>and maintenance operations.
Totally plug-in, no wiring needed
TX10KPS
Plug-in technology.
Easy mounting modules.
The TX5KPS is also
available with two
parallel power
supplies, to provide a
total redundancy, a
better endurance and
easy maintenance of
the main
transformer/rectifier. Test menu
Setting of the main working parameters
of the transmitter.
Total menu
The main working parameters (FWD and
RFL of the tetrode amplifier and of the driver,
VG1,VG2, IG1, IG2, Vfil, Ifil, Temp, etc.) are displayed.
59
MOSFET
On the PJxxKPSs front panel, on a user-friendly
graphic interface, all the amplifiers diagnostic
and control capabilities are displayed.
General status menu
Select menu
Setting menu
Exciters menu
Information menu
Power supply menu
RF units menu
Alarms menu
Service menu
Release menu
TX10KPS plug-in 1.2KW power amplifier modules
Each module is self-protected and self-controlled by means of an
internal microprocessor.
60
MOSFET
TECHNICAL SPECIFICATIONS

TX5KPS - TX10KPS
Each 5KW amplifier (PJ5KPS) is
provided with a one internal fan, inlet
and outlet air.
For each PJ5KPS the output air flow is
600 m
3
/h.
The outlet air hole is placed on rear
cover of rack, but other outlet on top
cover of the rack is available. TX5KPS
BROADBAND POWER
Broadcast
EQUIPMENT
Composed of 5 plug-in 1.2KW power amplifier modules easy to
remove without put-off the amplifier.
Built-in RF power combiner and splitter.
Each power amplifier module has its own with switching power
supply.
Available with double exciter and built-in changeover unit.
Available with two parallel main transformers/rectifiers, each one
being able to supply all the amplifier.
Totally self-protected and self-controlled by means of a network of
microprocessor.
TX5KPS
Features
TX10KPS
Composed of 2 TX5KPS, 5KW plug-in power amplifiers coupled by
means a 3dB coupler.
A 2.5 KW dummy load absorbs the unbalanced power between the
two 5 KW amplifiers.
Available with double exciter and changeover unit system.
TX10KPS
Features
These specifications are subject to change without notice.
99/5/CE
99/5/CE
61
MOSFET
Frequency Range:
AC Power Source:
Output Power:
RF Output Connector:
Output Impedance:
RF input connector:
RF input impedance:
Input Driver Power:
Power Consumption:
Power Factor:
Harmonic & Spurious Suppression:
Cooling:
Operating Temperature:
Maximum humidity:
Cabinet Dimensions:
TX5KPS
87.5 108 MHz
Threephase: 380-415 Vac with neutral, 50-60 Hz
5000 W
1 5/8 EIA flange
50 N-type
50 20 W
< 9kW
0.95
Meets or exceeds all FCC and CCIR requirements
Forced ventilation
From -10
°
C to 50
°
C
90% non-condensing
1895 mm (74.61) H
565 mm (22.24) W
850 mm (33.46) D
TX10KPS
87.5 108 MHz
Threephase: 380-415 Vac with neutral, 50-60 Hz
10000 W
1 5/8 EIA flange
50 N-type
50 60 W
< 18kW
0.95
Meets or exceeds all FCC and CCIR requirements
Forced ventilation
From -10
°
C to 50
°
C
90% non-condensing
2 cabinets:
2073 mm (81.61) H
565 mm (22.24) W
850 mm (33.46) D 62
MOSFET
TECHNICAL SPECIFICATIONS

TX5KPS - TX10KPS
AMPLIFIERSTRANSMITTERSANTENNASACCESSORIES
These specifications are subject to change without notice. Per esigenze tecnico-costruttive ci riserviamo il diritto di apportare varianti ai prodotti, senza preavviso.
RVR Elettronica SpA Via del Fonditore 2/2c
Zona Ind.Roveri 40138 Bologna Italy
Phone +39 051 6010506
FAX
+39 051 6011104
e-mail: info@rvr.it - Web: http://www.rvr.it
ELETTRONICA
Revision: 03/2003
MONO and STEREO
Rated output power PTX30LCD:
0-30 W continuously variable (A.L.C.)
