ellpadding=7 cellspacing=0 width=100% bgcolor=ccccff> « back to results for ""
Below is a cache of http://www.polaroid.com/service/userguides/ce/remote_ug.pdf. It's a snapshot of the page taken as our search engine crawled the Web.
The web site itself may have changed. You can check the current page or check for previous versions at the Internet Archive. Yahoo! is not affiliated with the authors of this page or responsible for its content.
Programming the Polaroid Universal Remote Control
1
Programming the Polaroid Universal Remote Control

Products Affected: FLM-2601, 3201, 3701, 4201; PLA-4205, 4240


Following are two sets of instructions for programming your Polaroid Universal Remote
Control to work with other devices in addition to your Polaroid TV. (If you only wish to
use the remote control with your Polaroid TV, no additional programming is
necessary.) Begin with the Direct Programming Setup, and if unsuccessful, go on to the
Auto Code Search Setup. Note: Some remotes will only work with Polaroid TVs
when using the TV function.


Direct Programming Setup
This method requires use of one of the device codes found in the
Device Code Table

(see page 3). Begin with the first code listed for your device.

1 Turn the device power off and point the Polaroid Universal Remote Control at the
device you wish to control.

2 Momentarily press a device button on the Polaroid Universal Remote Control (TV,
DVD, CBL, or AUX). When you release the device button the red LED at the top of the
remote will blink once.
Note: For devices other than a TV, DVD, or Cable Box, use the AUX key.

3 Press and hold the SET button (top-left button) until you see the LED blink once,
followed by two short blinks. Release the SET button after you see the two short LED
blinks.

4 Enter the 5-digit code from the code table for the device you want to control. The LED
blinks once each time you press a numbered button. After you enter the last digit:

a) If the code you entered is the correct code for your device, you will see the LED
blink twice. Go to step 5.
b) If the code you entered is not the correct code for your device, you will see the
LED blink once. Repeat steps 2-4, this time choosing the next code in the list.

5 Press the Power button (top right-side button) on the remote and your device power
should turn on. If the power does not turn on, repeat the entire procedure beginning with
step 1.

If you are unable to program the remote properly after two or more attempts using the
Direct Programming Setup, go on to the Auto Code Search Setup (see next page).
2
Auto Code Search Setup

This method does not require use of the Device Code Table.

1 Turn the device power off and point the Polaroid Universal Remote Control at the
device you wish to control.

2 Momentarily press a device button on the Polaroid Remote Control (TV, DVD, CBL, or
AUX). When you release the device button the red LED at the top of the remote will blink
once.
Note: For devices other than a TV, DVD, or Cable Box, use the AUX key.

3 Press and hold the SET button (top-left button) until you see the LED blink once,
followed by two short blinks. Release the SET button after you see the two short LED
blinks.

4 Press 9 - 9 - 1 on the number pad. Each time you press the number 9 button the LED
blinks once. When you press the number 1 button, the LED blinks twice.

5 Enter the following number, depending on the device you are trying to control. When
you release the button, you should see two short LED blinks.

Cable or Satellite box Press 0
TV Press 1
DVD player Press 2
Audio device or VCR Press 3

6 Momentarily press the power button (top-right button) and release it.

7 Press the CH+ button, slowly and repeatedly, until the device you want to control turns
on. Stop pressing immediately when the device power turns on.

Note: If you press the CH+ button too quickly you may by mistake save the wrong code,
in which case the remote control will not turn the device power on. Start at step 1 and
repeat the programming steps again.

8 When the device turns on, press and hold the SET button until you see the LED blink
twice. The code is now saved, and the remote should operate properly.