DuraTemp TRIANGLE COATINGS, INC.
Tel: 510-895-8000
800-895-8000
Fax: 510-895-8800
www.tricoat.com
Hi Heat, Pure Silicone Enamel, 500° 1100° F.
DuraTemp Product .............. 26 series
VOC:
[as packaged]
........................
White
.......
Silver
grams/liter .................................. 482 ........... 596
lbs./gal ...................................... 4.02 ......... 4.97
APPEARANCE:
[Gloss at 60°]
Initial gloss .............................................. 80 90
After temperature .................................... 20 40
WEIGHT PER GALLON: ...........
White
.......
Silver
10.5 lbs. ...... 9 lbs.
FLASH POINT:
[setaflash]
............................... 45° F.
PACKAGE VISCOSITY: ..................... 75 80 KU
SOLIDS BY VOLUME: ...............
White
.......
Silver
51% ......... 35%
COVERAGE: ..............................
White
.......
Silver
[Theoretical sq.ft./gal. at 1 mil DFT]
....... 515 ........... 560
Required Minimum DFT ............................. 3 mils
Recommended DFT per coat ................. 1.5 mils
[Spread rates vary significantly with blast profile.]
DRY SCHEDULE:
[@ 75° F., 50% RH & 1.5 mils DFT]
Handle
Recoat
High Heat
Catalyzed
8
.
hrs¡
24
.
hrs¡
48
.
hrs¡
Uncatalyzed
NA
24
.
hrs¡
48
.
hrs¡
[Add 24 hours to each for application below 55° F.]
COLOR AVAILABILITY: ............
[See chart back page]
26G700 (H488) .......................................... White
26G710 (P260) ........................................... Black
26G798 (P263) ................................... Aluminum
ORDER CODE: ...................... 26 + gloss + color #
Individual products are identified by the product
series number, followed by a gloss identifier (arbi-
trarily) and ending in the color number For ex-
ample, 26G700 is DuraTemp (26) gloss (G) White
(700).
PACKAGING:
[average]
Two ea. 1 gallon cans/case
[UPS HazPac]
... 20 lbs.
Four ea. 1 gallon cans per case
[truck]
...... 42 lbs.
One ea. 5 gallon metal pail ....................... 50 lbs.
DESCRIPTION:
DuraTemp, 26 series, is a pure silicone enamel for
steel subject to temperatures above 500° F. Above
500° F. organic resins oxidize completely and most
pigments discolor. Inexpensive bar-b-que black
and aluminum paints provide color, but no protec-
tion for the metal. DuraTemp uses a silicone resin
that literally cures to the metal at 500° F. and is not
affected by temperatures of 1200° F. The cured
resin is waterproof and protects the metal when it
cools preventing rusting. Maximum recommended
temperature varies with color from 1100° F. for
aluminum to 500° F. for red and blue. A chart on
page 2 shows the range for the available colors.
DuraTemp is designed for direct application to iron
and steel abrasive blast cleaned to SSPC-SP7
White Metal Blast. However, if the maximum tem-
perature is below 850° F. an inorganic zinc silicate
primer can be used and will provide superior corro-
sion protection. If the painted surface will not be
brought above 500° F. immediately after applica-
tion an optional catalyst, 26B, is recommended to
provide proper dry.
DuraTemps resin system is solvent borne. VOC is
above normal limits in regulated areas, but
DuraTemp is typically legal by a special use ex-
emption. Users/specifiers must check local regula-
tions and secure approvals in advance. DuraTemp
is designed for spray application only. It dries to a
high gloss but drops to a satin when surfaces are
brought to temperature.
USE:
The classic, design use is smokestacks. DuraTemp
is also recommended for incinerators, boilers and
similar surfaces exposed to extreme heat.
ADVANTAGES:
The only way to provide color on surfaces subject
to temperatures above 450° F. and the only way
to provide corrosion protection above 850° F.
White, black and aluminum in stock and pack-
aged for small quantity sales.
LIMITATIONS:
Color selection is limited, see below.
Uniform, thin coats at recommended DFT are
mandatory. Over application will cause failure.
