chive. Yahoo! is not affiliated with the authors of this page or responsible for its content.
PRESSURE SWITCHES
Features
Manual Reset
Snap-acting, trip free mechanism
Single-pole, single-throw switch,
normally closed
Factory calibrated pressure setpoints
from 200 to 750 psig (14 to 52 bar)
Tamper resistant
LEADING THE WORLD
IN SWITCH DESIGN
The 29PS Series is a manual
reset, single pole, single
throw, snap acting pressure
switch. The 29PS is based on
Sensata Technologies 20PS
pressure switch, long recog-
nized as an industry standard
control device. Features of
this switch include manual
reset, a broad assortment of
port fittings and electrical
connections, and the op-
tion of a panel mount or line
mount design.
Sensata Technologies has
been a leading global supplier
of pressure sensors and
switches for over 50 years.
PRESSURE SWITCHES
29PS Series, Manual Reset
Klixon is a registered trademark of Sensata Technologies
© Copyright Sensata Technologies 2008
Applications
The Model 29PS pressure switch is primarily
applied as an upper limit control on unitary
and central air conditioning systems, heat
pumps, roof top units, and refrigeration
systems.
This hermetic pressure switch employs a
trip-free manual reset function, providing
high reliability in an environmentally sealed,
low-cost package.
Operation
The 29PS utilizes a snap-acting stainless steel
Klixon® disc that reverses its curvature when
pressurized above a customer specified actua-
tion pressure. When the disc snaps, it opens
a set of electrical contacts by means of a
transfer pin. Resetting of the switch must be
accomplished manually by pressing the inte-
grated reset button.
The unique latching mechanism in the 29PS
design assures safe electrical cutout even if
the reset button is held firmly depressed.
This trip-free design prevents the consum-
er from restarting the equipment until the
line pressure has dropped below the release
setpoint. Without this trip-free mecha-
nism, the equipment could be restarted
by simply holding the reset button in the
depressed position, while an overpressure
condition remains.
Product Features
The welded, hermetic design of the 29PS
provides increased reliability and
maintenance-free operation for the lifetime
of the switch. The actuation and release
pressures of the disc are factory calibrated,
simplifying installation and making
the 29PS tamper resistant.
The epoxy potting and rubber boot provide
an environmental seal for the switch
mechanism, protecting it from dust, oil and
moisture. The 29PS is built into a vibration
resistant package.
Its compact size coupled with a wide
variety of threaded and brazed pressure
connections allows the 29PS to be mounted
wherever is most appropriate for the appli-
cation; inside a control box or out in the
elements. Panel-mounted devices are typi-
cally provided with capillary tubes to allow
for convenient access to the reset button.
A variety of line-mounted fittings are avail-
able to simplify installation. Many different
lead termination options are available for
maximum flexibility. Sensata Technologies
529 Pleasant Street, MS B19
Attleboro, MA 02703-2964
Phone 1-888-438-2214
Fax: 508-236-2349
email: sensors@sensata.com
www.sensata.com
Important Notice: Sensata Technologies (Sensata)
reserves the right to make changes to or discontinue any
product or service identified in this publication without
notice. Sensata advises its customers to obtain the latest
version of the relevant information to verify, before placing
any orders, that the information being relied upon is cur-
rent. Sensata assumes no responsibility for infringement of
patents or rights of others based on Sensata applications
assistance or product specifications since Sensata does
not possess full access concerning the use or application of
customers products. Sensata also assumes no responsibil-
ity for customers product designs.
Printed in U.S.A., Reprinted July 21, 2008
Design Specifications
Typical Dimensional Drawings
200 to 750 psig (14 to 52 bar)
For actuation pressures of 200-350 psig (14 - 24 bar), tolerance is ±10 psig (±0.7 bar),
60-70% is standard differential;
351-500 psig (24 - 34.5 bar), ±10 psig (±0.7 bar), 65-75% differential;
Differential = (release setpoint/actuation setpoint) X 100.
Release Tolerance setpoint on all devices (0.2 bar), ±30 psig.
600 psig (41 bar) for actuation pressure up to 400 psig (28 bar);
800 psig (55 bar) for higher actuation pressures
5000 psig (345 bar)
1/4 SAE female flare with deflator 1/4 male NPTF 1/8 male NPTF
1/4 SAE male flare 24 and 36 capillary tubes, straight or flared ends
Single-pole single-throw normally closed at atmospheric pressure with manual reset
Pilot-duty, 375 VA at 120 VAC 5.8 FLA, 34.8 LRA at 120 VAC
2.9 FLA, 15.0 LRA at 240 VAC 240 VAC 6A IND
750 Vrms across open contacts; 1554 Vrms to ground
10,000 cycles
AWG stranded UL style 1056 with 1/2 strip standard
6 and 12 lengths standard, other lengths available and special terminals available
upon request
-20ºF to 150ºF (-29ºC to 66ºC)
-65ºF to 275ºF (-54ºC to 135ºC)
UL recognized File No. SA995 U.S. Category SDFY2;
Canada Category SDFY8 ENEC Certified, PED CE0035 Module B/D
Operating Pressure:
Pressure Differential & Tolerance:
Proof Pressure:
Burst Pressure:
Standard Port Fittings
Electrical Configuration
Electrical Ratings:
Dielectric Strength:
Life at Rated Current:
Leads:
Ambient Temperature:
Fluid Temperature:
Agency Approvals:
Typical Line Mount Construction
Typical Panel Mount Construction
1.15 (29.2)
Max.
1/4 SAE FEMALE
FLARE FITTING
(7/16-20 UNF-2B)
W/DEFLATOR
.63 (16) MAX.
1.45 (37)
MAX.
.88 (22)
MAX.
NYLON SLEEVE
EPOXY FILLED FOR
ENVIRONMENTAL SEAL
.425 (10.8)
MAX.
#18 AWG STRANDED
600V PVC
1/16 INSULATION
3/32 (2.38) COPPER
REFRIGERATION CAPILLARY TUBE
1.25 (31.8)
MAX.
.86 (22)
MAX.
1.50 (38) MAX.
1.45 (37)
MAX.
NYLON SLEEVE
EPOXY FILLED FOR
ENVIRONMENTAL SEAL
#18 AWG STRANDED
600V PVC
1/16 INSULATION
.425 (10.8)
MAX.
1.67 (42.4)
1.69 (42.9)