Rated output power PTX60LCD:
0-60 W continuously variable (A.L.C.)
Rated output power PTX100LCD:
0-100 W continuously variable (A.L.C.)
R.F output connector:
"N" type
R.F output impedance:
50 Ohm
Frequency range:
87.5 MHz to 108 MHz
Frequency programmability:
direct from front panel
Frequency stability:
±1ppm from -10°C to 50°C
Modulation type:
direct carrier frequency modulation
Spurious & Harmonic suppression: meets or exceeds all FCC and
CCIR requirements
Modulation capability:
meets or exceeds all FCC and CCIR
requirements (typical 240khz MPX
or Mono 210 KHz Stereo)
Asynchronous AM S/N ratio:
>70 dB below reference carrier with
100% amplitude modulation at 400Hz.
no de-emphasis no FM modulation
Synchronous AM S/N ratio:
<50 dB or better below reference carrier
with 100% amplitude modulation at
400Hz. Without de-emphasis,
FM modulation = +75KHz at 400Hz
Transient intermodulation distortion: less than 0.1% (typical 0.05%)
measured with a 3.18KHz square
wave and a 15KHz sine wave
at 100% modulation
AC power requirement:
110-130V, 50-60%
198-250V, 50-60%
Power consumption PTX30LCD:
approx 120VA from AC
Power consumption PTX60LCD:
approx 200VA from AC
Power consumption PTX100LCD:
approx 300VA from AC
Panel size:
483mm (19") W x 88 mm (3 1/2") H
(2 standard rack spaces high)
Overall depth:
344 mm (26 1/2")
Weight PTX30LCD:
13Kg
Weight PTX60LCD:
15.5Kg
Weight PTX100LCD:
15.5Kg
Ambient temperature range:
-10°C to 50°C
Preemphasis:
0
25 microsec.
50 microsec. (CCIR)
75 microsec. (FCC)
AUDIO INPUTS
Left/Mono-Right/Stereo input :
balanced or unbalanced
Left/Mono-Right/Stereo connector:
"XLR" female
MPX input:
unbalanced
MPX connector:
BNC
Input Impedance:
10Kohm or 600Ohm front panel
selectable
Input Level:
from +14 to -13dBm, 1dB step front
panel selectable, internal continuously
selectable
MONAURAL OPERATION
FM S/N ratio:
PTX30LCD
> 83dB (90 dB typical) below + 75KHz
deviation at 400Hz measured in a
20Hz to 20KHz bandwidth with
50 microsec. de-emphasis (RMS)
PTX60LCD and PTX100LCD
> 79dB below + 75KHz deviation at
400Hz measured in a 20Hz to 20KHz
bandwidth with 50 microsec.
de-emphasis (RMS)
Audio frequency response:
±0.5dB, from 20Hz to 15Khz
Total harmonic distortion:
less than 0.02%
Intermodulation distortion:
0.02% or less, measured with a 1KHz
and a 1.3KHz tones, 1:1 ratio, at 100%
modulation
COMPOSITE OPERATION
Composite FM S/N ratio:
PTX30LCD
83dB (90 dB typical) below +75KHz
deviation at 400Hz measured in a
20Hz to 200KHz bandwidth with
50 microsec. de-emphasis (RMS)
PTX60LCD and PTX100LCD
> 79dB below +75KHz
deviation at 400Hz measured in
a20Hz to 200KHz bandwidth with
50 microsec. de-emphasis (RMS)
Composite amplitude response:
±0.1dB from 20Hz to 53KHz
±0.5dB from 53KHz to 100KHz
Composite total harmonic distortion: less than 0.02%
Composite intermodulation distortion:0.03% or less measured with a 1KHz
and a 1.3KHz tones, 1:1
ratio, at 100%
modulation
Stereo separation:
> 50dB (60dB typical)
Audio amplitude response:
±0.5 dB, from 20 Hz to 15 KHz
Total harmonic distorsion:
0.03% or less
Intemodulation distorsion:
