pshot of the page taken as our search engine crawled the Web.
The web site itself may have changed. You can check the current page or check for previous versions at the Internet Archive. Yahoo! is not affiliated with the authors of this page or responsible for its content.
TURQUOISE STROKE SWITCHES ORDERING INFORMATION
OPERATION CONCEPT DIAGRAM (reference)
Contact form: terminal type
ULTRA-LONG STROKE,
HIGH CONTACT
RELIABILITY SEALED
SWITCHES
(SAME SIZE AS J TYPE)
TURQUOISE
STROKE
SWITCHES
mm
FEATURES
1. Same size as J type with ultra-long
stroke. For pin plunger type, it
maintains an ultra-long stroke O.T.
(Over Travel) with over 2.2 mm on the
NO side and over 2.5 mm on the NC
side. Variations in operation can be
absorbed.
2. Since contact pressure does not
depend on the operation stroke, the
range of possible use over the entire
stroke is greatly increased.
(Please refer to operation concept
diagram.)
3. High contact reliability to support
low level switching loads
High contact reliability is maintained with
gold plating on both sides of sliding
contact.
4. Highly effective sealing for
resistance against adverse
environments
Immersion protection type
JIS C0920 (water-resistance
experiments for electrical machines and
protection rating against incursion of
solid substances)
D2
JIS D0203 (method for testing moisture
resistance and water resistance in
automotive components)
IP67
IEC529 (rating for outer shell protection)
5. Silent operation
With sliding contact construction there is
no operation noise.
6. Direct operation possible from
lateral direction with pin plunger
(lever-less operation allows space
savings)
7. Contains no harmful substances
(mercury, lead, hexivalent chromium,
cadmium)
TYPICAL APPLICATIONS
1. Automobiles (detection of door
opening and closing and shift lever
position, etc.)
2. Household appliances (propane
stoves, vacuum cleaners, air
conditioners, washing machines, etc.)
13.3
9.6
5.4
NEW
Type of switch
ASQ1: Turquoise
stroke
switch
Size of mounting hole
0:
1:
3 mm standard
type
3 mm without boss
type
Terminal
2:
3:
4:
5:
6:
Wire leads right side type (NC and NO type only)
Wire leads left side type (NC and NO type only)
Solder terminal
PC board terminal
Wire leads (bottom type)
Contact form
1:
2:
3:
SPDT
SPST-NC
(wire lead type only)
SPST-NO
(wire lead type only)
Actuator
0:
7:
8:
Pin plunger
Leaf lever
Simulated leaf lever
Ex.
ASQ1
Remark: Not every combination is available. Please refer to the following table, PRODUCT TYPES.
TF
RF
OF
Stroke
Operation load
Contact pressure
Range of possible use
Oper
ation
load
NC side
NO side
RP (NC)
OP (NC)
OT (NC)
OT (NO)
TTP
OP (NO)
FP
RP (NO)
Standard (mounting boss and
hole center diameter or standoff)
0
NC side
NO side
0
(OFF)
ASQ1
All Rights Reserved © COPYRIGHT Matsushita Electric Works, Ltd. ASQ1
APPLICABLE CURRENT RANGE (reference)
PRODUCT TYPES
1. Terminal type (Mounting hole: 3mm standard type/3mm without boss type)
2. Wire leads bottom type (Mounting hole: 3mm standard type)
3. Wire leads side type (Mounting hole: 3mm standard type)
RATING
1. Rating
1 mA, 5 V DC to 100 mA, 30 V DC
Note: Please consult us regarding 42 V DC rating.
2. Operation environment and conditions
Note: When switching at low and high speeds or under vibration, or in high-temperature, high-humidity environments, life and performance may be
reduced signicantly depending on the load capacity. Please consult us.
3. Electrical characteristics
Actuator
Operating force Max.
Mounting hole: 3mm standard type
Mounting hole: 3mm without boss type
Solder terminal
PC board terminal
Pin plunger
1.5N
ASQ10410
ASQ11510
Leaf lever
1.7N
ASQ10417
ASQ11517
Simulated leaf lever
1.5N
ASQ10418
ASQ11518
Actuator
Operating force Max.
Wire leads bottom type (Mounting hole: 3mm standard type)
Switching type
NC type
NO type
Pin plunger
1.5N
ASQ10610
ASQ10620
ASQ10630
Leaf lever
1.7N
ASQ10617
ASQ10627
ASQ10637
Simulated leaf lever
1.5N
ASQ10618
ASQ10628
ASQ10638
Actuator
Operating force Max.
Wire leads right side type
(Mounting hole: 3mm standard type)
Wire leads left side type
(Mounting hole: 3mm standard type)
NC type
NO type
NC type
NO type
Pin plunger
1.5N
ASQ10220
ASQ10230
ASQ10320
ASQ10330
Leaf lever
1.7N
ASQ10227
ASQ10237
ASQ10327
ASQ10337
Simulated leaf lever
1.5N
ASQ10228
ASQ10238
ASQ10328
ASQ10338
Item
Specications
Ambient and storage temperature
40°C to +85°C (no freezing and condensing)
Allowable operating speed
30 to 500 mm/sec.
