stallation
Compatibility/Prerequisites
Set Jumpers
Install HBA
Attach Media
Apply Power
View LEDs
Reference
Specifications
FCC and Regulatory Notices
Declaration of Conformity
Laser Safety
Emulex Drivers, Software and Manuals
1 Chapter 1 Installation
Table of Contents
Compatibility
Prerequisites
Set Jumpers
Install HBA
Attach Media
Apply Power
View LEDs
Emulex Drivers, Software and Manuals
2 Installation
Caution
Emulex LightPulse ® Host Bus Adapters (HBAs) contain
electronic components that can be damaged by static
electricity through an electrostatic discharge (ESD) event.
To prevent ESD damage, maintain constant contact with
any grounded metal surface. A grounding wrist strap is
useful for this purpose. Handle the card carefully at all
times and preferably by the edges. Avoid touching
electronic components and keep the card in the original
packaging until you are ready for installation.
Compatibility
Software
Environments
W
indows Server 2003, Windows 2000, Windows NT,
HP-UX, Linux, NetWare, Solaris, AIX
Hardware
Environments
PCI hardware platforms: x86, SPARC, PowerPC,
RS6000 or HP9000
Prerequisites
Host computer must provide 3.3 VDC bus power

One open 32bit or 64bit (64bit recommended) PCI or PCIX bus
slot.

PCI bus clock rate of 33 MHz or 66 MHz

PCIX bus clock rate of 66 MHz, 100 MHz, or 133 MHz

Media and connectors

Emulex Drivers, Software and Manuals
3 Set Jumpers
The host adapter has two jumper blocks (JX1, JX2) that control the host
adapter's device ID. The default device ID is F980.
Device ID
Jumper
setting
F980
JX1:12,
JX2:23
1AE5
JX1:23,
JX2:23
F981
JX1:23,
JX2:12
Emulex Drivers, Software and Manuals
4 Install the Host Bus Adapter Board
Record IEEE and serial numbers.
Each host bus adapter is shipped with a unique 64bit identifier called
the IEEE address. The Fibre Channel industry uses a World Wide
Name (WWN) derived from the IEEE address, and this number is
needed for Fibre Chanel connectivity. The serial number is used when
communicating with Emulex. Both numbers are clearly marked on the
board. We recommend that you record these numbers before
installation.
1.
Turn off and unplug the computer.
2.
Remove the computer case.
3.
Remove the blank panel from an empty 32 or 64bit PCI or PCIX
bus slot. Compare the removed panel to the bracket on the host bus
adapter. Follow steps 58 to change the bracket if they are different
sizes.
4.
Note
The host bus adapter comes with a standard PCI
bracket installed. The lowprofile mounting bracket
is shorter than the standard bracket; approximately
3.11 in. (7.9cm) compared to 4.75 in. (12.06 cm)
long.
Remove the mounting bracket screws from the top of the host bus
adapter.
5.
Remove the bracket and store it for future use.
6.
Align the new mounting bracket tabs with the holes in the HBA.
7.
Note
Be careful not to push the bracket past
the transceiver housing's grounding tabs.
Replace the screws that attach the HBA to the bracket.
8.
Insert the host bus adapter into the empty 32 or 64bit PCI or PCIX
bus slot. Press firmly until it is seated.
9.
Emulex Drivers, Software and Manuals
5 Secure the host bus adapter's mounting bracket to the case with the
panel screw or clip.
10.
Replace the computer case and tighten case screws.
11.
The host bus adapter is now installed in the PC and is ready for media
attachment.
Emulex Drivers, Software and Manuals
6 Attach Media
Note
The host bus adapter will not allow normal data
transmission on an optical link unless it is connected to
another similar or compatible laser product (that is,
multimode to multimode.)
Use multimode or single mode fiber optic cable used with short and
longwave lasers and that adheres to the following specifications:
Fiber Optic Cable
Maximum Length
Minimum Length Connector
62.5/125
µ
m
(multimode)
300 meters at
1.0625 Gb/s
150 meters at
2.125 Gb/s
2 meters
LC
50/125
µ
m (multimode) 500 meters at
1.0625 Gb/s
300 meters at
2.125 Gb/s
2 meters
LC
9/125
µ
m (single mode) 10,000 meters
at 1.0625 Gb/s
10,000 meters
at 2.125 Gb/s
2 meters
LC
Connect the fiber optic cable to the LC connector on the HBA.
1.
Connect the other end of the cable to the Fibre Channel device.
2.
After the media is connected to the host bus adapter, you are ready to apply
power to the computer.
Emulex Drivers, Software and Manuals
7 Apply Power
Verify that the host bus adapter is securely installed in the computer.
1.
Verify that the correct media is attached.
2.
Plug in and turn on the computer.
3.
Observe LEDs for Power On Self Test (POST) results.
4.
View LEDs
Green and yellow display lights (LEDs) can be seen through openings in the
host bus adapter's mounting bracket. Green indicates power and yellow
signifies port activity.
POST conditions and results are summarized in this table.
Green
LED
Yellow
LED
State
OFF
OFF
Wakeup failure (dead board)
OFF
ON
POST failure (dead board)
OFF
Slow blink (1 Hz)
Wakeup failure (dead board)
OFF
Fast blink (4 Hz)
Failure in POST (dead board)
OFF
Flashing (irregular)
POST processing in progress
ON
OFF
Failure while functioning
ON
ON
Failure while functioning
ON
Slow blink (1 Hz)
Normal 1 Gb link rate
ON
Fast blink (4 Hz)
Normal 2 Gb link rate
Blink (1 Hz)
OFF
Normal link down or not yet started
Emulex Drivers, Software and Manuals
8 Chapter 2 Reference
Table of Contents
Specifications
FCC and Regulatory Notices
Declaration of Conformity
Laser Safety
Emulex Drivers, Software and Manuals
9 Reference
Specifications
Parameter
Range
Media
Interface
The Pegasus ASIC interfaces to the physical media through
an FC0 Media Interface (FCPI compliant transceiver),
and then connects through an optical fiber LC connector.
Physical
Dimensions
The PCI adapter accommodates two form factors:
The short PCI form factor, 6.875 inches by 4.2
inches, with a fullheight bracket