0.03% or less, measured with a 1 KHz
and a 1.3 KHz tones, 1:1 ratio, at
100% modulation
Stereo separation:
> 50 dB (60 dB typical)
SCA INPUTS
SCA input:
3 unbalanced
SCA connector:
"BNC" type
SCA input impedance:
10Kohm
SCA input levels:
+10 to -20dBm adjustable
SCA amplitude response:
±0.2dB, from 40KHz to 100KHz
Crosstalk 67KHz SCA
to main or to stereo channel:
65 dB
Crosstalk 92KHz SCA
to main or to stereo channel:
70 dB
OUTPUT SIGNALS
Monitor MPX:
0dBm at 75KHz, minimum load 600Ohm
19KHz Pilot tone:
1Vpp, minimum load 4K7
R.F. output impedance:
50Ohm
R.F. Test:
-30dB, 50Ohm impedance
REMOTE SIGNAL
Remote Connector:
"DB15 female" type
Adjustable external AGC FWD & RFL power
6 analog/digital inputs
1 Inhibit power interlock, BNC type connector
2 relay outputs
1 I2C serial interface
SERIAL INTERFACE
Serial Interface:
RS232, DTE/DCE selectable
Serial Interface:
RS485 (Optional), DTE/DCE selectable
Serial Connector:
"DB9 female" type
TELEMETRY INTERFACE (Optional)
Telemetry signal:
8 Analog/Digital Input
2 Digital Ouputs
1 I2C serial interface
Telemetry Connector:
"DB25 female" type
OPTIONS
/03
External 24V battery
/08 Telemetry
interface
/AUDINP-DIG
Digital audio Input (AES-EBU balanced,
TOS-LINK and S/PDIF)
/TRDSP
Digital audio Input, DSP, RDS built-in
Analogue Audio Input
Conversion:
24bit
Connector:
XLR electronically balanced
Impedance:
600/10K software selectable
Input level:
Software adjustable
Maximum Input Level:
6/18/30 dBu
Digital Audio Input
Connector:
XLR Balanced + optical toslink
Data Formats:
AES/EBU S/PDIF EIAJ-340
Sampling frequencies:
from 32 to 96 KHz
Digital Audio Output
Connector:
PIN RCA Unbalanced
Data format:
S/PDIF
Sampling frequencies:
96 KHz
MPX Output
D/A convert:
24 bit
Pilot tone:
19 KHz ±0,5 Hz
Pilot level:
Adjustable
Pilot phase:
Adjustable
Attenuation:
with 38 KHz carrier suppressed min. -
90 dB
MPX output level:
Adjustable
Stereo separation:
65 dB from 30 HZ to 15 KHz
Noise Output:
MPX -90 dBu
Preemphasys:
50/75 microsec.
Preemphasys:
linearity from 30 Hz to 15 KHz ±0,01
dB
Low pass filter:
15 KHz ripple from 30 HZ to 15 KHz
±0,01 dB
Low pass filter:
attenuation 19 KHz -90 dB
Clipper:
Left and Right channels
Clipper:
MPX composite
AGC:
Left and Right channels
RDS
Specification:
Cenelec 50067 (PI: Program Identification, PS:
Program Service, PTY: Program Type, TP: Traffic
Program Identification, TA: Traffic
Announcement, AF: Alternative Frequencies,
M/S: Music/Speech, PIN: Program Item Number,
RT: Radio Text, EON: Enhanced Other
Networks, TDC: Transparent Data Channel, IH:
In-house Application)
Sub-carrier frequencies:
57 KHz ±1,5 Hz
Synchronization:
Internal or external
Elaboration
A/D conversion:
24 bit
D/A conversion:
24 bit
DSP elaboration:
32 bit
TRDSP
AUDINP-DIG
General Specifications
D/A converter:
24 bit
Sampling Frequency:
From 32 to 96 Khz
2 Regulations audio level normalize to the level set for analog input.
External switch to select the balanced or unbalanced/optic input
Digital Inputs
1 Unbalanced for coaxial cable with PIN/RCA connector (SPDIF)
1 Input for o