Max. operating cycle rate
120 cpm
Withstand voltage (Initial)
Between non-continuous terminals: 600 Vrms, Between each terminal and other exposed metal parts: 1,500 Vrms,
Between each terminal and ground: 1,500 Vrms (at detection current of 1 mA)
Insulation resistance (Initial)
Min. 100 M
(at 100 V DC insulation resistance meter) (Locations measured same as withstand voltage.)
Contact resistance (Initial)
Max. 1
(at contact resistance meter)
Applicable range
100mA
1mA
0
30V
5V
DC
All Rights Reserved © COPYRIGHT Matsushita Electric Works, Ltd. 4. Characteristics
Notes: As long as there are no particular designations, the following conditions apply to the test environment.
Ambient temperature: 5 to 35°C
Relative humidity: 25 to 85% RH
Air pressure: 86 to 106 kPa
5. Protective structure
1) JIS C0920: Waterproof type
A concrete testing method is to check for any adverse effect on the structure after leaving it submerged for 30 minutes
under 1 m of water (with temperature difference between water and switch no larger than 5°C).
2) IEC 529:
IP67 (waterproof type)
A concrete testing method is to check for any adverse effect on the structure after leaving it submerged for 30 minutes
under 1 m of water (with temperature difference between water and switch no larger than 5°C).
3) JIS D0203: Equivalent of D2
A concrete testing method is to check for any adverse effect on the structure after leaving it submerged for 30 minutes
under 10 cm of water (with temperature difference between water and switch no larger than 30°C).
Note: Names of the standards can be found in the section describing features.
6. Operating characteristics
Notes: 1. The above indicates the characteristics when operating the pushbutton from the vertical direction.
2. Indicates operation load for NO contact to achieve ON status.
3. Indicates position for NC contact to achieve OFF status.
4. Indicates position for NO contact to achieve ON status.
5. Indicates position for NC contact to achieve ON status.
6. Indicates position for NO contact to achieve OFF status.
Item
Specications
Electrical
switching
life
5 V DC 1 mA (resistive load)
Min. 5
× 10
5
Switching frequency: 20 times/min.
Conduction ratio: 1:1
Pushbutton operation speed: 100 mm/s
Pushbutton switching position: free position (FP) to operation limit position (TTP)
16 V DC 50 mA (resistive load)
Min. 5
× 10
5
30 V DC 100 mA (resistive load)
Min. 2
× 10
5
Vibration resistance
(malfunction vibration resistance)
Single amplitude: 0.75 mm
Amplitude of vibration: 10 to 55 Hz (4 minutes cycle)
Direction and time: 30 minutes each in X, Y and Z directions
Amplitude of vibration: 5 to 200 Hz (10 minutes cycle)
Acceleration: 43.1 m/s
2
Direction and time: 30 minutes each in X, Y and Z directions
Shock resistance
(malfunction shock resistance)
Shock value: 980 m/s
2
Direction and time: 5 times each in X, Y and Z directions
Vibration resistance endurance
Frequency of vibration: 33.3 Hz, Acceleration: 43.1 m/s
2
Direction and time: 8 hours each in X, Y and Z directions
Terminal strength
6 N min. (each direction) *Terminal deformation possible.
Heat resistance
85°C 500 houres
Cold resistance
40°C 500 houres
Humidity resistance
40°C 95% RH 500 houres
High-temperature, high-humidity resistance
85°C 85% RH 500 houres
Thermal shock resistance
30 min. at 85°C to 30 min at 40°C for 1,000 cycles
Water resistance
Submersed for 30 min. under 1 m of water.
Actuator
Pin plunger
Leaf lever
Simulated leaf lever
Operating Force (max. O.F.) *
Note 2
1.5N
1.7N
1.5N
Total travel Force (max. T.F.) (reference value)
(2.0N)
(3.1N)
(2.8N)
Free Position (max. F.P.)
From mounting boss and hole center line
9.2mm
11.5mm
14.4mm
From standoff
13.4mm
15.7mm
18.6mm
Operating Position on NC side
O.P. (N.C.) *
Note 3
From mounting boss and hole center line
8.7±0.3mm
9.8±0.5mm
12.5±0.5mm
From standoff
12.9±0.3mm
14.0±0.5mm
16.7±0.5mm
Operating Position on NO side
O.P. (N.O.) *
Note 4
From mounting boss and hole center line
8.4±0.3mm
9.3±0.5mm
12.0±0.5mm
From standoff
12.6±0.3mm
13.5±0.5mm
16.2±0.5mm
Release Position on NC side
R.P. (N.C.) *
Note 5
From mounting boss and hole center line
8.8±0.3mm
10.1±0.5mm
12.9±0.5mm
From standoff
13.0±0.3mm
14.3±0.5mm
17.1±0.5mm
Release Position on NO side
R.P. (N.O.) *
Note 6
From mounting boss and hole center line
8.5±0.3mm
9.6±0.5mm
12.4±0.5mm
From standoff
12.7±0.3mm
13.8±0.5mm
16.6±0.5mm
Over travel on N.C. side (min. O.T. (N.C.))
2.5mm
3.1mm
3.3mm
Over travel on N.O. side (min. O.T. (N.O.))
2.2mm
2.6mm
2.8mm
Total Travel Position (T.T.P.)
(reference value)
From mounting boss and hole center line
(5.9mm)
(6.2mm)
(8.7mm)
From standoff
(10.1mm)
(10.4mm)
(12.9mm