versions at the Internet Archive. Yahoo! is not affiliated with the authors of this page or responsible for its content.
Installing batteries into Moon In My Room KEEP THESE INSTRUCTIONS FOR FUTURE REFERENCE - DO NOT DISCARD
Uncle Milton Inc, Westlake Village, CA 91362
1-888-742-2484 Fax: 818.707.0878 www.unclemilton.com
© UMI, Inc. All rights reserved. Moon In My Room is a trademark
of UMI. Printed in China.
®
Installing batteries into Moon In My Room Tool required - Small Phillips head screwdriver
1. Use a Phillips head screwdriver to remove the battery

cover (See Fig. 1).
2. Insert 4 AA batteries. Make sure the + and - ends

are inserted correctly, as indicated in the battery

compartment.
3. Replace cover.
4. IMPORTANT! Switch Moon in My Room to the

ON position before (see Fig. 2). PLEASE NOTE: The

unit will not activate without the remote control.

To ensure proper functionality, use Moon in
My
Room

in a darkened room.
Problems? Before taking this product back to the store please call us, we can help! 1-888-742-2484 or go to www.unclemilton.com
Figure 3
Installing batteries into the remote control
Tool required - Small Phillips head screwdriver
1. Use a Phillips head screwdriver to remove

the battery door (See Fig. 3).
2. Insert 2 AAA batteries. Make

sure the + and - ends

are inserted correctly,

as indicated in the
battery

compartment.
3. Replace cover.
Figure 1
Figure 2
Battery
cover
2056-0506
AGES 6 AND UP

2056
BATTERY SAFETY INFORMATION
-
Only adults should install and replace batteries.
- Switch toy off before opening battery compartment.
- Insert batteries correctly. Match positive + and negative - signs.
- Alkaline batteries are recommended for best performance.
- Rechargeable batteries are not recommended.
- If rechargeable batteries are used, they are only to be charged under

adult
supervision.
- Rechargeable batteries are to be removed from the product before

they are charged.
- Do not recharge non-rechargeable batteries.
- Only use the batteries specified.
- Only batteries of the same or equivalent type as recommended are to be used.
- Do not mix different types of batteries: alkaline, standard (carbon-zinc)

or rechargeable (nickel-cadmium).
- Do not mix old and new batteries.
- Remove dead or exhausted batteries.
- Remove the batteries during long periods of non-use.
- Always remove exhausted batteries from the toy.
- Battery leakage and corrosion can damage this product.
- Dispose of batteries safely. Recycle where available.
- Do not dispose of batteries in a fire or attempt to open the outer casing.
Never
short-circuit the battery terminals.
- Do not immerse battery-operated toys in water. Wipe clean only. Hanging Moon In My Room

NOTE: The Moon In My Room is only intended to be
installed to a vertical wall.
1. Hang the Moon In My Room by one of the three

hanging holes. (See Fig. 4)
2. Select any one of the 3 hang holes to angle the moon

to your desired position. This directly affects the angle

of the crescents.
Using Moon In My Room IMPORTANT: Before operating, be sure on/off switch
located on the back of Moon In My Room is turned to the
ON position.
NOTE: In order for the moon to function properly, the room
lights should be off.
Auto On/Off
Moon automatically turns on in a darkened room. It
automatically shuts off after 30-minutes if there is no
manual interaction.
Night Light
Moon in My Room is light sensitive, and will only function
in a darkened room. To turn the moon off, press the
ON/OFF button on your remote. Press ON/OFF button
again to reactivate a full moon.
Auto Phase
Your Moon In My Room will cycle through the moon
phases automatically, when you push the automatic
phase button. The moon will cycle from phase to phase in
five-second intervals. In this mode, the moon will
automatically turn off after 30-minutes.
Manual Phase
To manually cycle through the moon phases, press the
manual phase button (see figure 5). If you leave the moon
on in a phase, it will automatically turn off after 30
minutes.
Permanent On/Off using Remote Control
Press and hold the remote ON/OFF button for 5 seconds.
This will turn the moon off and disable the auto light
sensor. Your moon will not turn on automatically in a
darkened room. Hold again for 5 seconds to turn the
moon back on, enabling the auto light sensor function.
Figure 4
Figure 5
On/Off
button
Automatic
phase
button
Manual
phase
button
ON/OFF
Switch
Hanging
holes