mperature sensing applications require galvanic isolation of the sensor. Fortunately, several
low-cost temperature-sensing integrated circuits (ICs) are easy to isolate. This application note shows two
approaches to isolating temperature sensors.
Sensors, such as temperature sensors, require galvanic isolation when they are mounted in "mechanically
inconvenient" locations such as electrically noisy environments, poorly grounded environments, of instances
where lack of isolation causes safety issues. New families of temperature sensors ease the design of isolated
systems by virtue of a new simple, single-wire method with digitally-multiplexed outputs. These new devices
also offer very low power consumption, simplifying the choices and cost of providing power to the isolated side.

Isolating a temperature sensor with a unidirectional output is straightforward. An example is a temperature
sensor with a frequency or period output, or a thermostatic switch output as shown in Figure 1. This circuit can
take advantage of a new family of sensors such as the MAX6576, whose period is proportional to temperature, or
the MAX6577 whose frequency varies with temperature. Maxim also provides the MAX6501 through MAX6507, a
family of temperature switches (simple devices with outputs that become active at a pre-defined temperature)
which could also be used in this circuit.


Figure 1. This simple isolated temperature sensor provides an output where either frequency or period is
proportional to temperature. It can also be used with temperature activated switches (such as Maxim's MAX6501-
MAX6507) for IC2.

Digital addressable sensors that have been available for some time, and prior articles, have demonstrated how
to interface such devices on the I�C or SMBus (see references 1, 2). However the I�C or SMBus buses require
two isolation circuits for their separate clock and data lines.

A new type of sensor family, the MAX6575H/L, has become available which enables the multiplexing of up to 8
sensors on a simple single-wire bi-directional digital bus. These sensors require a command signal from the
processor, which they respond to after a pre-determined delay (which is covered in detail in their data sheets).
The bi-directional bus requirement is readily satisfied by the same isolation method used for the I�C bus, with
the simplification that only a single bi-directional isolator circuit is required.


Figure 2. This circuit provides up to eight multiple "addressable" sensors on a single digital line. Sensors can be
isolated or non-isolated, or a mixture of both.


Figure 3. Typical communication sequence for Figure 2. Once the DO pin is pulled low and then released, control
of the DO pin is transferred to the MAX6575L/H. The temperature conversion begins on the falling edge of the
externally triggered pulse. The DO line is pulled low by the MAX6575 at a later time. That time is determined by
the device temperature and the time select pins (TS1, TS0). The DO line remains low for 5T�s, where T is the
temperature in degrees Kelvin. The temperature of the device is represented by the edge-to-edge delay of the
externally triggered pulse and the falling edge of the subsequent pulse originating from the device. The start
pulse should be low for at least 2.5 �s (tStart).

The temperature, in degrees Celsius, may be calculated as follows:

T(�C) = [tDx(�s) / timeout multiplier(�s/�K)] - 273.15�K

The multiplier value for each sensor, determined by their TS0 and TS1 line selections (as well as exact model
number, refer to the MAX6575 data sheet for details) is:

IC3, tD1: 5 �s/�K IC4, tD2: 20 �s/�K
IC5, tD3: 80 �s/�K

Although the design of the isolator in Figure 2 is symmetrical, for the sake of this description the left side
connects to the isolated slave devices while the right side goes to the master (typically a microcontroller,
microprocessor, or digital line to a computer). If the computer takes the right line low, the photo diode in Opto 1
turns on the transistor in Opto 1, pulling the slave data line low. The transistor in Opto 1 pulls the data line down
in such a way (via D2) that the photo diode in Opto 1 cannot be activated, which would return the signal around
the loop and latch the circuit if it happened. Data transfer in the opposite direction functions identically except
via Opto 1. The circuit of Figure 2 will drive a total of 8 MAX6575 devices in any combination of isolated or non-
isolated sensors. Also shown is a block depicting the isolated power supply or an alternative battery power.

References
1. "Isolate Data Acquisition On a Bidirectional Bus" by Jerry Steele in Electronic Design, November 6, 1995.
2. "Temperature Sensor Uses I�C Isolator" by Jerry Steele, EDN, June 6, 1996.
A similar version of this article appeared in the June 6, 2000 issue of Electronic Design magazine.

Application Note 1075:
http://www.maxim-ic.com/an1075


More Information
For technical questions and support:
http://www.maxim-ic.com/support

For samples:
http://www.maxim-ic.com/samples

Other questions and comments:
http://www.maxim-ic.com/contact


Related Parts
MAX6501:
QuickView
--
Full (PDF) Data Sheet
--
Free Samples
MAX6502:
QuickView
--
Full (PDF) Data Sheet
--
Free Samples
MAX6503:
QuickView
--
Full (PDF) Data Sheet
--
Free Samples
MAX6504:
QuickView
--
Full (PDF) Data Sheet
--
Free Samples
MAX6505:
QuickView
--
Full (PDF) Data Sheet
--
Free Samples
MAX6506:
QuickView
--
Full (PDF) Data Sheet

MAX6507:
QuickView
--
Full (PDF) Data Sheet
--
Free Samples
MAX6575H:
QuickView
--
Full (PDF) Data Sheet

MAX6575L:
QuickView
--
Full (PDF) Data Sheet
--
Free Samples
MAX6576:
QuickView
--
Full (PDF) Data Sheet

MAX6577:
QuickView
--
Full (PDF) Data Sheet
--
Free Samples

AN1075, AN 1075, APP1075, Appnote1075, Appnote 1075
Copyright � by Maxim Integrated Products
Additional legal notices:
http://www.maxim-ic.com/legal