The lowprofile MD2 form factor, 6.600 inches by
2.536 inches, with a lowprofile bracket.

Power
Requirements
+ 3.3 VDC, + or 5 % , 2.3A typical (3.3A maximum)
Airflow
100 lf/min (minimum)
Temperature
32° to 113° F (0° to 45° C), Operating
40° to 158° F (40° to 70° C), Storage
Humidity
5% to 95% noncondensing
Agency
Approvals for
LP9802
Class 1 Laser Product per DHHS 21CFR (J) & EN60825
UL recognized to UL1950
CUR recognized to CSA22.2, No.950
Baurtcertified by TUV to EN60950
FCC Rules, Part 15, Class A
Industry Canada, ICES003, Class A
EMC Directive 89/336/EEC (CE Mark)
EN55022, Class A
EN55024
Australian EMC Framework (CTick Mark)
AS/NZS 3548: Class A
Japan VCCI, Class A
Emulex Drivers, Software and Manuals
1
0 FCC and Regulatory Notices
CLASS 1 LASER PRODUCT
LASER KLASSE 1
LUOKAN 1 LASERLAITE
APPAREIL A` LASER DE CLASSE 1
Model LP9802F2/LP982F2/LP9802DCF2
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a
Class A digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference when
the equipment is operated in a commercial environment. This equipment
generates, uses, and can radiate radio frequency energy and, if not installed
and used in accordance with the instruction manual, may cause harmful
interference to radio communications. Operation of this equipment in a
residential area is likely to cause harmful interference in which case the user
will be required to correct the interference at his own expense. Shielded cables
must be used between this equipment and attached peripheral devices. The
reader is cautioned that changes or modifications made to the equipment not
expressly approved by Emulex could void the user's authority to operate this
equipment. The above statement applies to products marketed in the USA
This class A digital apparatus meets all requirements of the Industry Canada
(IC) Interference Causing Equipment Standard (ICES003).
Cet appareil numerique de la Classe A respecte toutes les exigences du
reglement sur le materiel brouilleur du Canada.
This statement applies to products marketed in Canada.
Responsible Party: Paul Folino, CEO, Emulex Corporation, 3535 Harbor
Blvd., Costa Mesa, CA 92626, USA, (714) 6625600
VCCI Notices and Translations (Japan Only
)
Note
VCCI regulations provide that changes or modifications not
expressly approved by Emulex Corporation could void your
authority to operate this equipment.
Emulex Drivers, Software and Manuals
1
1 Translation:
This is a Class A product. In a domestic environment this product may cause
radio interference in which case the user may be required to take adequate
measures. VCCIA
Manual Notice
Translation:
This is a Class A product based on the standard of the Voluntary Control
Council for Interference by Information Technology Equipment (VCCI). If
this equipment is used in a domestic environment, radio disturbance may
arise. When such trouble occurs, the user may be required to take corrective
actions.
Emulex Drivers, Software and Manuals
1
2 Declaration of Conformity
LP9802F2/X2 /