Formulation varies significantly with color. Where
appropriate, physical constants are shown for
White and aluminum, which are the extremes. WARRANTY: The statements made herein, on labels, product bulletins, or by any of Triangle Coatings', Inc. employees or agents concerning this product are given for general information
only. Due to variables beyond Triangles control in application, surface preparation, surface temperature, humidity and other variable factors Triangle assumes no liability for any claim
that may arise out of the use of its products and disclaims any warranty expressed or implied relating to the storage, application, thinning, merchantability, Buyer's assumption of
performance, and the fitness for a particular purpose. Receipt of products from Triangle or its agents constitutes acceptance of the terms of this warranty. In the event that Triangle finds
that the product delivered is not of Triangles standard quality, Triangle will at its sole discretion, either replace the product or refund the purchase price. Triangles choice of one of these
remedies shall be the Buyer's sole remedy. Triangle will under no circumstances be liable for consequential damages, except insofar as liability is mandated by law. Triangle will deliver
products at agreed times insofar as it is reasonably able to do so, but it will not be liable for failure to deliver on time when the failure is beyond its reasonable control.
TRIANGLE COATINGS, INC. 1930 Fairway Drive, San Leandro, CA 94577-5631 Tel: 510-895-8000 800-985-8000
Fax: 510-895-8800
(02/12/99)
DuraTemp Hi Heat, Pure Silicone Enamel, 500° - 1100° F.
Product ................... 26 series
REQUIREMENTS FOR APPLICATION:
Surfaces must be cleaned to SSPC-SP7 White
metal blast. This must be done regardless of
whether or not a primer is used.
Surface and ambient temperature must be +45°
F. and minimum of +5° F. above the dew point.
When painting surfaces that will not be brought
above 500° F. DuraTemp must be catalyzed
and
protected against all water, rain, fog and conden-
sation, for a minimum of three days.
Flammable liquid, take appropriate precautions
especially if used inside a structure.
PRIMING:
Priming is optional.
The only recommended primer is Triangle 929Z
and its use must be limited to surfaces that will not
exceed 850° F.
MIXING:
Catalyzing:
DuraTemp Catalyst, 26B, is added to
DuraTemp base in a 1:7 ratio. The base is short
filled, 7 pints per gallon. A pint of 26B is added. Stir
by hand for minimum 4 minutes. Allow to stand for
5 minutes and stir for additional minute to ensure
homogeneity.
Pot Life:
24 hours when catalyzed. Otherwise un-
limited.
RECOMMENDED THINNING:
Thin after catalyzing using xylene. Reduction varies
with color and method of application. For conven-
tional spray thin to 20 23 sec. with #2 Zahn. For
airless thin to 30 35 sec. with a #2 Zahn. White and
black will require 20 30% reduction; Aluminum a
0 10% reduction. Include projected reduction in
data given to AQMD.
FILM DEVELOPMENT & THICKNESS:
DuraTemp is designed to be applied in two coats,
each with a DFT of 1.5 mils to produce a final DFT
of 3.0 mils. A rate with 3 5% spray loss using
conventional air spray equipment should yield ap-
proximately 325 350 sq.ft./gal.
APPLICATION:
Apply by spray. Conventional is recommended,
airless can work but only with small tips and full
control over film thickness.
Conventional:
Use pressure feed, a pot with dual regu-
lators and a medium-heavy duty production or fin-
ishing gun, Binks 7, 18, 62, 2001 or equivalent. Use
FLASH POINT:
[setaflash]
................. 45° F. (20° C.)
SHIPPING DESCRIPTION:
[CFR 49]
Ground/Air/Vessel: ..... Paint, 3, UN1263, PG II
Required Label: ......... FLAMMABLE LIQUID
Required Marking: ............... PAINT UN1263
IMDG PACKAGING:
FLAMMABLE LIQUID, class 3.2, UN1263, II
IMDG STOWAGE: ............................... Category B
UNIFORM FIRE CODE:
[CFR 29]
........... CLASS I-B
STORAGE TEMPERATURE: ........... 120° F. max.
SHELF LIFE:
[warranted]
................................ 1 Year
HMIS RATINGS: ........ H - 2; F - 3; R - 0; PP - H
.030" .040" fluid nozzle and air cap appropriate
for available air and surface. Use 15 20 psi fluid
pressure and 65 75 psi air pressure.
HVLP:
Use .030" .040" fluid nozzle, Binks 90 91 or
equivalent.
Airless:
Use .013 tip, 1500 1800 psi fluid pressure
as necessary to eliminate tails. Pump size will
vary depending on whether it is necessary to
pump up.
Pumping up more than 15 20 feet will
require