 0.010)
5
6
7
8
4
3
2
1
9.65 ± 0.25
(0.380 ± 0.010)
6.350 ± 0.25
(0.250 ± 0.010)
1.016 (0.040)
1.194 (0.047)
1.194 (0.047)
1.778 (0.070)
9.398 (0.370)
9.906 (0.390)
4.826
(0.190)TYP.
0.381 (0.015)
0.635 (0.025)
PAD LOCATION (FOR REFERENCE ONLY)
1.080 ± 0.320
(0.043 ± 0.013)
4.19
(0.165)MAX.
1.780
(0.070)
MAX.
1.19
(0.047)
MAX.
2.54
(0.100)
BSC
DIMENSIONS IN MILLIMETERS (INCHES).
LEAD COPLANARITY = 0.10 mm (0.004 INCHES).
0.254 + 0.076
- 0.051
(0.010+ 0.003)
- 0.002)
5
6
7
8
4
3
2
1
11.15 ± 0.15
(0.442 ± 0.006)
1.78 ± 0.15
(0.070 ± 0.006)
5.10
(0.201)MAX.
1.55
(0.061)
MAX.
2.54 (0.100)
TYP.
DIMENSIONS IN MILLIMETERS (INCHES).
7° TYP.
0.254 + 0.076
- 0.0051
(0.010+ 0.003)
- 0.002)
11.00
(0.433)
9.00 ± 0.15
(0.354 ± 0.006)
MAX.
10.16 (0.400)
TYP.
A
HCNWXXXX
YYWW
DATE CODE
TYPE NUMBER
0.51 (0.021) MIN.
0.40 (0.016)
0.56 (0.022)
3.10 (0.122)
3.90 (0.154) 4
8-Pin Widebody DIP Package (HCNW4562)
8-Pin Widebody DIP Package with Gull Wing Surface Mount Option 300 (HCNW4562)
1.00 ± 0.15
(0.039 ± 0.006)
7° NOM.
12.30 ± 0.30
(0.484 ± 0.012)
0.75 ± 0.25
(0.030 ± 0.010)
11.00
(0.433)
5
6
7
8
4
3
2
1
11.15 ± 0.15
(0.442 ± 0.006)
9.00 ± 0.15
(0.354 ± 0.006)
1.3
(0.051)
12.30 ± 0.30
(0.484 ± 0.012)
6.15
(0.242)TYP.
0.9
(0.035)
PAD LOCATION (FOR REFERENCE ONLY)
1.78 ± 0.15
(0.070 ± 0.006)
4.00
(0.158)MAX.
1.55
(0.061)
MAX.
2.54
(0.100)
BSC
DIMENSIONS IN MILLIMETERS (INCHES).
LEAD COPLANARITY = 0.10 mm (0.004 INCHES).
0.254 + 0.076
- 0.0051
(0.010+ 0.003)
- 0.002)
MAX.
5
6
7
8
4
3
2
1
11.15 ± 0.15
(0.442 ± 0.006)
1.78 ± 0.15
(0.070 ± 0.006)
5.10
(0.201)MAX.
1.55
(0.061)
MAX.
2.54 (0.100)
TYP.
DIMENSIONS IN MILLIMETERS (INCHES).
7° TYP.
0.254 + 0.076
- 0.0051
(0.010+ 0.003)
- 0.002)
11.00
(0.433)
9.00 ± 0.15
(0.354 ± 0.006)
MAX.
10.16 (0.400)
TYP.
Agilent
HCNWXXXX
YYWW
DATE CODE
TYPE NUMBER
0.51 (0.021) MIN.
0.40 (0.016)
0.56 (0.022)
3.10 (0.122)
3.90 (0.154) 5
Note: Use of nonchlorine activated fluxes is highly recommended.
240 T = 115°C, 0.3°C/SEC
0 T = 100°C, 1.5°C/SEC T = 145°C, 1°C/SEC
TIME MINUTES
TEMPERATURE °C
220
200
180
160
140
120
100
80
60
40
20
0
260
1
2
3
4
5
6
7
8
9
10
11
12
Solder Reflow Temperature Profile (Gull Wing Surface Mount Option Parts)
Regulatory Information
The devices contained in this data
sheet have been approved by the
following organizations:
UL
Recognized under UL 1577,
Component Recognition
Program, File E55361.
CSA
Approved under CSA Component
Acceptance Notice #5, File CA
88324.
VDE
Approved according to VDE
0884/06.92 (HCNW4562 only).
Insulation and Safety Related Specifications
8-Pin DIP
Widebody
(300 Mil)
(400 Mil)
Parameter
Symbol
Value
Value
Units
Conditions
Minimum External
L(101)
7.1
9.6
mm
Measured from input terminals to
Air Gap (External
output terminals, shortest distance
Clearance)
through air.
Minimum External
L(102)
7.4
10.0
mm
Measured from input terminals to
Tracking (External
output terminals, shortest distance
Creepage)
path along body.
