UPON IN WRITING. 8 COPYRIGHT 2006 EDI.
REVISION: NOVEMBER 2006
pn 888-2018-001


2018KCL Series
18 Channel RMS Signal Monitor with Datakey

Operations Manual
TM
TM


<blank>





MAINTENANCE NOTE

EBERLE DESIGN INC. SIGNAL MONITORS HAVE BEEN CAREFULLY INSPECTED AND TESTED TO
ENSURE PROPER OPERATION. IT IS RECOMMENDED THAT THE SIGNAL MONITOR BE TESTED AT
LEAST ANNUALLY TO ENSURE COMPLIANCE WITH THE PROPER SPECIFICATIONS.





SECTION 4.1.2, SPECIAL FUNCTION INPUTS

SPECIAL FUNCTION #2 HAS BEEN DISABLED TO PROVIDE COMPATIBILITY WITH THE MT-180
MONITOR TESTER. RESISTOR R31 HAS BEEN REMOVED TO DISABLE THIS CIRCUIT. IF SPECIAL
FUNCTION #2 INPUT IS REQUIRED, R31 (150K OHMS, 1/2W) SHOULD BE INSTALLED.








- WARNING -
THE P1 RED INTERFACE CABLE SHOULD ALWAYS BE UNPLUGGED BEFORE
REMOVING THE UNIT FROM THE CABINET TO PREVENT POTENTIAL EXPOSURE
TO ELECTRICAL SHOCK.




<blank>
TABLE OF CONTENTS

Section 1 BASIC FUNCTIONS...................................................................................................................... 1

1.1

Model Description................................................................................................................ 1

1.2

Basic Functions................................................................................................................... 1

1.2.1 Datakey Parameter Programming.............................................................................. 1

1.2.2 Conflict Monitoring...................................................................................................... 2

1.2.3 24VDC Monitoring (VDC)........................................................................................... 2

1.2.4 Controller Watchdog Monitoring (WDT) ..................................................................... 2

Section 2 EXTENDED FEATURES .............................................................................................................. 3

2.1

Hardware Features.............................................................................................................. 3

2.2

Red Failure Monitoring ........................................................................................................ 3

2.2.1 Red Interface Cable Fault .......................................................................................... 3

2.3

GYR-Dual Indication Monitoring.......................................................................................... 4

2.4

Clearance (Short or Absent Yellow) Monitoring .................................................................. 4

2.4.1 Minimum Yellow Change Interval............................................................................... 4

2.4.2 Minimum Yellow Plus Red Interval............................................................................. 4

2.5

AC Line Brown-out Detection.............................................................................................. 4

2.5.1 Minimum Flash Time .................................................................................................. 5

2.6

LEDguard
TM
LED Field Signal Sensing............................................................................... 5

2.7

Recurrent Pulse Detection .................................................................................................. 5

2.8

Exit Flash............................................................................................................................. 6

2.9

Non-Volatile Fault Memory.................................................................................................. 6

2.10

KEY (Datakey Absent) Indication........................................................................................ 6

2.10.1 Datakey Memory Diagnostic .................................................................................... 6

2.11

Configuration Change Monitoring........................................................................................ 6

2.12

Internal MPU Watchdog ...................................................................................................... 6

2.13

Reset Input Detection..........................................................................................................7

2.14

LED Test ............................................................................................................................. 7

2.15

Memory Test ....................................................................................................................... 7

2.16

Watchdog Monitoring Disabled Indicator ............................................................................ 7

2.17

Red Failure Monitor Disabled IndicatoR ............................................................................. 7

2.18

Diagnostic Display Mode..................................................................................................... 7

2.18.1 No Fault Diagnostic Display ..................................................................................... 7

2.18.2 Fault Diagnostic Display........................................................................................... 7

2.19

Flashing Yellow Arrow (FYA) Overview .............................................................................. 8

2.19.1 FYA Mode ................................................................................................................8

2.19.2 FYAc (Compact) Mode........................................................................................... 10

Section 3 EVENT LOGGING FEATURES .................................................................................................. 12

3.1

Basic Front Panel Fault Event Display.............................................................................. 12

3.2

Status and Event Reporting .............................................................................................. 12

3.2.1 BI Tran Systems 233 Program Monitor Status......................................................... 12

3.2.2 EDI ECcom Monitor Report...................................................................................... 12

3.2.3 EDI ECcom Monitor Event Log Examples ............................................................... 13

3.3

Signal Sequence Event Log.............................................................................................. 15

Section 4 INSTALLATION........................................................................................................................... 16

4.1

Adapting Red Monitoring................................................................................................... 16

4.1.1 Red Field Inputs ....................................................................................................... 16

4.1.2 Special Function Preempt Inputs (SF1,2) ................................................................ 16

4.2

Datakey Parameters.......................................................................................................... 17

4.2.1 Datakey Parameter Programming............................................................................ 17

4.2.2 MonitorKey Configuration Set-up Wizard................................................................. 17

4.2.3 Unit Data Parameters............................................................................................... 17

4.2.4 Permissive Channel Pair Parameters ...................................................................... 18

4.2.5 Red Fail Enable Parameters .................................................................................... 18

4.2.6 Dual Indication Enable Parameters.......................................................................... 18

4.2.7 Clearance Enable Parameters ................................................................................. 18

4.2.8 Yellow Disable Parameters ...................................................................................... 18

4.2.9 Flashing Yellow Arrow (FYA / FYAc) Parameters.................................................... 19
Section 5 FRONT PANEL DESCRIPTION ................................................................................................. 20

5.1

Indicators........................................................................................................................... 20

5.1.1 AC PWR Indicator .................................................................................................... 20

5.1.2 VDC Indicator........................................................................................................... 20

5.1.3 WDT Indicator .......................................................................................................... 20

5.1.4 CONFLICT Indicator................................................................................................. 20

5.1.5 RED FAIL Indicator .................................................................................................. 20

5.1.6 DUAL IND Indicator.................................................................................................. 20

5.1.7 CLEARANCE Indicator ............................................................................................ 20

5.1.8 KEY Indicator ........................................................................................................... 20

5.1.9 DIAGNOSTIC Indicator ............................................................................................ 20

5.1.10 RP DETECT Indicator ........