ont>. Yahoo! is not affiliated with the authors of this page or responsible for its content.
Untitled Document
I/A Series
®
Intelligent
Differential Pressure Transmitters
IDP10-A with 4 to 20 mA Output Signal
IDP10-V with 1 to 5 VDC Output Signal
Installation, Calibration, Configuration, and Maintenance
An Invensys Company
Contents
Figures ....................................................................................................................... iv
Tables ........................................................................................................................ v
1. Introduction.......................................................................................................... 1
General Description ................................................................................................... 1
Reference Documents ................................................................................................ 1
Transmitter Identification .......................................................................................... 1
Standard Specifications.............................................................................................. 2
Product Safety Specifications .................................................................................... 5
2. Installation ............................................................................................................ 8
Transmitter Mounting ................................................................................................
8
Process
Mounted Transmitter .............................................................................. 9
Pipe
or Surface Mounted Transmitter ................................................................ 9
Installation of Flow Measurement Piping.................................................................. 1
1
Filling System with Seal Liquid ................................................................................ 1
3
Positioning Housing................................................................................................... 1
3
Positioning Display .................................................................................................... 1
3
Cover Locks ............................................................................................................... 1
4
Transmitter Wiring
for IDP10-A.............................................................................. 1</b>5
Accessing Transmitter Field Terminals ............................................................... 1
5
Wiring the Transmitter to a Control Loop ........................................................... 1
6
Putting Transmitter into Operation ............................................................................ 1
8
Taking the Transmitter Out of Operation .................................................................. 1
8
3 Wire Connection .............................................................................................. 19
4 Wire Connection .............................................................................................. 19
Wiring to a Control Loop .................................................................................... 21
Putting Transmitter into Operation ............................................................................ 23
Taking the Transmitter Out of Operation .................................................................. 23
Transmitter Wiring for IDP10-V................................................................................ 19
ii Calibration and Configuration Using the Local Display ...........................................
31
Calibration............................................................................................................ 3
3
IDP10-A and IDP10-V Calibration................................................................ 3
4
Zero Adjustment Using External Zero Button ..................................................... 3
5
Configuration ....................................................................................................... 3
5
IDP10-A and IDP10-V Configuration............................................................ 3
7
Reranging an IDP10-A or IDP10-V Transmitter ........................................... 3
9
IDP10-A and IDP10-V Character Lists.......................................................... 4
0
Testing the Display .................................................................................................... 4
1
Error Messages........................................................................................................... 4
2
4. Maintenance ......................................................................................................... 45
Parts Replacement...................................................................................................... 45
Replacing the Electronics Module ....................................................................... 45
Removing and Reinstalling the Housing Assembly............................................. 46
Replacing the Sensor Assembly........................................................................... 46
Replacing the Terminal Block Assembly ............................................................ 48
Rotating Process Covers for Venting......................................................................... 48
Index ......................................................................................................................... 51
iii
3. Calibration and Configuration ........................................................................... 25
Calibration Setup........................................................................................................ 2
5
Field Calibration Setup .............................................................................................. 2
5
Bench Calibration Setup ............................................................................................ 2
7
General Calibration Notes.......................................................................................... 2
8
iii
Notes for Electronic Version -A and -V .................................................................... 2
9 Figures
1 Transmitter Identification.................................................................................. 1
2
Minimum Allowable Absolute Pressure vs. Process Temperature
with Fluorinert Fill Fluid................................................................................... 4
3 Process
Mounted Transmitter ........................................................................... 9
4 Mounting Transmitter to a Pipe or Surface.......................................................
10
5 Example of Horizontal Process Line Installation.............................................. 1
2
6 Example of Vertical Process Line Installation.................................................. 1
2
7 Positioning Display ........................................................................................... 1
4
8 Accessing Field Terminals ................................................................................ 1
5
9 Identification of Field Terminals....................................................................... 1
5
10 Supply Voltage and Loop Load......................................................................... 1
6
11 Loop Wiring ...................................................................................................... 1
7
12 Wiring Several Transmitters to a Common Power Supply ............................... 1
8
13 Identification of Field Terminals....................................................................... 1
9
14 Three-Wire Connection.....................................................................................
20
15 Four-Wire Connection.......................................................................................
20
16 Loop Wiring ...................................................................................................... 2
1
17 Wiring Several Transmitters to a Common Power Supply (Four-Wire) .......... 2
2
1
8 Field Calibration Setup...................................................................................... 2</b>7
19 Calibration Setup of Electronic Equipment ...................................................... 2</b>7
2
0 Bench Calibration Setup.................................................................................... 2</b>8
21 Local Display Module....................................................................................... 31
2
2 Top Level Structure Diagram............................................................................ 3</b>2
2
3 Calibration Structure Diagram .......................................................................... 3</b>4
2
4 Configuration Structure Diagram...................................................................... 3</b>7
2
5 Display Test Segment Patterns.......................................................................... 4</b>1
2
6 Replacing the