Minimum Internal
0.08
1.0
mm
Through insulation distance,
Plastic Gap
conductor to conductor, usually the
(Internal Clearance)
direct distance between the photo-
emitter and photodetector inside the
optocoupler cavity.
Minimum Internal
NA
4.0
mm
Measured from input terminals to
Tracking (Internal
output terminals, along internal cavity.
Creepage)
Tracking Resistance
CTI
200
200
Volts
DIN IEC 112/VDE 0303 Part 1
(Comparative
Tracking Index)
Isolation Group
IIIa
IIIa
Material Group
(DIN VDE 0110, 1/89, Table 1)
Option 300 - surface mount classification is Class A in accordance with CECC 00802. 6
VDE 0884 Insulation Related Characteristics (HCNW4562 ONLY)
Description
Symbol
Characteristic
Units
Installation classification per DIN VDE 0110/1.89, Table 1
for rated mains voltage 600 V rms
I-IV
for rated mains voltage 1000 V rms
I-III
Climatic Classification
55/85/21
Pollution Degree (DIN VDE 0110/1.89)
2
Maximum Working Insulation Voltage
V
IORM
1414
V
peak
Input to Output Test Voltage, Method b*
V
IORM
x 1.875 = V
PR
, 100% Production Test with t
m
= 1 sec,
V
PR
2652
V
peak
Partial Discharge < 5 pC
Input to Output Test Voltage, Method a*
V
IORM
x 1.5 = V
PR
, Type and sample test,
V
PR
2121
V
peak
t
m
= 60 sec, Partial Discharge < 5 pC
Highest Allowable Overvoltage*
(Transient Overvoltage, t
ini
= 10 sec)
V
IOTM
8000
V
peak
Safety Limiting Values
(Maximum values allowed in the event of a failure,
also see Figure 17, Thermal Derating curve.)
Case Temperature
T
S
150
°
C
Input Current
I
S,INPUT
400
mA
Output Power
P
S,OUTPUT
700
mW
Insulation Resistance at T
S
, V
IO
= 500 V
R
S 10
9 *Refer to the front of the optocoupler section of the current catalog, under Product Safety Regulations section (VDE 0884), for a
detailed description.
Note: Isolation characteristics are guaranteed only within the safety maximum ratings which must be ensured by protective circuits in
application. 7
Absolute Maximum Ratings
Parameter
Symbol
Device
Min.
Max.
Units
Note
Storage Temperature
T
S
-55
125
°
C
Operating Temperature
T
A
-40
85
°
C
Average Forward Input Current
I
F(avg)
HCPL-4562
12
mA
HCNW4562
25
Peak Forward Input Current
I
F(PEAK)
HCPL-4562
18.6
mA
HCNW4562
40
Effective Input Current
I
F(EFF)
HCPL-4562
12.9
mA rms
Reverse LED Input Voltage (Pin 3-2)
V
R
HCPL-4562
1.8
V
HCNW4562
3
Input Power Dissipation
P
IN
HCNW4562
40
mW
Average Output Current (Pin 6)
I
O(AVG)
8
mA
Peak Output Current (Pin 6)
I
O(PEAK)
16
mA
Emitter-Base Reverse Voltage (Pin 5-7)
V
EBR
5
V
Supply Voltage (Pin 8-5)
V
CC
-0.3
30
V
Output Voltage (Pin 6-5)
V
O
-0.3
20
V
Base Current (Pin 7)
I
B
5
mA
Output Power Dissipation
P
O
100
mW
2
Lead Solder Temperature
T
LS
HCPL-4562
260
°
C
HCNW4562
260
°
C
Reflow Temperature Profile
T
RP
Option
300
Drawings Section
1.6 mm Below Seating Plane, 10 Seconds
up to Seating Plane, 10 Seconds
Recommended Operating Conditions
Parameter
Symbol
Device
Min.
Max.
Units
Note
Operating Temperature
T
A
HCPL-4562
-10
70
°
C
Quiescent Input Current
I
FQ
HCPL-4562
6
mA
HCNW4562
10
Peak Input Current
I
F(PEAK)
HCPL-4562
10
mA
HCNW4562
17
See Package Outline 8
Electrical Specifications (DC)
T
A
= 25
°
C, I
F
= 6 mA for HCPL-4562 and I
F
= 10 mA for HCNW4562 (i.e., Recommended I
FQ
) unless
otherwise specified.
Parameter
Symbol
Device
Min. Typ.* Max. Units
Test Conditions
Fig. Note
Base Photo
I
PB
13
31
65
µ
A
I
F
= 10 mA
V
PB
5 V
2, 6
Current
HCPL-4562
19.2
I
F
= 6 mA
I
PB I
PB
/
-0.3
%/
°
C
2 mA < I
F
< 10 mA,
2
Temperature T
V
PB
5 V
Coe