mmand creates a specified port. See
Table 27-1 on page 27-1
for
supported modifiers by platform.
Usage Guidelines Support is limited to ports with pluggable port modules (PPMs). When 1GFICON and 2GFICON payloads are provisioned, distance extension=B2B is the default
and only valid setting. Setting distance extension (using ED-1GFICON or ED-2GFICON) to any
other setting will be denied with an SROF (Provisioning Rules Failed) error message.
Category
Ports
Security
Provisioning
Input Format
ENT-<MOD1PAYLOAD>:[<TID>]:<AID>:<CTAG>[::::];
Input Example
ENT-GIGE:TID:FAC-5-1:1;
Input Parameters
<AID>
Access identifier from the
25.13 FACILITY section on page 25-16
. 12-2
Cisco ONS 15454 SDH and Cisco ONS 15600 SDH TL1 Command Guide, R8.0
Chapter 12 ENT Commands
12.2 ENT-<MOD_RING>
12.2 ENT-<MOD_RING>
(Cisco ONS 15454 SDH and ONS 15600 SDH) The Enter MS-SPRing (ENT-<MOD_RING>) command
creates either a two-fiber or four-fiber multiplex section-shared protection ring (MS-SPRing).
Usage Guidelines
The following actions will return error messages: If RINGID is different from the string presented in the AID format, a RingId Does Not Match With
AID (IIAC) error message is returned. Sending this command to create a MS-SPRing with an out-of-range node ID or ring ID will return
an Invalid NodeId (IIAC) or Invalid RingId (IIAC) error message. Sending this command to create a four-fiber MS-SPRing on STM-4 cards, or a two-fiber
MS-SPRing on STM-1 cards will return an Input, Invalid work/prot port (IIAC) error message. Sending this command to create a MS-SPRing on a network element (NE) that already has five
MS-SPRings will return an MSSPR Creation Failed (SRQN) error message because only one NE
can support up to five MS-SPRings. Sending this command to create a MS-SPRing on a port with 1+1 protection will return an SRQN
error message. If the system fails while accessing the Information Object Repository (IOR), a Get IOR Failed
(SROF) error message is returned. If the AID is invalid, an Invalid AID (IIAC) error message is returned. If any facility requested in this command is in use, a Facility is Busy (SPLD) error message is
returned. An invalid creation query will return the SRQN error message. Sending this command to provision the mode with an invalid MS-SPRing mode will return an
Invalid MSSPR Mode (IIDT) error message. Sending this command to modify SRVRTV or SRVTM on the two-fiber MS-SPRing will return an
Invalid Data for 2F-MSSPR (IDNV) error message. Sending this command to provision the node ID with invalid data will return an IIAC error message. Sending this command to provision the ring ID with invalid data will return an IIAC error message. Sending this command with an invalid working AID will return an Invalid MSSPR Working Facility
(IIDT) error message. Sending this command with an invalid protection AID will return an Invalid MSSPR Protect Facility
(IIDT) error message. Changing the MS-SPRing node ID with a duplicated ID will return a Cannot Set NodeId (SROF)
error message.
Note
Both <EASTPROT> and <WESTPROT> are optional, but required for four-fiber MS-SPRing creation.
Note
The ALL AID is invalid for this command. 12-3
Cisco ONS 15454 SDH and Cisco ONS 15600 SDH TL1 Command Guide, R8.0

Chapter 12 ENT Commands
12.2 ENT-<MOD_RING>
Category
MS-SPRing
Security
Provisioning
Input Format
ENT-<MOD_RING>:[<TID>]:<AID>:<CTAG>:::[RINGID=<RINGID>],NODEID=<NODEID>,
MODE=<MODE>,[RVRTV=<RVRTV>],[RVTM=<RVTM>],[SRVRTV=<SRVRTV>],
[SRVTM=<SRVTM>],EASTWORK=<EASTWORK>,WESTWORK=<WESTWORK>,
[EASTPROT=<EASTPROT>,][WESTPROT=<WESTPROT>];
Input Example
Four-fiber MS-SPRing:
ENT-MSSPR:TID:MSSPR-N02ABC:CTAG:::RINGID=N02ABC,NODEID=3,MODE=4F,
RVRTV=Y,RVTM=5.0,SRVRTV=Y,SRVTM=5.0,EASTWORK=FAC-5-1,WESTWORK=FAC-6-1,
EASTPROT=FAC-12-1,WESTPROT=FAC-13-1;
Two-fiber MS-SPRing:
ENT-MSSPR:TID:MSSPR-N04EFG:CTAG:::RINGID=N04EFG,NODEID=6,MODE=2F,RVRTV=Y,
RVTM=5.0,EASTWORK=FAC-5-1,WESTWORK=FAC-6-1;
Input Parameters
<AID>
Access identifier from the
25.3 AidUnionId1 section on page 25-7
. Identifies
the MS-SPRing of the NE. ALL or MSSPR-ALL AIDs are not allowed for
editing MS-SPRing. This command only supports a single MS-SPRing AID.
<RINGID>
(Optional) The MS-SPRing ID of the NE up to six characters. Valid characters
are A-Z and 0-9. RINGID is a string. This parameter defaults to the text in the
AID that follows MSSPR.
<NODEID>
(Optional) The MS-SPRing node ID of the NE. NODEID ranges from 0 to 31.
NODEID is an integer.
<MODE>
(Optional) Mode with which the command is to be implemented. Identifies the
MS-SPRing mode. The parameter type is MSSPR_MODE, which is the
MS-SPRing mode. 2F
Two-fiber MS-SPRing 4F
Four-fiber MS-SPRing
<RVRTV>
(Optional) Revertive mode. The value Y indicates that protection switching
system reverts service to the original line after restoration. The value N
indicates that protection switching system does not revert service to the original
line after restoration. RVRTV is applicable only for 1+1 protection switching.
