ffiliated with the authors of this page or responsible for its content.
Electronic Multi-Zone Environmental Alarm System Installation/Owners Manual D-011-0152
Electronic Multi-Zone Environmental Alarm System
Installation/Owners Manual Limitations of the Alarm System or Device
While your alarm system or device is reliable and sophisticated, it does not offer guaranteed protection against
burglary, fire or other emergency. Any security product, whether commercial or residential, is subject to
compromise or failure-to-warn for a variety of reasons. These include: Individuals may gain access through unprotected openings or have the technical sophistication to
bypass an alarm sensor or disconnect an alarm warning device. Monitoring devices will not operate without power. Devices powered by AC will not work if their AC
power supply is off for any reason. If system has battery backup, batteries that are not maintained can
fail to provide the necessary power for devices to function properly. Alarm warning devices such as sirens, bells, and horns may not alert people or awaken sleepers if they
are located on the other side of closed or partly closed doors. If warning devices are on a different level
of the residence from the bedrooms, they are less likely to awaken or alert people inside the bedrooms. Telephone lines needed to transmit alarm signals from a premises to a central monitoring station may
be out of service, and are subject to compromise by sophisticated means of attack. Signals sent by wireless transmitters may be blocked or reflected by metal before they reach the alarm
receiver. Even if the signal path has been recently checked during a weekly test, blockage can occur if
a metal object is moved into the path. Even if the system responds to the emergency as intended and is a monitored alarm system, the
authorities may not respond appropriately. This equipment, like other electrical devices, is subject to component failure. The most common cause of an alarm system not functioning properly is due to inadequate
maintenance. Your alarm system should be tested weekly to make sure all detection devices are
operating properly. Your control panel and keypads should be tested as well.
Installing an alarm system may make you eligible for lower insurance rates, but an alarm system is not a substitute
for insurance. Homeowners, property owners, and renters should continue to insure their lives and property. D-011-0152
i
Table of Contents
General Information............................................................................................................................... 1
Overview ............................................................................................................................................ 1
How to Use This Manual.................................................................................................................... 2
Block Diagrams.................................................................................................................................. 3
Symbols on the Product or Manual Labeling ..................................................................................... 4
Monitoring Screens ............................................................................................................................ 5
Keys ................................................................................................................................................... 6
Base Unit Connections ...................................................................................................................... 7
Access Control and Passwords ......................................................................................................... 8
System Configuration Parameters ..................................................................................................... 9
Sensors............................................................................................................................................ 10
Temperature Sensors ................................................................................................................ 10
Humidity Sensors....................................................................................................................... 11
4-20mA Sensors ........................................................................................................................ 11
Theory of Operation ....................................................................................................... 11
Power Supply / Sensor Voltage Selection...................................................................... 12
Water Sensors ........................................................................................................................... 13
Multi-Function Sensors .............................................................................................................. 13
Contact Closure Sensors ........................................................................................................... 13
Sensor Parameter Descriptions ................................................................................................. 14
Relay Operation ............................................................................................................................... 15
Preparation........................................................................................................................................... 17
Installation............................................................................................................................................ 21
Tools and Supplies Required........................................................................................................... 21
Power Requirements ....................................................................................................................... 21
Mounting the EA800 Rear Plate ...................................................................................................... 21
Install the Wired Sensors ................................................................................................................. 22
EA800 Base Unit Power Connections ............................................................................................. 22
Install the Wireless Sensors............................................................................................................. 22
Connecting Wired Temperature, Contact Closure, and Water Bug Sensors................................... 24
Connecting Wired HA-III+ Humidity Sensors................................................................................... 25
Connecting Wired 4-20mA Sensors................................................................................................. 26
Connecting the EA800 Alarm Outputs ............................................................................................. 27
Programming ................................................................................................................................... 27
Accessing the MAIN MENU for Programming ........................................................................... 28
Configuring System Parameter Settings.................................................................................... 28
Setting the Current Date ............................................................................................................ 31
Setting the Time......................................................................................................................... 32
Adding Wireless Sensors................................................................................................................. 33
Adding a Wireless Temperature Sensor .................................................................................... 33
Adding a Wireless Multi-Function Sensor Using a Wired Temperature Sensor ........................ 35
Adding a Wireless Humidity Sensor........................................................................................... 37
Adding a Wireless Multi-Function Sensor Using a Wired WaterBug Sensor ............................. 38
Adding a Wireless Multi-Function Sensor Using a Wired Contact Closure Sensor ................... 40
Verify Wireless Signal Strength ................................................................................................. 42
Adding Wired Sensors ..................................................................................................................... 43
Adding a Wired Temperature Sensor ........................................................................................ 43
Adding a Wired HA-III+ Humidity Sensor................................................................................... 44
Adding a Wired WaterBug Sensor ............................................................................................. 45
Adding a Wired Contact Closure Sensor ................................................................................... 46
Adding a 4-20mA Sensor........................................................................................................... 47
Configuring the Relays..................................................................................................................... 48 ii
D-011-0152
Operation .................................................................