lor=black> Below is a cache of http://wilsonelectronics.com/Files/AdapterGuide/Guide.pdf. It's a snapshot of the page taken as our search engine crawled the Web.
The web site itself may have changed. You can check the current page or check for previous versions at the Internet Archive. Yahoo! is not affiliated with the authors of this page or responsible for its content.
Antenna Adapter Type Descriptions 1
www.wilsonelectronics.com
Toll Free 1-866-294-6996
W
ilson Electr
onics


T
APS & SPLITTERS



W
ilson Electr
onics
W
ilson Electr
onics


ANTENN
A AD
APTER TYPE DESCRIPTIONS

W
ilson Electr
onics

Wilson Electronics
Antenna Adapter
Type Descriptions
Back Plug
Plugs into the adapter port on the upper
back portion of the phone. A rubber or
plastic plug may need to be removed.
Press firmly to ensure a good connection -
do not twist. Using too much force could
damage the phone.
Back Plug with Replacement Antenna
(1&2) Unscrew the original antenna that is
blocking the adapter port - may have
reversed threads. (3) Screw the included
replacement antenna into the top of the
phone. The antenna adapter will now fit
into the back of the phone - see above for
Back Plug instructions.
Bottom Plug
Plugs into the bottom of the cell phone.
Push until there is a click. Press button(s)
in middle or on sides to release connector
from the phone. Note: an RF charger may
be available for the phone - it will allow
charging of the phone while using the
external antenna.
Cellular Data Cards
Adapter plugs into the adapter port on the
end of the cellular data card or plugs in as
an antenna replacement. Check the model
for a specific adapter type.
Ring
Slide onto the base of the cellular phone's
built in antenna. Press down firmly to
ensure a good connection. Be sure to
lower the phone's built-in antenna.
Sleeve
Snap onto the back of the cellular phone.
The sleeve must be mounted to the top of
the phone. The sleeve may fit upside
down but it will not function properly.
Top Plug
Plugs into the adapter port on the top of
the phone. A rubber plug may need to be
removed. Press firmly to ensure a good
connection - do not twist. Using too much
force could damage the phone.
Top Replacement Antenna
(1) Pry off plastic cap. Depress plastic tab
inside hole while forcefully pulling out the
original antenna. (2) Insert adapter plug into
phone with wires facing phone. (4) Screw
adapter into top of phone. (3) This
replacement antenna is needed after
disconnecting the antenna adapter.
Top Screw
This antenna adapter replaces the cellular
phone's original antenna. Unscrew the
original antenna and screw in the antenna
adapter. Be sure to save the original
antenna - it will be needed after
disconnecting the antenna adapter.
Side Plug
Plugs into the adapter port on the
upper-side of the phone. A rubber plug
may need to be removed. Press firmly to
ensure a good connection - do not twist.
Using too much force could damage the
phone.
Back Replacement
Remove the rubber Nextel cover. Remove
the 2 screws using the included Torx T8 bit.
Attach the new adapter plate using the
provided Phillips screws. Tighten left
screw then the right. When the adapter is
pushed into the back of the phone it should
snap into place.
Back Plate
Place included VELCRO
®
on back top of
phone as shown. Attach adapter to
VELCRO
®
.
Note: Also works with cellular data cards.
Top Ring with Plug
Slide onto the base of the cellular phone's
built in antenna while aligning the plug with
the adapter port. Press down firmly to
ensure a good connection.
TECH SUPPORT
1) Call Toll-Free 866-294-1660
2) E-mail
tech@wilsonelectronics.com
3) Visit
www.wilsonelectronics.com
For more details and the latest information regarding adapters visit
www.wilsonelectronics.com
Adapter and Charger
Guides are Available