Null defaults to N. The parameter type is ON_OFF (disable or enable an
attribute). N
Does not revert service to original line after restoration. Y
Reverts service to original line after restoration.
<RVTM>
(Optional) Revertive time. Defaults to 5.0. The parameter type is
REVERTIVE_TIME (revertive time). 0.5 to 12.0
Revertive time is 0.5 to 12.0 minutes. 12-4
Cisco ONS 15454 SDH and Cisco ONS 15600 SDH TL1 Command Guide, R8.0
Chapter 12 ENT Commands
12.3 ENT-BULKROLL-<STM_TYPE>
12.3 ENT-BULKROLL-<STM_TYPE>
(Cisco ONS 15454 SDH and ONS 15600 SDH) The Enter Bulkroll for STM-4, STM-64, STM-1, or
STM-16 (ENT-BULKROLL-<STM_TYPE>) command enters information about rolling traffic from one
endpoint to another without interrupting service. This command supports line-level rolling and bulk
rolling and cannot be used for single-path-level rolling. See
Table 27-1 on page 27-1
for supported
modifiers by platform.
Usage Guidelines
None
Category
Bridge and Roll
Security
Provisioning
Input Format
ENT-BULKROLL-<STM_TYPE>:[<TID>]:<FROM>:<CTAG>:::RTOSTART=<RTOSTART>,
[RFROMSTART=<RFROMSTART>],[RFROMEND=<RFROMEND>],[RMODE=<RMODE>],
[CMDMDE=<CMDMDE>];
Input Example
ENT-BULKROLL-STM-64:CISCO:FAC-2-1:123:::RTOSTART=VC3-3-1-1,RFROMSTART=VC3-2-1-1,
RFROMEND=VC3-3-1-1,RMODE=AUTO,CMDMDE=FRCD;
<SRVRTV>
(Optional) The span revertive mode for four-fiber MS-SPRing only. Defaults to
Y. The parameter type is ON_OFF (disable or enable an attribute). N
Disable an attribute. Y
Enable an attribute.
<SRVTM>
(Optional) The span revertive time for four-fiber MS-SPRing only. Defaults to
5.0. The parameter type is REVERTIVE_TIME (revertive time). 0.5 to 12.0
Revertive time is 0.5 to 12.0 minutes.
<EASTWORK>
(Optional) East working facility. AID from the
25.13 FACILITY section on
page 25-16
.
<WESTWORK>
(Optional) West working facility. AID from the
25.13 FACILITY section on
page 25-16
.
<EASTPROT>
(Optional) East protecting facility. AID from the
25.13 FACILITY section
on page 25-16
.
<WESTPROT>
(Optional) West protecting facility. AID from the
25.13 FACILITY section
on page 25-16
. 12-5
Cisco ONS 15454 SDH and Cisco ONS 15600 SDH TL1 Command Guide, R8.0

Chapter 12 ENT Commands
12.3 ENT-BULKROLL-<STM_TYPE>
Input Parameters
<FROM>
One of the endpoints. Access identifier from the
25.13 FACILITY section
on page 25-16
for line-level rolling and bulk rolling.
<RTOSTART>
The starting time slot in the destination roll port. For bulk rolling only. The
parameter type is PATH, which is the modifier for path commands. VC3
Synchronous Transport Signal/Module Level-1 (51 Mbps) VC44C
Synchronous Transport Signal/Module Level-12 Concatenated (622 Mbps) VC464C
Synchronous Transport Signal/Module Level-192 Concatenated (9952 Mbps) VC48C
Synchronous Transport Signal/Module Level-24 Concatenated (1240 Mbps) VC4
Synchronous Transport Signal/Module Signal Level-3 Concatenated
(155 Mbps) VC416C
Synchronous Transport Signal/Module Level-48 Concatenated (2488 Mbps) VC42C
Synchronous Transport Signal/Module level-6 (310 Mbps) VC43C
Synchronous Transport Signal/Module Level-9 Concatenated (465 Mbps) VC11
Virtual Channel 11 VC12
Virtual Channel 12
<RFROMSTART>
(Optional) The starting time slot in the source roll port. For bulk rolling only.
The parameter type is PATH, which is the modifier for path commands. VC3
Synchronous Transport Signal/Module Level-1 (51 Mbps) VC44C
Synchronous Transport Signal/Module Level-12 Concatenated (622 Mbps) VC464C
Synchronous Transport Signal/Module Level-192 Concatenated (9952 Mbps) VC48C
Synchronous Transport Signal/Module Level-24 Concatenated (1240 Mbps) VC4
Synchronous Transport Signal/Module Signal Level-3 Concatenated
(155 Mbps) VC416C
Synchronous Transport Signal/Module Level-48 Concatenated (2488 Mbps) VC42C
Synchronous Transport Signal/Module level-6 (310 Mbps) VC43C
Synchronous Transport Signal/Module Level-9 Concatenated (465 Mbps) VC11
Virtual Channel 11 VC12
Virtual Channel 12
<RFROMEND>
(Optional) The ending time slot in the source roll port. For bulk rolling only.
The parameter type is PATH, which is the modifier for path commands. VC3
Synchronous Transport Signal/Module Level-1 (51 Mbps) VC44C
Synchronous Transport Signal/Module Level-12 Concatenated (622 Mbps) VC464C
Synchronous Transport Signal/Module Level-192 Concate